Home › BODY ELECTRICAL › AUDIO / VISUAL › RADIO ANTENNA CORD

RADIO ANTENNA CORD > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)


2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment (Click here).



4. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    C141756
  1. Using a screwdriver, disengage the claw and remove the No. 3 lower steering wheel cover.

    HINT:
    Tape up the screwdriver tip before use.



5. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    C141757
  1. Using a screwdriver, disengage the claw and remove the No. 2 lower steering wheel cover.

    HINT:
    Tape up the screwdriver tip before use.



6. REMOVE STEERING PAD


    C141758E02
  1. Using a "TORX" socket (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.



    C133859
  1. Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector from the steering pad.

  1. Disconnect the 2 airbag connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the steering pad.



7. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and the steering main shaft.

  1. Disconnect the connectors from the spiral cable.



    C132542E01
  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)



8. REMOVE FRONT DOOR SCUFF PLATE LH


    B132067
  1. Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.



9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B132116E01
  1. Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH


    B147263E01
  1. Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower instrument panel finish panel LH.



11. REMOVE STEERING COLUMN COVER


    B137294E01
  1. Remove the 2 screws <D>.

  1. Disengage the 2 claws and remove the lower steering column cover.

  1. Disengage the claw and remove the upper steering column cover.



12. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.



    C132546
  1. Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.



13. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY


    B133986
  1. Disengage the 3 claws and the 2 clips.

  1. Disconnect each connector and remove the instrument panel sub-assembly.



14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    B144612
  1. Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.



15. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1


    B133985E01
  1. Remove the 2 clips.

  1. Disengage the guide and 4 claws and then remove the instrument cluster finish panel.



16. REMOVE COMBINATION METER ASSEMBLY


    B133987E01
  1. Remove the 4 screws <E>.

  1. Disconnect each connector and remove the combination meter assembly.



17. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.



18. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH


19. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY


    B133988E01
  1. Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.



20. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Remove the bolt <A>.



    B133992E01
  1. Remove the 4 screws <B>.

  1. Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.



21. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle)


    B148446
  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



22. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B144609
  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



23. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B144599
  1. Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.



24. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B144605
  1. Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.



25. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle)


    B148447
  1. Disengage the 6 claws and the 3 clips, and then remove the floor shift position indicator housing sub-assembly.

  1. with Seat Heater System:

    1. Disconnect each connector.



26. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)


    B144607E01
  1. Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.



    B144602
  1. Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.



27. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle)


    B144603E01
  1. Disengage the 3 claws and the 5 clips.

  1. Disengage the clamp.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.



28. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)


    B144604
  1. Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.



29. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY


    B141243E01
  1. Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.

    HINT:
    Set the shift lever in the D position.



30. REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY


    B133998E01
  1. Apply protective tape to the areas shown in the illustration.



    B144610
  1. Using a moulding remover, disengage the 3 clips.



    B144611
  1. Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the instrument panel No. 2 register assembly.



31. REMOVE RADIO TUNER OPENING COVER WITH HEATER CONTROL PANEL ASSEMBLY (w/o Radio Receiver)


    B137278E01
  1. Remove the 4 bolts <N>.

  1. Disengage the 6 clips and remove the radio tuner opening cover with heater control panel assembly.

  1. Disconnect the connector.



32. REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Radio Receiver)


    E131401
  1. Remove the 4 bolts.

  1. Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver with heater control panel assembly.



33. REMOVE CONSOLE BOX POCKET
  1. Remove the console box pocket.



34. REMOVE CONSOLE BOX CARPET


    B134004
  1. Remove the console box carpet.



35. REMOVE CONSOLE BOX ASSEMBLY


    B134002E01
  1. Remove the 2 screws <F>.



    B134003E01
  1. Remove the 2 bolts <G> and the console box assembly.



36. REMOVE NO. 2 CONSOLE BOX INSERT FRONT


    B134005E01
  1. Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 2 console box insert front.



37. REMOVE NO. 1 CONSOLE BOX INSERT FRONT


    B134006E01
  1. Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 1 console box insert front.



38. REMOVE FRONT PILLAR GARNISH LH


    B132056E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish LH.

  1. Remove the clip <A> from the vehicle body.



    B132100E01
  1. Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



39. REMOVE INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY


    B134007
  1. Disengage the 4 clips and remove the instrument panel No. 1 register assembly.



