COMPRESSOR AND MAGNETIC CLUTCH (for 2GR-FE) > INSTALLATION |
| 1. INSTALL COMPRESSOR AND MAGNETIC CLUTCH |
![]() |
Install the compressor and magnetic clutch with the 4 bolts.
| 2. INSTALL NO. 1 COOLER REFRIGERANT SUCTION HOSE |
![]() |
Remove the attached vinyl tape from the hose.
Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnetic clutch.
Install the O-ring onto the No. 1 cooler refrigerant suction hose.
Install the No. 1 cooler refrigerant suction hose onto the compressor and magnetic clutch with the bolt.
| 3. INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
![]() |
Remove the attached vinyl tape from the hose.
Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnetic clutch.
Install the O-ring onto the No. 1 cooler refrigerant discharge hose sub-assembly.
Install the No. 1 cooler refrigerant discharge hose onto the compressor and magnetic clutch with the bolt.
| 4. INSTALL PIPING CLAMP |
![]() |
Install the piping clamp to the No. 1 cooler refrigerant suction hose and No. 1 cooler refrigerant discharge hose.
| 5. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the bracket with the bolt.
![]() |
Install the wire harness clamp stay with the bolt.
![]() |
Connect the wire harness clamp.
Install the generator assembly to the cylinder block with the bolt.
![]() |
Install the 2 bolts.
![]() |
Connect the generator connector to the generator assembly.
Install the generator wire with the nut.
Install the terminal cap.
Connect the 2 wire harness clamps.
Connect the magnetic clutch connector to the compressor and magnetic clutch.
| 6. INSTALL V-RIBBED BELT |
![]() |
Install the V-ribbed belt.
Using SST, turn the belt tensioner counterclockwise and remove the bar.
![]() |
If it is difficult to install the V-ribbed belt, perform the following procedure:
Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.
While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the tensioner pulley.
After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the belt has not slipped out of the grooves on the bottom of the crank pulley by hand.
| 7. INSTALL RADIATOR ASSEMBLY |
![]() |
Install the radiator to the body.
![]() |
Install the condenser assembly with the 4 bolts.
| 8. INSTALL FAN SHROUD |
![]() |
Install the fan assembly with motor to the radiator with the 2 guides at the bottom and 3 snap fits on the top.
![]() |
Connect the fan motor connector.
| 9. INSTALL RADIATOR SUPPORT UPPER |
![]() |
Install the radiator support upper with the 5 bolts.
![]() |
Install the hood lock assembly to the radiator support upper with the 3 bolts.
![]() |
For LHD:
Install the hood lock control cable assembly to the radiator support upper with the clamp.
![]() |
For RHD:
Install the hood lock control cable assembly to the radiator support upper with the clamp.
Connect the 2 horn connectors.
| 10. CONNECT NO. 1 OIL COOLER OUTLET TUBE (for Automatic Transaxle) |
![]() |
Connect the No. 1 oil cooler outlet tube to the radiator assembly.
| 11. CONNECT NO. 1 OIL COOLER INLET TUBE (for Automatic Transaxle) |
![]() |
Connect the No. 1 oil cooler inlet tube to the radiator assembly.
| 12. CONNECT RADIATOR OUTLET HOSE |
![]() |
Connect the radiator hose outlet to the radiator assembly.
| 13. CONNECT RADIATOR INLET HOSE |
![]() |
Connect the radiator hose inlet to the radiator assembly.
| 14. CONNECT RADIATOR RESERVE TANK HOSE |
![]() |
Connect the radiator reservoir tank hose to the radiator assembly.
| 15. INSTALL FRONT BUMPER ENERGY ABSORBER |
![]() |
Engage the 2 guides and install the front bumper energy absorber to the front bumper reinforcement sub-assembly.
| 16. INSTALL FRONT BUMPER ASSEMBLY |
w/ Headlight Cleaner System:
![]() |
Connect the headlight cleaner washer hose.
Connect each connector.
w/ TOYOTA Parking Assist-sensor System:
Connect the No. 1 ultrasonic sensor connector and engage the clamp.
![]() |
Engage the 2 claws.
![]() |
Install the front bumper assembly with the 8 screws, 2 clips, 2 radiator grille protectors and bolt.
![]() |
Install the pin hold clip.
![]() |
Remove the applied protective tape on the front bumper assembly.
| 17. INSTALL NO. 1 AIR CLEANER INLET |
![]() |
Install the No. 1 air cleaner inlet with the bolt.
| 18. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Install the air cleaner cap sub-assembly, and connect the 3 bands.
![]() |
Connect the mass air flow meter connector (*1).
Connect the No. 2 ventilation hose (*2).
Connect the hose band (*3).
![]() |
Connect the 3 vacuum hoses.
| 19. INSTALL AIR CLEANER INLET ASSEMBLY |
![]() |
Install the air cleaner inlet with the clamp and 2 bolts.
| 20. CONNECT BATTERY NEGATIVE TERMINAL |
| 21. ADD ENGINE COOLANT |
Close the radiator drain cock plug and 2 cylinder block drain cock plugs.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reservoir tank cap.
Start the engine, and warm it up.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the FULL line on the radiator reservoir.
| 22. CHECK FOR ENGINE COOLANT LEAKS |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 23. CHARGE WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump.
Charge with refrigerant HFC-134a (R134a).

| 24. WARM UP ENGINE |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 25. CHECK FOR REFRIGERANT LEAKS |
After recharging with refrigerant gas, check for leakage of refrigerant gas using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a gas leak detector, check for leakage from the refrigerant lines.
![]() |
Bring the gas leak detector close to the drain hose with the detector's power off, and then turn the detector on.
If a gas leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.
| 26. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Engage the 3 retainers to install the V-bank cover.
| 27. INSTALL COOL AIR INTAKE DUCT SEAL |
![]() |
Install the intake duct seal with the 7 clips.
| 28. INSTALL ENGINE UNDER COVER RH |
| 29. INSTALL ENGINE UNDER COVER LH |
| 30. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH |
| 31. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH |
| 32. INSTALL FRONT FENDER APRON SEAL RH |
| 33. INSTALL FRONT WHEEL RH |
| 34. VEHICLE PREPARATION FOR FOG LIGHT AIMING (w/ Fog Light) |
Prepare the vehicle:
| 35. PREPARATION FOR FOG LIGHT AIMING (w/ Fog Light) |
![]() |
Prepare the vehicle:
Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.
Draw a vertical line down the center of screen (V line).
Set the screen as shown in the illustration.

![]() |
Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
H Line (Fog light height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the low-beam fog lights.
V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
Draw two vertical lines so that they intersect the H line at each center mark.
| 36. FOG LIGHT AIMING INSPECTION (w/ Fog Light) |
Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.
Start the engine.
Turn on the fog light and check if the cut off line falls within the specified area in the following illustration.

| 37. FOG LIGHT AIMING ADJUSTMENT (w/ Fog Light) |
![]() |
Adjust the aim vertically:
Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.