Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW REGULATOR MOTOR

POWER WINDOW REGULATOR MOTOR > REMOVAL

for Preparation Click here



1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    B132833
  1. Disengage the 2 clips and remove the front door lower frame bracket garnish.



2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B132834E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.



3. REMOVE ASSIST GRIP COVER


    B132836E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the assist grip cover.



4. REMOVE COURTESY LIGHT ASSEMBLY


    B132838E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.

  1. Disconnect the connector.



5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B132840E01
  1. Remove the 3 screws and clip (A).

  1. Using a clip remover, disengage the 9 clips.



    B136401E01
  1. Pull up the front door trim board in the direction indicated by the arrow.

  1. Disengage the reference bosses from the front door panel.

  1. Raise the front door trim board to disengage the 4 claws and remove the front door trim board together with the front door inner glass weatherstrip.



    B136403
  1. Disengage the 2 claws and disconnect the front door inside handle sub-assembly.



6. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B136408
  1. Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door inside handle sub-assembly.



7. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    B136404
  1. Using a screwdriver, disengage the 4 clips as shown in the illustration and remove the front door inner glass weatherstrip from the front door trim board.



8. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    E129164
  1. Disconnect the connector.

  1. Remove the 4 bolts and front No. 1 speaker assembly.

    NOTICE:
    Do not touch the cone part of the speaker.



9. REMOVE FRONT DOOR SERVICE HOLE COVER


    B136410E01
  1. Disconnect the connector and each clamp, and remove the front door service hole cover.

    HINT:
    Remove the remaining butyl tape on the door side.



10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the front power window regulator motor assembly connector.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.



    B136412
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, the door glass may fall, causing damage.



    B136413E01
  1. Remove the front door glass sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.

  1. Disconnect the power window regulator master switch assembly and front power window regulator motor assembly connector.



11. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY


    B136415E01
  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall, causing damage.

  1. Remove the 5 bolts.

  1. Remove the front door window regulator sub-assembly and the power window regulator motor assembly front as a unit.

  1. Remove the temporary bolt from the front door window regulator sub-assembly.



12. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B136416
  1. Using a "TORX" driver (T25), remove the 3 screws and the front power window regulator motor assembly.



13. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B136445E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.



14. REMOVE DOOR ASSIST GRIP COVER


    B149028E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the door assist grip cover.



15. REMOVE REAR ASH RECEPTACLE ASSEMBLY


    B136442
  1. Remove the rear ash receptacle assembly.



16. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B136449
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 7 clips.



    B136450
  1. Raise the rear door trim board to disengage the 4 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.

  1. Disconnect the connector.



    B136453
  1. Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.



    B141704
  1. Disengage the clip as shown in the illustration and remove the No. 1 door scuff plate clamp from the rear door trim board.



17. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    B136459
  1. Disconnect the cables and remove the rear door inside handle sub-assembly.



18. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    B136456
  1. Disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.



19. REMOVE REAR DOOR SERVICE HOLE COVER


    B136461
  1. Disconnect the connector.

  1. Remove the rear door service hole cover.

    HINT:
    Remove the remaining tape on the door side.



20. REMOVE REAR DOOR GLASS RUN


    B136466
  1. Remove the rear door glass run.



21. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    B136467
  1. Remove the 2 bolts, the screw, and the rear door lower window frame sub-assembly.



22. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B136468
  1. Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.



23. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B136470
  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



24. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    B136472E01
  1. Disconnect the connector.

  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall, causing damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.

  1. Remove the temporary bolt from the rear door window regulator.



25. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B124520
  1. Using a "TORX" driver (T25), remove the 3 screws and the rear power window regulator motor assembly.