DTC B1608/84 Front Satellite Sensor Bus LH Initialization Incomplete |
DTC B1617/84 Lost Communication with Front Airbag Sensor LH |
DTC B1618/84 Front Airbag Sensor LH Initialization Incomplete |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1608/84 B1617/84 B1618/84 |
|
|

| 1.CHECK DTC |
![]() |
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1608, B1618, or 84 is output. | A |
| DTC B1613/83 is output. | B |
| DTC B1608, B1618, or 84 and B1613/83 are not output. | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and front airbag sensor LH.
Check that the connectors (on the center airbag sensor assembly side and front airbag sensor LH side) are not damaged.
|
| ||||
| OK | |
| 4.CHECK FRONT AIRBAG SENSOR LH (OPEN) |
![]() |
Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A13-2 (+SL) - A13-1 (-SL) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK FRONT AIRBAG SENSOR LH (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A13-2 (+SL) - A13-1 (-SL) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK FRONT AIRBAG SENSOR LH (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A13-2 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| A13-1 (-SL) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK FRONT AIRBAG SENSOR LH (SHORT TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A13-2 (+SL) - Body ground | Always | 1 MΩ or higher |
| A13-1 (-SL) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 8.CHECK FRONT AIRBAG SENSOR LH |
![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the front airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1608, B1617, B1618, or 84 is output. | A |
| DTC B1603, B1612, B1613, or 83 is output. | B |
| DTC B1603, B1612, B1613, or 83 and B1608, B1617, B1618, or 84 are not output. | C |
|
| ||||
|
| ||||
| C | ||
| ||
| 9.CHECK INSTRUMENT PANEL WIRE (OPEN) |
![]() |
Disconnect the instrument panel wire connector from the engine room main wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AE4-3 (+SL) - AE4-4 (-SL) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 10.CHECK INSTRUMENT PANEL WIRE (SHORT) |
![]() |
Disconnect the instrument panel wire connector from the engine room main wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AE4-3 (+SL) - AE4-4 (-SL) | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 11.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the instrument panel wire connector from the engine room main wire.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AE4-3 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| AE4-4 (-SL) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||
| 12.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) |
![]() |
Disconnect the instrument panel wire connector from the engine room main wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AE4-3 (+SL) - Body ground | Always | 1 MΩ or higher |
| AE4-4 (-SL) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||