Home › BODY ELECTRICAL › AUDIO / VISUAL › RADIO ANTENNA CORD

RADIO ANTENNA CORD > INSTALLATION

for Preparation Click here



1. INSTALL ANTENNA CORD SUB-ASSEMBLY

HINT:
The double-sided tape and tape are not available as supply parts. If these tapes still have enough adhesion to secure the roof headlining and antenna cord, reuse the tapes. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedures below.



  1. Apply new double-sided tape.


    E129190E01


    1. Remove the double-sided tape from the roof headlining assembly.

    2. Peel off the appropriate amount of new double-sided tape. Be careful not to touch the adhesive surface.

    3. Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.

    4. Peel off the backing sheet from the double-sided tape.



  1. Install the antenna cord to the roof headlining assembly from the front of the vehicle.


    E134767E02

  1. Put the strips of the tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.

    HINT:
    1. If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.
    2. For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.
    3. For the right rear corner of the roof headlining assembly, align the marking tape on the antenna cord with the rear edge of the roof headlining, and secure the antenna cord to the roof headlining assembly with tape.
    4. For the part of the antenna cord near the center of the roof headlining assembly, position the marking tape on the antenna cord within the area indicated by the marking line. Secure the antenna cord to the roof headlining assembly with tape as shown in the illustration. (without sliding roof)



2. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    B139560
  1. Pull the roof headlining assembly into the vehicle through the rear left door.

  1. Engage the 4 clips.

  1. Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

  1. Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

  1. Install the radio setting condenser to the front pillar RH with the bolt.



  1. Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.


    B147610E01



3. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    B139561
  1. Pull the roof headlining assembly into the vehicle through the rear left door.

  1. Engage the hook, 4 clips, and 2 fasteners.

  1. Connect the sliding roof drive gear connector.

  1. Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

  1. Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

  1. Install the radio setting condenser to the front pillar RH with the bolt.



  1. Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.


    B147611E01



4. INSTALL SUNSHADE TRIM HOLDER (w/ Rear Sunshade)


    B132143
  1. Engage the 2 claws.



    B132092
  1. Using a screwdriver, turn the pin of each sunshade trim holder 90°to install the sunshade trim holders.



5. INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    B147634E01
  1. Align the paint mark on the inner surface of the opening trim moulding with the notch of the roof headlining, and install the sun roof opening trim moulding so that joining point of the opening trim is on the left side of the vehicle as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.



6. INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)


    B132096
  1. Push the light bulb holder in the direction indicated by the arrow in the illustration to engage the claw.

  1. Engage the 4 claws.



    B132094
  1. Engage the 6 claws and install the spot light assembly.



7. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)


    B139562
  1. Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.



    B139563
  1. Engage the 4 claws.



    B139564
  1. Engage the 4 claws and install the lens cover.



8. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY


    B132101
  1. Assemble the front assist grip sub-assembly as shown in the illustration.



    B132102
  1. Install the front assist grip sub-assembly.

    HINT:
    Use the same procedures for the RH side and the LH side.



9. INSTALL REAR ASSIST GRIP SUB-ASSEMBLY

HINT:
Use the same procedures for the rear side and the front side.



10. INSTALL VISOR HOLDER
  1. Engage the 2 claws.



  1. Push in the visor holder and turn it approximately 45°as shown in the illustration.


    B132103E01



11. INSTALL VISOR ASSEMBLY LH


    B139565
  1. Engage the 2 clips and install the visor assembly LH.



    B139566
  1. Engage the 4 claws and install the visor bracket cover.



12. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side.



13. INSTALL ROOF CONSOLE BOX ASSEMBLY


    B132065
  1. Connect the connectors.

  1. Engage the 2 claws and 2 clips, and then install the roof console box assembly.



14. INSTALL FRONT PILLAR GARNISH LH


    B132100E01
  1. Remove the protective cover.



    B132098E01
  1. Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish LH.



15. INSTALL FRONT PILLAR GARNISH RH


    B132099E01
  1. Remove the protective cover.



    B132097E01
  1. Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish RH.



16. INSTALL ROOF SIDE INNER GARNISH LH


    B132063
  1. Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.



17. INSTALL ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedures for the RH side and the LH side.



18. INSTALL UPPER CENTER PILLAR GARNISH LH


    B132060
  1. Engage the clip.

