AIR CONDITIONING CONTROL ASSEMBLY > REMOVAL |
| 1. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 3. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.
| 4. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.
| 5. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Disengage the 6 claws and the 3 clips, and then remove the floor shift position indicator housing sub-assembly.
with Seat Heater System:
Disconnect each connector.
| 6. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle) |
![]() |
Open the lid of the upper console panel.
Apply protective tape to the area shown in the illustration.
![]() |
Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.
| 7. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Disengage the 3 claws and the 5 clips.
Disengage the clamp.
Disconnect the connector and remove the upper console rear panel sub-assembly.
| 8. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.
| 9. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY |
![]() |
Remove the 2 screws <F>.
Disengage the 4 claws.
Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.
| 10. REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY |
![]() |
Apply protective tape to the areas shown in the illustration.
![]() |
Using a moulding remover, disengage the 3 clips.
![]() |
Using a moulding remover, disengage the 4 clips.
Disconnect the connector and remove the instrument panel No. 2 register assembly.
| 11. REMOVE RADIO TUNER OPENING COVER WITH HEATER CONTROL PANEL ASSEMBLY (w/o Radio Receiver) |
![]() |
Remove the 4 bolts <N>.
Disengage the 6 clips and remove the radio tuner opening cover with heater control panel assembly.
Disconnect the connector.
| 12. REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Radio Receiver) |
![]() |
Remove the 4 bolts.
Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the radio receiver with heater control panel assembly.
| 13. REMOVE RADIO NO. 1 BRACKET (w/o Radio Receiver) |
![]() |
Remove the 3 bolts and radio No. 1 bracket.
| 14. REMOVE RADIO NO. 1 BRACKET (w/ Radio Receiver) |
![]() |
Remove the 5 bolts and radio No. 1 bracket.
| 15. REMOVE RADIO NO. 2 BRACKET (w/o Radio Receiver) |
![]() |
Remove the 3 bolts and radio No. 2 bracket.
| 16. REMOVE RADIO NO. 2 BRACKET (w/ Radio Receiver) |
![]() |
Remove the 5 bolts and radio No. 2 bracket.
| 17. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/o Radio Receiver) |
![]() |
Remove the air conditioning control assembly as shown in the illustration.
| 18. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/ Radio Receiver) |
![]() |
Remove the air conditioning control assembly as shown in the illustration.