AUTOMATIC TRANSAXLE UNIT > INSPECTION |
| 1. INSPECT TRANSMISSION OIL CLEANER MAGNET |
![]() |
Use the removed magnets to collect any steel chips. Examine the chips and particles in the pan and on the magnets to determine what type of wear has occurred in the transaxle:
| 2. INSPECT INPUT SHAFT SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the input shaft end play.
| 3. INSPECT NO. 2 CLUTCH DISC |
![]() |
Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.
| 4. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the bushings of the planetary sun gear.
| 5. INSPECT NO. 1 CLUTCH DISC |
![]() |
Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.
| 6. INSPECT NO. 3 BRAKE DISC |
![]() |
Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.
| 7. INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the clearance between the underdrive planetary gear and the pinion gear at 4 points.
| 8. INSPECT REAR PLANETARY SUN GEAR ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the bushing of the rear planetary sun gear sub-assembly.
| 9. INSPECT NO. 1 BRAKE DISC |
![]() |
Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.
| 10. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using vernier calipers, measure the free length of the 3 2nd brake piston return springs including the spring seats.
| 11. INSPECT ONE-WAY CLUTCH ASSEMBLY |
![]() |
Temporarily install the one-way clutch assembly to the planetary ring gear.
Rotate the one-way clutch assembly to check the rotating direction for lock or free operation.
If the one-way clutch assembly does not operate normally, replace it.
| 12. INSPECT PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the clearance between the planetary gear case and each pinion gear at points A and B.
| - | Standard Clearance |
| A point | 0.23 to 0.59 mm (0.0091 to 0.0232 in.) |
| B point | 0.16 to 0.66 mm (0.0063 to 0.02598 in.) |
| 13. INSPECT NO. 2 BRAKE DISC |
![]() |
Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.
| 14. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using vernier calipers, measure the free length of the 1st and reverse brake return spring together with the spring seat.
| 15. INSPECT CLEARANCE OF NO. 2 BRAKE |
![]() |
Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Thickness | Thickness |
| 4.0 (0.157) | 4.3 (0.169) |
| 4.1 (0.161) | 4.4 (0.173) |
| 4.2 (0.165) | - |
| 16. INSPECT CLEARANCE OF NO. 1 BRAKE |
![]() |
Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Thickness | Thickness |
| 3.0 (0.118) | 3.3 (0.130) |
| 3.1 (0.122) | 3.4 (0.134) |
| 3.2 (0.126) | 3.5 (0.138) |
| 17. INSPECT CLEARANCE OF NO. 3 BRAKE |
![]() |
Using vernier calipers and a straight edge, measure the distance shown in the illustration (Dimension A) while a load of 500 N (51 kgf, 112 lbf) is being applied to the flange.
Using vernier calipers and a straight edge, measure the distance shown in the illustration. (Dimension B).
Calculate the clearance value using the following formula:
clearance = Dimension B - Dimension A
| Thickness | Thickness |
| 3.80 (0.150) | 4.10 (0.161) |
| 3.90 (0.154) | 4.20 (0.165) |
| 4.00 (0.157) | 4.30 (0.169) |
| 18. INSPECT CLEARANCE OF NO. 1 CLUTCH DISC |
![]() |
Install the direct multiple disc clutch assembly onto the transaxle rear cover.
Using a dial indicator, measure the No. 1 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Thickness | Thickness |
| 3.0 (0.118) | 3.3 (0.130) |
| 3.1 (0.122) | 3.4 (0.134) |
| 3.2 (0.126) | 3.5 (0.138) |
| 19. INSPECT CLEARANCE OF NO. 2 CLUTCH DISC |
![]() |
Install the direct multiple disc clutch assembly onto the transaxle rear cover.
Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Thickness | Thickness |
| 3.0 (0.118) | 3.3 (0.130) |
| 3.1 (0.122) | 3.4 (0.134) |
| 3.2 (0.126) | 3.5 (0.138) |