Home › BODY › EXTERIOR › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT BUMPER SIDE RETAINER LH


    B137727
  1. Engage the claw and install the front bumper side retainer LH.

  1. Install the screw.



2. INSTALL FRONT BUMPER SIDE RETAINER RH


3. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    B197129
  1. Install the front bumper reinforcement sub-assembly with the 6 bolts.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }

  1. Engage each clamp.



4. INSTALL FRONT BUMPER ENERGY ABSORBER


    B137728
  1. Install the front bumper energy absorber to the front bumper reinforcement sub-assembly.



5. INSTALL RADIATOR GRILLE EMBLEM


    B137235
  1. Engage the 4 claws to install the radiator grille emblem.



6. INSTALL FRONT BUMPER UPPER RETAINER


    B137234
  1. Install the front bumper upper retainer with the 3 clips.



7. INSTALL HOOD TO FRONT END PANEL SEAL


    B137233
  1. Apply new double-sided tape to the hood to front end panel seal.

  1. Remove the release paper from the hood to front end panel seal.

  1. Install the hood to front end panel seal with the 10 clips.



8. INSTALL RADIATOR GRILLE


    B137232
  1. Engage the 16 claws and install the radiator grille.

  1. Install the 2 screws.



9. INSTALL LOWER RADIATOR GRILLE


    B137731
  1. Engage the 14 claws to install the lower radiator grille.



10. INSTALL FRONT BUMPER HOLE COVER LH


    B137733
  1. Engage the 5 claws to install the front bumper hole cover LH.



11. INSTALL FRONT BUMPER HOLE COVER RH


12. INSTALL FOG LIGHT ASSEMBLY LH


    E128199
  1. Install the fog light assembly with the screw.

    Torque:
    1.6 N*m{ 16 kgf*cm , 14 in.*lbf }



13. INSTALL FOG LIGHT ASSEMBLY RH


14. INSTALL FRONT BUMPER LOWER COVER


    B137730
  1. Engage the 2 claws to install the front bumper lower cover.



15. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET


    B137742
  1. Engage the 2 claws and install the front bumper extension mounting bracket.

  1. Install the 2 screws.



16. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)


    E163886
  1. Engage the 2 claws and install the No. 1 ultrasonic sensor.



    E163885
  1. Connect the connector.



17. INSTALL NO. 2 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)


  1. Engage the 6 clamps and install the No. 2 engine room wire.


    B189098E01

  1. Using 2 new pieces of adhesive tape, secure the No. 2 engine room wire as follows:

    1. Route the No. 2 engine room wire along the front bumper with the 2 pieces of marking tape positioned as shown in the illustration.

      NOTICE:
      Do not strain the No. 2 engine room wire.

    2. Attach a piece of adhesive tape over each marking tape position to secure the No. 2 engine room wire.



18. INSTALL HEADLIGHT CLEANER WASHER HOSE (w/ Headlight Cleaner System)


19. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    E128842
  1. Engage the 2 claws.



    E128841
  1. Install the headlight washer actuator sub-assembly with the bolt.

  1. Connect the headlight washer hose.



20. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)


21. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    E128840
  1. Engage the 2 claws and install the headlight washer nozzle sub-assembly.



22. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)