AIR CONDITIONING CONTROL ASSEMBLY > INSTALLATION |
| 1. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (w/o Radio Receiver) |
![]() |
Install the air conditioning control assembly as shown in the illustration.
| 2. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (w/ Radio Receiver) |
![]() |
Install the air conditioning control assembly as shown in the illustration.
| 3. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System) |
![]() |
Install the air conditioning control assembly as shown in the illustration.
| 4. INSTALL RADIO NO. 2 BRACKET (w/o Radio Receiver) |
![]() |
Install the radio No. 2 bracket with the 3 bolts.
| 5. INSTALL RADIO NO. 2 BRACKET (w/ Radio Receiver) |
![]() |
Install the radio No. 2 bracket with the 5 bolts.
| 6. INSTALL RADIO NO. 2 BRACKET (w/ Navigation System) |
![]() |
Install the radio No. 2 bracket with the 5 bolts.
| 7. INSTALL RADIO NO. 1 BRACKET (w/o Radio Receiver) |
![]() |
Install the radio No. 1 bracket with the 3 bolts.
| 8. INSTALL RADIO NO. 1 BRACKET (w/ Radio Receiver) |
![]() |
Install the radio No. 1 bracket with the 5 bolts.
| 9. INSTALL RADIO NO. 1 BRACKET (w/ Navigation System) |
![]() |
Install the radio No. 1 bracket with the 5 bolts.
| 10. INSTALL RADIO TUNER OPENING COVER WITH HEATER CONTROL PANEL ASSEMBLY (w/o Radio Receiver) |
Connect the connector.
![]() |
Engage the 6 clips.
Install the radio tuner opening cover with heater control panel assembly with the 4 bolts <N>.
| 11. INSTALL RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Radio Receiver) |
![]() |
Connect each connector.
Engage the 4 clips.
Install the radio receiver with heater control panel assembly with the 4 bolts.
| 12. INSTALL NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System) |
Connect each connector.
![]() |
Engage the 4 clips.
Install the navigation receiver with heater control panel assembly with the 4 bolts.
| 13. INSTALL INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY |
Connect the connector.
![]() |
Engage the 7 clips and install the instrument panel No. 2 register assembly.
| 14. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
Connect each connector.
![]() |
Engage the 4 claws.
Install the upper console panel sub-assembly with the 2 screws <F>.
| 15. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Connect the connector.
Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.
| 16. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.
| 17. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle) |
with Seat Heater System:
Connect each connector.
![]() |
Engage the 6 claws and the 3 clips to install the floor shift position indicator housing sub-assembly.
| 18. INSTALL UPPER CONSOLE PANEL (for Manual Transaxle) |
![]() |
Engage the 2 claws and the 5 clips to install the upper console panel as shown in the illustration.
| 19. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.
| 20. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.
| 21. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Install the shift lever knob sub-assembly.
| 22. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Install the shift lever knob sub-assembly.
| 23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |