Home › BODY › EXTERIOR › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT BUMPER SIDE RETAINER LH


    B137727
  1. Engage the claw and install the front bumper side retainer LH.

  1. Install the screw.



2. INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:
Use the same procedure for the RH side and LH side.



3. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    B220951
  1. Install the front bumper reinforcement sub-assembly with the 6 bolts.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }

  1. Engage 6 clamps.



4. INSTALL FRONT BUMPER ENERGY ABSORBER


    B220950
  1. Engage the 2 guides and install the front bumper energy absorber to the front bumper reinforcement sub-assembly.



5. INSTALL RADIATOR GRILLE EMBLEM


    B137235
  1. Engage the 4 claws to install the radiator grille emblem.



6. INSTALL FRONT BUMPER UPPER RETAINER


    B137234
  1. Install the front bumper upper retainer with the 3 clips.



7. INSTALL HOOD TO FRONT END PANEL SEAL


    B137233
  1. Apply new double-sided tape to the hood to front end panel seal.

  1. Remove the release paper from the hood to front end panel seal.

  1. Install the hood to front end panel seal with the 10 clips.



8. INSTALL RADIATOR GRILLE


    B225459
  1. Engage the 15 claws and install the radiator grille.

  1. Install the 2 screws.



9. INSTALL LOWER RADIATOR GRILLE


    B137731
  1. Engage the 14 claws to install the lower radiator grille.



10. INSTALL FRONT BUMPER HOLE COVER LH


    B220948
  1. Engage the 5 claws and install the front bumper hole cover LH.



11. INSTALL FOG LIGHT ASSEMBLY LH


    E128199
  1. Install the fog light assembly with the screw.

    Torque:
    1.6 N*m{ 16 kgf*cm , 14 in.*lbf }



12. INSTALL FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure for the RH side and LH side.



13. INSTALL FOG LIGHT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



14. INSTALL FRONT BUMPER LOWER COVER


    B226380
  1. Engage the 2 claws to install the front bumper lower cover.



15. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET


    B137742
  1. Engage the 2 claws and install the front bumper extension mounting bracket.

  1. Install the 2 screws.



16. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)


    E134855E01
  1. Install the No. 1 ultrasonic sensor retainer to the front bumper.

    NOTICE:
    Do not damage the bumper with the snap when installing the retainer.

    HINT:
    1. When installing the retainer, align the keyhole and snap as shown in the illustration.
    2. The illustration is for the LH side. The RH side is the opposite of the LH side.



17. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)


    E135368
  1. Engage the 2 claws and install the No. 1 ultrasonic sensor.

    HINT:
    The illustration is for the LH side. The RH side is the opposite of the LH side.

  1. Connect the sensor connector.



18. INSTALL HEADLIGHT CLEANER WASHER HOSE (w/ Headlight Cleaner System)


  1. Engage the 5 clamps and install the headlight cleaner washer hose.


    B137738



19. INSTALL HEADLIGHT CLEANER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

NOTICE:
Check that no water or foreign matter such as dirt is around the joint of the headlight cleaner actuator sub-assembly or the headlight cleaner nozzle.



    E182204
  1. Engage the 2 claws.



    E182203
  1. Install the headlight cleaner actuator sub-assembly with the bolt.

  1. Connect the headlight washer hose.



    E183136
  1. Engage the 2 claws to install the headlight cleaner nozzle sub-assembly to the nozzle holder.

    NOTICE:
    Assemble the headlight cleaner nozzle holder and the headlight cleaner nozzle sub-assembly in the correct direction. Attempting to assemble them in the wrong direction may cause damage to the headlight cleaner nozzle sub-assembly.



    E149521
  1. Engage the claw to install the headlight cleaner nozzle with nozzle holder to the headlight cleaner actuator sub-assembly as shown in the illustration.

    NOTICE:
    Gently pull out the headlight cleaner nozzle to confirm that the nozzle is firmly engaged to the headlight cleaner actuator sub-assembly.



20. INSTALL HEADLIGHT CLEANER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure for the RH side and LH side.