AUTOMATIC TRANSAXLE SYSTEM > Park / Neutral Position Switch Circuit |

| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn on the tester.
Enter the following items: "Powertrain / ECT / Data List".
According to the display on the tester, read "Data List".
| Item | Measurement Item/ Range (display) | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP Switch Status/ ON or OFF | Shift lever position is; P and N: ON Except P and N: OFF | When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (R Range) | PNP Switch Status/ ON or OFF | Shift lever position is; R: ON Except R: OFF | When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (P Range) | PNP Switch Status/ ON or OFF | Shift lever position is; P: ON Except P: OFF | When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (N Range) | PNP Switch Status/ ON or OFF | Shift lever position is; N: ON Except N: OFF | When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (D Range) | PNP Switch Status/ ON or OFF | Shift lever position is; D and S: ON Except D and S: OFF | When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Sports Mode Selection SW | Sport Mode Select Switch Status/ ON or OFF | Shift lever position is; S, "+" and "-": ON Except S, "+" and "-": OFF | - |
| 1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Shift Position | Tester Connection | Specified Condition |
| P | 1 - 3 and 4 - 9 | Below 1 Ω |
| Except P | 10 kΩ or higher | |
| R | 1 - 2 | Below 1 Ω |
| Except R | 10 kΩ or higher | |
| N | 1 - 8 and 4 - 9 | Below 1 Ω |
| Except N | 10 kΩ or higher | |
| D, S, "+" and "-" | 1 - 7 | Below 1 Ω |
| Except D, S, "+" and "-" | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT TRANSMISSION CONTROL SWITCH |
![]() |
Connect the park/neutral position switch connector.
Disconnect the transmission control switch connector of the shift lock control unit assembly.
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Shift Position | Tester Connection | Specified Condition |
| S, "+" and "-" | 3 - 7 | Below 1 Ω |
| Except S, "+" and "-" | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK ECU TERMINAL VOLTAGE (STA TERMINAL) |
![]() |
Connect the transmission control switch connector of the shift lock control unit assembly.
Measure the voltage according to the value(s) in the table below while cranking the engine.
| Tester Connection | Specified Condition |
| STA (C56-10) - Body ground | 9 to 14 V |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM) |
![]() |
Disconnect the TCM connector.
Turn the ignition switch on, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Shift Position | Tester Connection | Specified Condition |
| R | R (C56-15) - Body ground | 10 to 14 V * |
| Except R | Below 1 V | |
| D | D (C56-16) - Body ground | 10 to 14 V |
| Except D | Below 1 V |
|
| ||||
| OK | ||
| ||