SFI SYSTEM > ECM Power Source Circuit |

| 1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
![]() |
Disconnect the C24 ECM connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| E1 (C24-104) - Body ground | Below 1 Ω |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 2.INSPECT ENGINE ROOM J/B (EFI RELAY VOLTAGE) |
![]() |
Remove the engine room J/B from the engine room R/B.
Disconnect the 1E engine room J/B connector.
Turn the ignition switch to the ON position.
Measure the voltage between the terminals.
| Tester Connection | Specified Condition |
| 1E-12 - Body ground | 9 to 14 V |
Reconnect the engine room J/B connector.
Reinstall the engine room J/B.
|
| ||||
| NG | |
| 3.INSPECT FUSE (EFI MAIN FUSE) |
![]() |
Inspect the EFI MAIN fuse.
Remove the EFI MAIN fuse from the engine room R/B.
Measure the EFI MAIN fuse resistance.
Reinstall the EFI MAIN fuse.
|
| ||||
| OK | ||
| ||
| 4.INSPECT ENGINE ROOM J/B (EFI RELAY) |
![]() |
Remove the engine room J/B from the engine room R/B.
Inspect the EFI relay.
Measure the EFI relay resistance.
| Tester Connection | Specified Condition |
| 1E-6 - 1E-12 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-11) |
Reinstall the engine room J/B.
|
| ||||
| OK | |
| 5.INSPECT FUSE (EFI NO. 2 FUSE) |
![]() |
Inspect the EFI No. 2 fuse.
Remove the EFI No. 2 fuse from the engine room R/B.
Measure the EFI No. 2 fuse resistance.
Reinstall the EFI No. 2 fuse.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (EFI RELAY - ECM) |
![]() |
Disconnect the A24 ECM connector.
![]() |
Remove the engine room J/B from the engine room R/B.
Disconnect the 1E engine room J/B connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| +B (A24-2) - 1E-6 | Below 1 Ω |
| +B2 (A24-1) - 1E-6 | Below 1 Ω |
| Tester Connection | Specified Condition |
| +B (A24-2) or 1E-6 - Body ground | 10 kΩ or higher |
| +B2 (A24-1) or 1E-6 - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the engine room J/B connector.
Reinstall the engine room J/B.
|
| ||||
| OK | |
| 7.INSPECT ECM (IGSW VOLTAGE) |
![]() |
Disconnect the A24 and C24 ECM connectors.
Turn the ignition switch to the ON position.
Measure the voltage between the terminals of the A24 and C24 ECM connectors.
| Tester Connection | Specified Condition |
| IGSW (A24-28) - E1 (C24-104) | 9 to 14 V |
Reconnect the ECM connectors.
|
| ||||
| NG | |
| 8.INSPECT FUSE (IGN FUSE) |
![]() |
Remove the IGN fuse from the instrument panel J/B.
Measure the fuse resistance.
| Result | Proceed to |
| OK (RHD) | A |
| OK (LHD) | B |
| NG | C |
Reinstall the fuse.
|
| ||||
|
| ||||
| A | |
| 9.INSPECT IGNITION RELAY NO. 2 |
![]() |
Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1 and 2) |
Reinstall the IG2 relay.
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND) |
![]() |
Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| IG2 relay terminal 2 - Body ground | Below 1 Ω |
Reinstall the IG2 relay.
|
| ||||
| OK | |
| 11.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the E23 ignition switch connector.
Measure the resistance between the terminals.
| Tester Connection | Ignition Switch Position | Specified Condition |
| All Terminals | LOCK | 10 kΩ or higher |
| 2 - 4 | ACC | Below 1 Ω |
| 1 - 2 - 4, 5 - 6 | ON | |
| 1 - 3 - 4, 5 - 6 - 7 | START |
Reconnect the ignition switch connector.
|
| ||||
| OK | ||
| ||
| 12.CHECK HARNESS AND CONNECTOR (EFI RELAY - ECM, EFI RELAY - BODY GROUND) |
![]() |
Disconnect the A24 ECM connector.
![]() |
Remove the engine room J/B from the engine room R/B.
Disconnect the 1E engine room J/B connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| MREL (A24-44) - 1E-9 | Below 1 Ω |
| 1E-11 - Body ground | Below 1 Ω |
| Tester Connection | Specified Condition |
| MREL (A24-44) or 1E-9 - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the engine room J/B connector.
Reinstall the engine room J/B.
|
| ||||
| OK | ||
| ||