40. REMOVE INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY


    B134009E01
  1. Disengage the 6 claws and the 2 clips.

  1. Disengage the 2 guides and remove the instrument panel No. 1 speaker panel sub-assembly.



41. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)


    E129167
  1. Remove the 2 bolts and front No. 2 speaker assembly.

  1. Disconnect the connector.



42. REMOVE FRONT PILLAR GARNISH RH


    B132055E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish RH.

  1. Remove the clip <A> from the vehicle body.



    B132099E01
  1. Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



43. REMOVE INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY


    B134008
  1. Disengage the 4 clips and remove the instrument panel No. 3 register assembly.



44. REMOVE INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY


    B134010E01
  1. Disengage the 6 claws and the 2 clips.

  1. Disengage the 2 guides and remove the instrument panel No. 2 speaker panel sub-assembly.



45. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedures for the RH side and the LH side .



46. REMOVE NO. 1 DEFROSTER NOZZLE GARNISH


    B134011E01
  1. Disengage the 8 clips and the 4 guides.

  1. Disconnect each connector and remove the No. 1 defroster nozzle garnish.



47. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY


    C132564E01
  1. Disconnect the connector (yellow colored one).



48. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Disengage each clamp.

  1. Disconnect each connector.

  1. Remove the bolt <J>.

  1. Remove the 2 passenger airbag bolts <K>.



  1. with Plasmacluster:



    1. Disconnect the connector.


      B134012E04

  1. Remove the 2 bolts <H> or <O>.

  1. Remove the 2 nuts <C> or <I>.



  1. Disengage the 5 claws and remove the instrument panel safety pad assembly.


    B134014E04



49. REMOVE SIDE NO. 1 DEFROSTER NOZZLE DUCT


    B134016E02
  1. Remove the screw <F> and the side No. 1 defroster nozzle duct.



50. REMOVE SIDE NO. 2 DEFROSTER NOZZLE DUCT


    B134017E02
  1. Remove the screw <F> and the side No. 2 defroster nozzle duct.



51. REMOVE DEFROSTER NOZZLE ASSEMBLY


    B134018E02
  1. Remove the 3 screws <F> and the defroster nozzle assembly.



52. REMOVE NO. 1 HEATER TO REGISTER DUCT


    B134019E02
  1. Remove the 3 screws <F> and the No. 1 heater to register duct.



53. REMOVE NO. 3 HEATER TO REGISTER DUCT


    B134020E02
  1. Remove the 3 screws <F> and the No. 3 heater to register duct.



54. REMOVE NO. 2 HEATER TO REGISTER DUCT


    B134021E02
  1. Remove the 2 screws <F> and the No. 2 heater to register duct.



55. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for LHD)


  1. Disengage the 6 clamps and clip and remove the No. 2 antenna cord sub-assembly.


    E129184E01



56. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for RHD)


  1. Disengage the 6 clamps and clip and remove the No. 2 antenna cord sub-assembly.


    E129185E01



57. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)


58. REMOVE SEAT TRACK COVER LH (for Manual Seat)
  1. Move the front seat assembly fully forward by operating the slide handle.



    B139099
  1. Using a screwdriver, disengage the 4 claws and remove the seat track cover.

    HINT:
    Tape the screwdriver tip before use.



59. REMOVE INNER SEAT TRACK BRACKET COVER LH (for Manual Seat)


    B139100
  1. Using a screwdriver, disengage the 4 claws and remove the inner seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.



60. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)
  1. Move the front seat assembly to the rearmost position by operating the slide handle.



    B139101
  1. Remove the 2 bolts on the front seat track bracket.

  1. Move the front seat assembly fully forward by operating the slide handle.



    B139102
  1. Remove the 2 bolts on the rear seat track bracket.

  1. Move the front seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and reclining adjuster release handle.

  1. Disconnect the connectors and clamp.

  1. Remove the front seat assembly.



61. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Power Seat)


62. REMOVE SEAT TRACK COVER LH (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the position farthest forward.



    B139099
  1. Using a screwdriver, detach the 4 claws and remove the seat track cover.

    HINT:
    Tape the screwdriver tip before use.



63. REMOVE SEAT TRACK COVER RH (for Power Seat)


    B139100
  1. Using a screwdriver, detach the 4 claws and remove the inner seat track bracket cover.



64. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.



    B140607
  1. Remove the 2 bolts on the front seat track bracket.

  1. Operate the power seat switch knob and move the seat to the position farthest forward.



    B139102
  1. Remove the 2 bolts on the rear seat track bracket.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).

  1. Disconnect the connectors under the seat. Then remove the front seat assembly.



65. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)


66. REMOVE SEAT TRACK COVER RH (for Manual Seat)


67. REMOVE INNER SEAT TRACK BRACKET COVER RH (for Manual Seat)


68. REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)


69. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Power Seat)


70. REMOVE SEAT TRACK COVER RH (for Power Seat)


71. REMOVE SEAT TRACK COVER LH (for Power Seat)


72. REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)


73. REMOVE REAR SEAT CUSHION ASSEMBLY


    B134699E01
  1. Detach the 2 front hooks of the seat cushion from the vehicle body.

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the step above for the other hook.

  1. Remove the seat cushion.



74. REMOVE REAR SEAT HEADREST ASSEMBLY


75. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY


76. REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    B136539
  1. Remove the 2 bolts and separate type rear seatback assembly LH.



77. REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)


    B134700
  1. Remove the 2 bolts and separate type rear seatback assembly RH.



78. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    B136561
  1. Remove the bolt and rear side seatback assembly LH.



79. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

HINT:
Use the same procedures for the RH side and LH side.



80. REMOVE REAR SEATBACK COVER (for Reclining Seat Type)


    B139075
  1. Using a screwdriver, detach the claws and remove the 2 rear seatback covers.

    NOTICE:
    1. Tape the screwdriver tip before use.
    2. Use the same procedures for the RH side and LH side.



81. REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)


    B139076E01
  1. Separate the 2 rear seat belts.



    B139081E01
  1. Disengage the 3 clamps and then separate the cover.



    B139077
  1. Remove the 2 bolts and 2 nuts and separate type rear seatback assembly LH.



82. REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Reclining Seat Type)


    B139078E01
  1. Separate the rear seat belt.



    B139082E01
  1. Disengage the 3 clamps and then separate the cover.



    B139079
  1. Remove the 2 bolts and 2 nuts and separate type rear seatback assembly RH.



83. REMOVE CENTER SEATBACK ASSEMBLY (for Reclining Seat Type)


    B139080
  1. Remove the 2 bolts and center seatback assembly.



84. REMOVE REAR DOOR SCUFF PLATE LH


    B132068
  1. Disengage the 5 claws and 2 clips, and remove the rear door scuff plate LH.



85. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


86. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.



87. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


88. REMOVE RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH (for Reclining Seat Type)


    B139083
  1. Remove the bolt.

  1. Disengage the 2 clips and the claw and then separate the reclining remote control lever sub-assembly.



    B139084
  1. Separate the rear seat reclining control cable and remove the reclining remote control lever sub-assembly.



89. REMOVE RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH (for Reclining Seat Type)


90. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    B136445E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.



91. REMOVE DOOR ASSIST GRIP COVER LH


    B149028E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the door assist grip cover.



92. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B136449
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 7 clips.



    B136450
  1. Raise the rear door trim board to disengage the 4 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.

  1. Disconnect the connector.



    B136453
  1. Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.



    B141704
  1. Disengage the clip as shown in the illustration and remove the No. 1 door scuff plate clamp from the rear door trim board.



93. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    B136456
  1. Disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.



94. REMOVE FRONT DOOR SCUFF PLATE LH


    B132067
  1. Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.



95. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B132116E01
  1. Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



96. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


97. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    B131995
  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



98. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B131996
  1. Remove the bolt and disconnect the floor end of the front seat outer belt assembly LH.



99. REMOVE LOWER CENTER PILLAR GARNISH LH


    B132057
  1. Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.



100. REMOVE UPPER CENTER PILLAR GARNISH LH


    B132059
  1. Remove the bolt.

  1. Disengage the clip and remove the upper center pillar garnish LH.



101. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.



102. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side.



103. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


104. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedures for the RH side and the LH side.



105. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side.



106. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedures for the RH side and the LH side.



107. REMOVE UPPER CENTER PILLAR GARNISH RH

HINT:
Use the same procedures for the RH side and the LH side.



