DTC P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) |
DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |


| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2237 | Open in the circuit between terminals AF+ and AF- of the AF sensor while engine is running (2 trip detection logic) |
|
| P2238 | Any of the following conditions are met (2 trip detection logic)
|
|
| P2239 | AF+ voltage more than 4.5 V (2 trip detection logic) |
|
| P2252 | AF- voltage 0.5 V or less (2 trip detection logic) |
|
| P2253 | AF- voltage more than 4.5 V (2 trip detection logic) |
|

| Tester Display (Sensor) | Injection Volume | Status | Voltages |
| AFS B1 S1 (A/F) | +25 % | Rich | Less than 3.0 |
| -12.5 % | Lean | More than 3.35 | |
| O2S B1 S2 (HO2) | +25 % | Rich | More than 0.5 |
| -12.5 % | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Areas | ||
| 1 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.5 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.5 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the C15 A/F sensor connector.
Disconnect the C24 ECM connector.
Measure the resistance between the terminals of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A1A+ (C15-3) - A1A+ (C24-112) | Below 1 Ω |
| A1A- (C15-4) - A1A- (C24-113) | Below 1 Ω |
| Tester Connection | Specified Condition |
| A1A+ (C15-3) or A1A+ (C24-112) - Body ground | 10 kΩ or higher |
| A1A- (C15-4) or A1A- (C24-113) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.

|
| ||||
| OK | |
| 2.REPLACE AIR-FUEL RATIO SENSOR |
| NEXT | |
| 3.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 5 minutes or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2237, P2238, P2239, P2252 or P2253 | B |
|
| ||||
| A | ||
| ||