  1. Install the upper center pillar garnish LH with the bolt.



19. INSTALL LOWER CENTER PILLAR GARNISH LH


    B132058
  1. Engage the 2 claws and 2 clips, then install the lower center pillar garnish LH.



20. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B131996
  1. Install the floor end of the front seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



21. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)


    B131995
  1. Engage the 3 claws and install the lap belt outer anchor cover.



22. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B132081E01
  1. Install the front door opening trim weatherstrip LH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.



23. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B132116E01
  1. Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.



24. INSTALL FRONT DOOR SCUFF PLATE LH


    B132067
  1. Engage the 7 claws and 3 clips, then install the front door scuff plate LH.



25. INSTALL UPPER CENTER PILLAR GARNISH RH

HINT:
Use the same procedures for the RH side and the LH side.



26. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedures for the RH side and the LH side.



27. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side.



28. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedures for the RH side and the LH side.



29. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B132083E01
  1. Install the front door opening trim weatherstrip RH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.



30. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side.



31. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.



32. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH


    B136490
  1. Engage the 3 claws to install the rear door inner glass weatherstrip.



33. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B141703
  1. Engage the claw to install the No. 1 door scuff plate clamp.

  1. Connect each connector.



    B136450
  1. Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.



    B136449
  1. Engage the 7 clips to install the rear door trim board to the rear door panel.

  1. Install the 3 screws.



34. INSTALL DOOR ASSIST GRIP COVER LH


    B136448
  1. Engage the 6 claws and install the door assist grip cover.



35. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    B136446
  1. Engage the 3 claws to install the rear door inside handle bezel plug.



36. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH (for Reclining Seat Type)


    B139084
  1. Install the rear seat reclining control cable.



    B139083
  1. Engage the 2 clips and claw and then install the reclining remote control lever sub-assembly.

  1. Install the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    B144036E01
  1. Adjust the control lever to set the rear reclining adjuster assembly to its upper most position.

  1. Pull plate A toward the front of the vehicle to lock the plate.



37. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH (for Reclining Seat Type)


38. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B132080E01
  1. Install the rear door opening trim weatherstrip LH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.



39. INSTALL REAR DOOR SCUFF PLATE LH


    B132068
  1. Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.



40. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B132082E01
  1. Install the rear door opening trim weatherstrip RH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.



41. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.



42. INSTALL CENTER SEATBACK ASSEMBLY (for Reclining Seat Type)


    B140592
  1. Install the center seatback assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



43. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)


    B139077
  1. Install the separate type rear seatback assembly LH with the 2bolts and 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    B139081E01
  1. Engage the 3 clamps and install the cover.



    B139076E01
  1. Install the 2 rear seat belts.



44. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Reclining Seat Type)


    B139079
  1. Install the separate type rear seatback assembly RH with the 2 bolts and 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    B139082E01
  1. Engage the 3 clamps and install the cover.



    B139078E01
  1. Install the rear seat belt.



45. INSTALL REAR SEATBACK COVER (for Reclining Seat Type)


46. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    B136561
  1. Install the rear side seatback assembly with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



47. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)


48. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    B136539
  1. Install the separate type rear seatback assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



49. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)


    B134700
  1. Install the separate type rear seat back assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



50. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


51. INSTALL REAR SEAT HEADREST ASSEMBLY


52. INSTALL REAR SEAT CUSHION ASSEMBLY


    B140584E01
  1. Attach the front hooks of the bench type rear seat cushion assembly to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the bench type rear seat cushion assembly, make sure that the seat belt buckle is not under the bench type rear seat cushion assembly.



53. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)
  1. Place the seat in the cabin.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

    NOTICE:
    Check that the seat is locked.



    B140607
  1. Temporarily install the front side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

    NOTICE:
    Check that the seat is locked.



    B139102
  1. Temporarily install the rear side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



54. INSTALL SEAT TRACK COVER RH (for Power Seat)


    B139100E01
  1. Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the inner seat track bracket cover to engage claw B.



55. INSTALL SEAT TRACK COVER LH (for Power Seat)


    B139099E01
  1. Slide the seat track cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the seat track cover to engage claw B.



56. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat)


57. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
  1. Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.

  1. Connect the connector and clamp.

  1. Move the front seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.



    B139101
  1. Temporarily install the front seat track bracket with the 2 bolts.

  1. Move the front seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.



    B139102
  1. Temporarily install the rear seat track bracket with the 2 bolts.

  1. Move the front seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



58. INSTALL INNER SEAT TRACK BRACKET COVER LH (for Manual Seat)


    B139100E01
  1. Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the seat track bracket cover inner to engage claw B.



59. INSTALL SEAT TRACK COVER LH (for Manual Seat)


    B139099E01
  1. Slide the seat track cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the seat track cover to engage claw B.



60. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)


61. INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)


62. INSTALL SEAT TRACK COVER LH (for Power Seat)


63. INSTALL SEAT TRACK COVER RH (for Power Seat)


64. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat)


65. INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)


66. INSTALL INNER SEAT TRACK BRACKET COVER RH (for Manual Seat)


67. INSTALL SEAT TRACK COVER RH (for Manual Seat)


68. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)


69. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for LHD)


  1. Engage the 6 clamps and clip and install the No. 2 antenna cord sub-assembly.


    E129184E01



70. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for RHD)


  1. Engage the 6 clamps and clip and install the No. 2 antenna cord sub-assembly.


    E129185E01



71. INSTALL NO. 2 HEATER TO REGISTER DUCT


    B134021E02
  1. Install the No. 2 heater to register duct with the 2 screws <F>.



72. INSTALL NO. 3 HEATER TO REGISTER DUCT


    B134020E02
  1. Install the No. 3 heater to register duct with the 3 screws <F>.



73. INSTALL NO. 1 HEATER TO REGISTER DUCT


    B134019E02
  1. Install the No. 1 heater to register duct with the 3 screws <F>.



74. INSTALL DEFROSTER NOZZLE ASSEMBLY


    B134018E02
  1. Install the defroster nozzle assembly with the 3 screws <F>.



75. INSTALL SIDE NO. 2 DEFROSTER NOZZLE DUCT


    B134017E02
  1. Install the side No. 2 defroster nozzle duct with the screw <F>.



76. INSTALL SIDE NO. 1 DEFROSTER NOZZLE DUCT


    B134016E02
  1. Install the side No. 1 defroster nozzle duct with the screw <F>.



77. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Engage the 5 claws.

    NOTICE:
    Do not allow the wire harness to get caught in the claws.



  1. Install the 2 bolts <H> or <O> and 2 nuts <C> or <I>.


    B134014E04

  1. Engage each clamp.

  1. Install the bolt <J>.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the 2 passenger airbag bolts <K>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect each connector and install the instrument panel safety pad assembly.



  1. with Plasmacluster:



    1. Connect the connector.


      B134012E04



78. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY


    C132564E01
  1. Connect the connector (yellow colored one).



79. INSTALL NO. 1 DEFROSTER NOZZLE GARNISH


    B134011E01
  1. Connect each connector.

  1. Engage the 4 guides.

  1. Engage the 8 clips and install the No. 1 defroster nozzle garnish.



80. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
  1. Connect the connector.



    E129167
  1. Install the front No. 2 speaker assembly with the 2 bolts.



81. INSTALL INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY


    B134009E01
  1. Engage the 2 guides.

  1. Engage the 6 claws and the 2 clips to install the instrument panel No. 1 speaker panel sub-assembly.



82. INSTALL INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY


    B134007
  1. Engage the 4 clips and install the instrument panel No. 1 register assembly.



83. INSTALL FRONT PILLAR GARNISH LH


    B132100E01
  1. Remove the protective cover.



    B132098E01
  1. Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish LH.



84. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedures for the RH side and the LH side .



85. INSTALL INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY


    B134010E01
  1. Engage the 2 guides.

  1. Engage the 6 claws and the 2 clips to install the instrument panel No. 2 speaker panel sub-assembly.



86. INSTALL INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY


    B134008
  1. Engage the 4 clips and install the instrument panel No. 3 register assembly.



87. INSTALL FRONT PILLAR GARNISH RH


    B132099E01
  1. Remove the protective cover.



    B132097E01
  1. Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish RH.



88. INSTALL NO. 1 CONSOLE BOX INSERT FRONT


    B134006E01
  1. Engage the clip.

  1. Install the No. 1 console box insert front with the 3 screws <F>.



89. INSTALL NO. 2 CONSOLE BOX INSERT FRONT


    B134005E01
  1. Engage the clip.