108. REMOVE ROOF SIDE INNER GARNISH LH


    B132063
  1. Disengage the 5 clips and 2 claws, and remove the roof side inner garnish LH.



109. REMOVE ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedures for the RH side and the LH side.



110. REMOVE FRONT PILLAR GARNISH LH


    B132056E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish LH.

  1. Remove the clip <A> from the vehicle body.



    B132100E01
  1. Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



111. REMOVE FRONT PILLAR GARNISH RH


    B132055E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish RH.

  1. Remove the clip <A> from the vehicle body.



    B132099E01
  1. Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



112. REMOVE ROOF CONSOLE BOX ASSEMBLY


    B132064
  1. Using a moulding remover, disengage the 2 clips and 2 claws.

  1. Disconnect the connectors and remove the roof console box assembly.



113. REMOVE VISOR ASSEMBLY LH


    B132069
  1. Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.



    B132070
  1. Disengage the 2 clips and remove the visor assembly LH.



114. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side.



115. REMOVE VISOR HOLDER
  1. Turn the visor holder approximately 45°and pull it out as shown in the illustration.



  1. Disengage the 2 claws and remove the visor holder.


    B132066E01

    HINT:
    Use the same procedures for the RH side and the LH side.



116. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY


    B132061E01
  1. Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.

    HINT:
    Tape the screwdriver tip before use.



    B132062
  1. Disengage the 2 clips and remove the front assist grip sub-assembly.

    HINT:
    Use the same procedures for the RH side and the LH side.



117. REMOVE REAR ASSIST GRIP SUB-ASSEMBLY

HINT:
Use the same procedures for the rear side and the front side.



118. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)


    B132140E02
  1. Using a screwdriver, disengage the 4 claws and remove the lens cover.

    HINT:
    Tape the screwdriver tip before use.



    B132142E01
  1. Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the 2 claws <B> and remove the No. 1 room light assembly.

  1. Disconnect the room light connector.



119. REMOVE SPOT LIGHT ASSEMBLY (w/ Sliding Roof)


    B132093E01
  1. Using a screwdriver, disengage the 2 claws labeled A and 2 claws labeled B from the vehicle body.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a screwdriver, disengage the 2 claws labeled C and remove the spot light assembly from the headlining.

    HINT:
    Tape the screwdriver tip before use.



    B132095E01
  1. Using a screwdriver, disengage the 4 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Pull the light bulb holder in the direction indicated by the arrow in the illustration to detach the claw. Then remove the spot light assembly from the light bulb holder.



120. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
  1. Remove the sun roof opening trim moulding.



121. REMOVE SUNSHADE TRIM HOLDER (w/ Rear Sunshade)


    B132091
  1. Using a screwdriver, turn the pin of each sunshade trim holder 90°.



    B132143
  1. Disengage the 2 claws and remove the sunshade trim holder.



122. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
  1. Disconnect the No. 1 roof wire connector and disengage each clamp from the front pillar LH.

  1. Remove the bolt and disconnect the radio setting condenser from the front pillar RH.

  1. Disconnect the antenna cord sub-assembly connector and disengage each clamp from the front pillar RH.

  1. Disconnect the antenna cord sub-assembly connector and disengage the clamp from the rear pillar RH.



  1. Disengage the 4 clips.


    B147610E01



    B132073
  1. Remove the roof headlining assembly from the vehicle through the rear left door.



123. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
  1. Disconnect the No. 1 roof wire connector and disengage each clamp from the front pillar LH.

  1. Remove the bolt and disconnect the radio setting condenser from the front pillar RH.

  1. Disconnect the antenna cord sub-assembly connector and disengage each clamp from the front pillar RH.

  1. Disconnect the antenna cord sub-assembly connector and disengage the clamp from the rear pillar RH.

  1. Disconnect the sliding roof drive gear connector.



  1. Disengage the hook, 4 clips, and 2 fasteners.


    B147611E01



    B132074
  1. Remove the roof headlining assembly from the vehicle through the rear left door.



124. REMOVE ANTENNA CORD SUB-ASSEMBLY
  1. Peel the strips of the tape used to secure the antenna cord only to the extent that allows removal of the antenna cord.

    HINT:
    Tape is not available as a supply part. Try to leave as much tape as possible on the roof headlining so that the tape can be reused.



  1. Remove the antenna cord from the roof headlining.


    E134767E01