LIGHTING SYSTEM > TERMINALS OF ECU |
| CHECK MAIN BODY ECU (INSTRUMENT PANEL J/B) |

Disconnect the IA, ID, IF and IM J/B connectors.
Measure the voltage and resistance between the specified terminals of the wire harness side connectors and body ground.
| Symbols | Wiring Color | Terminal Description | Condition | Specified Condition |
| IA-1 - Body ground | B - Body ground | Battery power supply | Always | 10 to 14 V |
| ALTB (ID-15) - Body ground | W - Body ground | Generator power supply | Always | 10 to 14 V |
| Symbols | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND1 (IF-10) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| GND2 (IM-9) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the IA, ID, IF, and IM J/B connectors.
Measure the resistance and voltage between the specified terminals of the J/B connectors and body ground.
| Symbols | Wiring Color | Terminal Description | Condition | Specified Condition |
| CLTE (E6-18) - Body ground | BR - Body ground | Automatic light control sensor ground | Always | Below 1 Ω |
| Symbols | Wiring Color | Terminal Description | Condition | Specified Condition |
| HRLY (ID-3) - Body ground | P - Body ground | Headlight relay drive output | Light control switch in HEAD | Below 1 V |
| Light control switch not in HEAD | 10 to 14 V | |||
| DIM (ID-9) - Body ground | V - Body ground | High beam headlight relays drive output | Dimmer switch in HIGH or HIGH FLASH | Below 1 V |
| Dimmer switch in LOW | 10 to 14 V | |||
| HU (IG-5) - Body ground | LG - Body ground | Dimmer switch HIGH input | Dimmer switch in HIGH | 10 to 14 V |
| Dimmer switch in LOW | Below 1 V | |||
| ILE (II-10) - Body ground | BR - Body ground | Interior light and ignition key cylinder light drive output | Interior light and ignition key cylinder light ON | Below 1 V |
| Interior light and ignition key cylinder light OFF | 10 to 14 V | |||
| LCTY (IO-7) - Body ground | LG - Body ground | Rear left door courtesy switch input | Rear left door open | Below 1 V |
| Rear left door closed | 10 to 14 V | |||
| LSWL (IP-5) - Body ground (*5) | GR - Body ground | Rear left door lock position switch input | Rear left door locked | 10 to 14 V |
| Rear left door unlocked | Below 1 V | |||
| RCTY (E6-5) - Body ground (*4) | GR - Body ground | Rear right door courtesy switch input | Rear right door open | Below 1 V |
| Rear right door closed | 10 to 14 V | |||
| LSWR (E6-5) - Body ground (*5) | GR - Body ground | Rear right door lock position switch input | Rear right door locked | 10 to 14 V |
| Rear right door unlocked | Below 1 V | |||
| RCTY (E6-7) - Body ground (*4) | GR - Body ground | Rear right door courtesy switch input | Rear right door open | Below 1 V |
| Rear right door closed | 10 to 14 V | |||
| HEAD (E6-17) - Body ground | P- Body ground | Light control switch HEAD input | Light control switch in HEAD | Below 1 V |
| Light control switch not in HEAD | 10 to 14 V | |||
| CLTS (E6-19) - Body ground | G- Body ground | Automatic light control sensor signal input | Ignition switch OFF | Below 1 V |
| Automatic light control system operates | Pulse generation (See waveform 1) | |||
| RFOG (E6-9) - Body ground (*3) | SB - Body ground | Fog light switch REAR input | Fog light switch in REAR | Below 1 V |
| Fog light switch OFF | 10 to 14 V | |||
| CLTB (E6-20) - Body ground | B - Body ground | Automatic light control sensor power supply output | Ignition switch OFF | Below 1 V |
| Ignition switch ON and light control switch in AUTO | 10 to 14 V | |||
| PCTY (E6-21) - Body ground | Y - Body ground (*1) L - Body ground (*2) | Passenger side door courtesy switch input | Passenger side door open | Below 1 V |