  1. Install the No. 2 console box insert front with the 3 screws <F>.



90. INSTALL CONSOLE BOX ASSEMBLY


    B134002E01
  1. Install the 2 screws <F>.



    B134003E01
  1. Install the console box assembly with the 2 bolts <G>.



91. INSTALL CONSOLE BOX CARPET


    B134004
  1. Install the console box carpet.



92. INSTALL CONSOLE BOX POCKET
  1. Install the console box pocket.



93. INSTALL RADIO TUNER OPENING COVER WITH HEATER CONTROL PANEL ASSEMBLY (w/o Radio Receiver)
  1. Connect the connector.



    B137278E01
  1. Engage the 6 clips.

  1. Install the radio tuner opening cover with heater control panel assembly with the 4 bolts <N>.



94. INSTALL RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Radio Receiver)


    E131401
  1. Connect each connector.

  1. Engage the 4 clips.

  1. Install the radio receiver with heater control panel assembly with the 4 bolts.



95. INSTALL INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY
  1. Connect the connector.



    B134001
  1. Engage the 7 clips and install the instrument panel No. 2 register assembly.



96. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY
  1. Connect each connector.



    B141243E01
  1. Engage the 2 claws and 2 clips.

  1. Install the lower instrument cluster finish panel center sub-assembly with the 2 screws <F>.



97. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle)


    B144603E01
  1. Connect the connector and engage the clamp.

  1. Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.



98. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)


    B144604
  1. Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.



99. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle)
  1. with Seat Heater System:

    1. Connect each connector.



    B148447
  1. Engage the 6 claws and the 3 clips to install the floor shift position indicator housing sub-assembly.



100. INSTALL UPPER CONSOLE PANEL (for Manual Transaxle)


    B145877
  1. Engage the 2 claws and the 5 clips to install the upper console panel as shown in the illustration.



101. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B144605
  1. Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.



102. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B144599
  1. Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.



103. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle)


    B148448
  1. Install the shift lever knob sub-assembly.



104. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B144601
  1. Install the shift lever knob sub-assembly.



105. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B133992E01
  1. Engage the 3 claws and 3 clips.

  1. Install the 4 screws <B>.

  1. Install the lower instrument panel sub-assembly with the bolt <A>.



106. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY


    B133989E01
  1. Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover.



107. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side.



108. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.



109. INSTALL COMBINATION METER ASSEMBLY


    B133987E01
  1. Connect each connector.

  1. Install the combination meter assembly with the 4 screws <E>.



110. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1


    B133985E01
  1. Engage the guide and the 4 claws.

  1. Install the instrument cluster finish panel with the 2 clips.



111. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    B144612
  1. Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.



112. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector.



    B133986
  1. Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.



113. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    C132546
  1. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

  1. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.



114. ADJUST SPIRAL CABLE SUB-ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.



    C107193
  1. Rotate the spiral cable counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.



    C107194E01
  1. Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.



115. INSTALL STEERING COLUMN COVER


    B137294E01
  1. Engage the claw and install the upper steering column cover.

  1. Engage the 2 claws and install the lower steering column cover.

  1. Install the steering column cover with the 2 screws <D>.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



116. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH


    B147263E01
  1. Install the air hose and connect the connector.

  1. Engage the 2 claws and the DLC3.

  1. Engage the claw and the 4 clips.

  1. Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.



117. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B132116E01
  1. Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.



118. INSTALL FRONT DOOR SCUFF PLATE LH


    B132067
  1. Engage the 7 claws and 3 clips, then install the front door scuff plate LH.



119. INSTALL STEERING WHEEL ASSEMBLY


    C132543E01
  1. Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.



120. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.



    C133859
  1. Support the steering pad with one hand.

  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.



    C141759
  1. Using a "TORX" socket (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



121. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    C141760
  1. Engage the claw and install the No. 3 lower steering wheel cover.



122. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    C142024
  1. Engage the claw and install the No. 2 lower steering wheel cover.



123. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


124. INSPECT FRONT SEAT ASSEMBLY


125. INSPECT FRONT SEAT ADJUSTER ASSEMBLY


126. INSPECT STEERING PAD


    C141754
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).



127. INSPECT SRS WARNING LIGHT
(Click here)