COMPRESSOR AND MAGNETIC CLUTCH (for 2GR-FE) > REMOVAL |
| 1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM |
Start up the engine.
Turn the A/C switch on.
Operate the cooler compressor at an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.
Stop the engine.
Recover the refrigerant from the A/C system using a refrigerant recovery unit.
| 2. DISCONNECT BATTERY NEGATIVE TERMINAL |
| 3. REMOVE FRONT WHEEL RH |
| 4. REMOVE FRONT FENDER APRON SEAL RH |
| 5. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH |
| 6. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH |
| 7. REMOVE ENGINE UNDER COVER RH |
| 8. REMOVE ENGINE UNDER COVER LH |
| 9. DRAIN ENGINE COOLANT |
Remove the radiator cap sub-assembly from the radiator assembly.
Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs, then drain the coolant.

| 10. REMOVE COOL AIR INTAKE DUCT SEAL |
![]() |
Remove the 7 clips and intake duct seal.
| 11. REMOVE V-BANK COVER SUB-ASSEMBLY |
![]() |
Hold the front of the V-bank cover and raise it to disengage the 2 retainers on the front of the cover. Continue to raise the cover to disengage the retainer on the rear of the cover and remove the cover.
| 12. REMOVE AIR CLEANER INLET ASSEMBLY |
![]() |
Remove the 2 bolts, clamp and air cleaner inlet.
| 13. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the 3 vacuum hoses.
![]() |
Disconnect the mass air flow meter connector (*1).
Disconnect the No. 2 ventilation hose (*2).
Disconnect the hose band (*3).
![]() |
Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.
| 14. REMOVE NO. 1 AIR CLEANER INLET |
![]() |
Remove the bolt and No. 1 air cleaner inlet.
| 15. REMOVE FRONT BUMPER ASSEMBLY |
![]() |
Put protective tape around the front bumper assembly.
![]() |
Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
![]() |
Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.
![]() |
Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.
Disconnect each connector.
w/ TOYOTA Parking Assist-sensor System:
Disengage the clamp and disconnect the No. 1 ultrasonic sensor connector.
w/ Headlight Cleaner System:
Disconnect the headlight cleaner washer hose.
![]() |
Remove the front bumper assembly.
| 16. REMOVE FRONT BUMPER ENERGY ABSORBER |
![]() |
Disengage the 2 guides and remove the front bumper energy absorber from the front bumper reinforcement sub-assembly.
| 17. SEPARATE RADIATOR RESERVE TANK HOSE |
![]() |
Separate the radiator reserve tank hose from the radiator assembly.
| 18. DISCONNECT RADIATOR INLET HOSE |
![]() |
Separate the radiator inlet hose from the radiator assembly.
| 19. DISCONNECT RADIATOR OUTLET HOSE |
![]() |
Separate the radiator outlet hose from the radiator assembly.
| 20. DISCONNECT NO. 1 OIL COOLER INLET HOSE (for Automatic Transaxle) |
![]() |
Separate the No. 1 oil cooler inlet hose from the radiator assembly.
| 21. DISCONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transaxle) |
![]() |
Separate the No. 1 oil cooler outlet hose from the radiator assembly.
| 22. REMOVE RADIATOR SUPPORT UPPER |
Disconnect the horn connector.
![]() |
Remove the 3 bolts and separate the hood lock assembly from the radiator support upper.
![]() |
For LHD:
Remove the clamp and separate the hood lock control cable from the radiator support upper.
![]() |
For RHD:
Remove the clamp and separate the hood lock control cable from the radiator support upper.
![]() |
Remove the 5 bolts and radiator support upper.
| 23. REMOVE FAN SHROUD |
![]() |
Remove the 3 clamps and connector.
![]() |
Release the 3 snap fits and lift the fan assembly with motor from the radiator.
| 24. REMOVE RADIATOR ASSEMBLY |
![]() |
Remove the 4 bolts and separate the condenser assembly from the radiator assembly.
![]() |
Remove the radiator assembly from the body.
| 25. REMOVE V-RIBBED BELT |
![]() |
Using SST, release the belt tension by turning the belt tensioner counterclockwise, and remove the V-ribbed belt from the belt tensioner.
![]() |
While turning the belt tensioner counterclockwise, align with its holes, and then insert the 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner.
| 26. REMOVE GENERATOR ASSEMBLY |
![]() |
Remove the terminal cap.
Remove the nut and disconnect the wire harness from terminal B.
Disconnect the generator connector from the generator assembly.
Disconnect the connector from the compressor and magnetic clutch.
Disconnect the 2 wire harness clamps.
![]() |
Remove the 2 bolts.
![]() |
Remove the bolt from the cylinder block.
Disconnect the wire harness clamp and remove the generator assembly.
![]() |
Remove the bolt and wire harness clamp stay.
![]() |
Remove the bolt and bracket.
| 27. REMOVE PIPING CLAMP |
![]() |
Remove the piping clamp from the No. 1 cooler refrigerant discharge hose and No. 1 cooler refrigerant suction hose.
| 28. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
![]() |
Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the compressor.
Remove the O-ring from the discharge hose sub-assembly.
| 29. DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE |
![]() |
Remove the bolt and disconnect the No. 1 cooler refrigerant suction hose from the compressor.
Remove the O-ring from the cooler refrigerant suction hose.
| 30. REMOVE COMPRESSOR AND MAGNETIC CLUTCH |
![]() |
Disconnect the magnetic clutch connector.
Remove the 4 bolts.
Remove the compressor and magnetic clutch.