DIFFERENTIAL CASE > REASSEMBLY |
| 1. INSTALL DIFFERENTIAL SIDE GEAR |
![]() |
Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF and install them to the differential case.
| 2. INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT |
![]() |
Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.
| 3. INSPECT DIFFERENTIAL SIDE GEAR BACKLASH |
![]() |
Hold the differential case in a vise between aluminum plates.
Place a dial indicator on the tip of the side gear tooth at a right angle.
Hold the pinion gear in the differential case and measure the backlash of the side gear.
| Thickness | Thickness |
| 1.50 mm (0.0591 in.) | 1.75 mm (0.0689 in.) |
| 1.55 mm (0.0610 in.) | 1.80 mm (0.0709 in.) |
| 1.60 mm (0.0630 in.) | 1.85 mm (0.07283 in.) |
| 1.65 mm (0.0650 in.) | 1.90 mm (0.07480 in.) |
| 1.70 mm (0.0669 in.) | - |
| 4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN |
![]() |
Using a pin punch (3 mm) and hammer, install the pinion shaft straight pin.
![]() |
Using a chisel and hammer, stake the differential case.
| 5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
![]() |
Using SST and a press, install the front differential case rear tapered roller bearing to the differential case.
![]() |
Using SST and a hammer, install the front differential case rear tapered roller bearing outer race to the transaxle case.
| 6. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a press, install the front differential case front tapered roller bearing to the differential case.
Install the shim to the transaxle housing.
![]() |
Using SST and a hammer, install the front differential case front tapered roller bearing outer race to the transaxle housing.
| 7. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD |
![]() |
Install the differential assembly to the transaxle case.
Clean the contact surfaces of the transaxle case and transaxle housing.
![]() |
Install the transaxle housing to the transaxle case with the 20 bolts.
![]() |
Using SST, turn the differential assembly right and left 2 or 3 times to settle the bearing.
Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.
| Thickness | Thickness | Thickness | Thickness |
| 2.000 (0.0787) | 2.225 (0.0876) | 2.450 (0.0965) | 2.675 (0.1054) |
| 2.025 (0.0797) | 2.250 (0.0886) | 2.475 (0.0974) | 2.700 (0.1063) |
| 2.050 (0.0807) | 2.275 (0.0896) | 2.500 (0.0984) | 2.725 (0.1073) |
| 2.075 (0.0817) | 2.300 (0.0906) | 2.525 (0.0994) | 2.750 (0.1083) |
| 2.100 (0.0827) | 2.325 (0.0915) | 2.550 (0.1004) | 2.775 (0.1093) |
| 2.125 (0.0837) | 2.350 (0.0925) | 2.575 (0.1014) | 2.800 (0.1102) |
| 2.150 (0.0847) | 2.375 (0.0935) | 2.600 (0.1024) | 2.825 (0.1112) |
| 2.175 (0.0856) | 2.400 (0.0945) | 2.625 (0.1034) | 2.850 (0.1122) |
| 2.200 (0.0866) | 2.425 (0.0955) | 2.650 (0.1043) | 2.875 (0.1132) |
![]() |
Remove the 20 bolts and the transaxle housing from the transaxle case.
![]() |
Remove the differential assembly from the transaxle case.
| 8. INSTALL FRONT DIFFERENTIAL RING GEAR |
![]() |
Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).
Clean the contact surface of the front differential case.
![]() |
Align the matchmarks, and install the front differential ring gear case quickly.
![]() |
Tighten the 12 bolts.
| 9. INSTALL TRANSAXLE CASE OIL SEAL |
Coat the lip of a new oil seal with MP grease.
![]() |
Using SST and a hammer, install the oil seal.
| 10. INSTALL FRONT TRANSAXLE CASE OIL SEAL |
Coat the lip of a new oil seal with MP grease.
![]() |
Using SST and a hammer, install the oil seal.