| Passenger side door closed | 10 to 14 V | |||
| LGCY (E6-25) - Body ground | W - Body ground | Luggage courtesy switch input | Luggage compartment door open | Below 1 V |
| Luggage compartment door closed | 10 to 14 V | |||
| LSWP (E6-27) - Body ground (*4) | GR - Body ground (*1) L- Body ground (*2) | Passenger side and rear door lock position switches input | Passenger side and rear LH and rear RH doors locked | 10 to 14 V |
| Passenger side or rear LH or rear RH door unlocked | Below 1 V | |||
| LSWP (E6-27) - Body ground (*5) | LG - Body ground (*1) L - Body ground (*2) | Passenger side door lock position switches input | Passenger side door locked | 10 to 14 V |
| Passenger side door unlocked | Below 1 V | |||
| FFOG (E6-28) - Body ground | V - Body ground | Fog light switch FRONT input | Fog light switch in FRONT | Below 1 V |
| Fog light switch OFF | 10 to 14 V | |||
| RCTY (E6-5) - Body ground (*1) | GR - Body ground | Rear right door courtesy switch input | Rear right door open | Below 1 V |
| Rear right door closed | 10 to 14 V | |||
| HF (E7-13) - Body ground | R - Body ground | Dimmer switch HIGH FLASH signal input | Dimmer switch in HIGH FLASH position | Below 1 V |
| Dimmer switch not in HIGH FLASH position | 10 to 14 V | |||
| A (E7-21) - Body ground | G - Body ground | Light control switch AUTO signal input | Light control switch in AUTO | Below 1 V |
| Light control switch not in AUTO | 10 to 14 V | |||
| TAIL (E7-23) - Body ground | B - Body ground | Light control switch TAIL signal input | Light control switch in TAIL or HEAD | Below 1 V |
| Light control switch in neither TAIL nor HEAD | 10 to 14 V | |||
| DCTY (E7-24) - Body ground | L - Body ground (*1) Y - Body ground (*2) | Driver side door courtesy switch input | Driver side door open | Below 1 V |
| Driver side door closed | 10 to 14 V | |||
| FFGO (E7-4) - Body ground | R - Body ground | Front fog light relay drive output | Light control switch in TAIL and fog light switch in FRONT | Below 1 V |
| Fog light switch OFF | 10 to 14 V | |||
| LSWD (E7-9) - Body ground | L - Body ground (*1) Y - Body ground (*2) | Driver side door lock position switch input | Driver side door locked | 10 to 14 V |
| Driver side door unlocked | Below 1 V | |||
| CANH (E8-5) - Body ground | B - Body ground | CAN communication line H | Ignition switch ON | Pulse generation |
| Ignition switch OFF | Below 1 V | |||
| CANL (E8-6) - Body ground | W - Body ground | CAN communication line L | Ignition switch ON | Pulse generation |
| Ignition switch OFF | Below 1 V |
![]() |
Waveform 1
| Item | Contents |
| Tool setting | 5 V/DIV., 5 ms./DIV. |
| CHECK HEADLIGHT BEAM LEVEL CONTROL ECU |
Disconnect the A20 ECU connector.

Measure the voltage and resistance between the specified terminals of the wire harness side connectors and body ground.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IG (A20-1) - Body ground | GR - Body ground | IG power supply | Ignition switch OFF | Below 1 V |
| Ignition switch ON | 10 to 14 V |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E1 (A20-9) - Body ground | W - Body ground | Ground | Always | Below 1 Ω |
Reconnect the A20 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| SGR (A20-21) - E1 (A20-9) | G - W | Rear height control sensor ground | Always | Below 1 Ω |
| RH- (A20-23) - E1 (A20-9) | V - W | Leveling motor RH ground | Always | Below 1 Ω |
| LH- (A20-24) - E1 (A20-9) | GR - W | Leveling motor LH ground | Always | Below 1 Ω |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| B2 (A20-3) - E1 (A20-9) | P - W | Low beam headlight signal input | Low beam headlights ON | Below 1.5 V |
| Low beam headlights OFF | Above 5 V | |||
| SPDL (A20-5) - E1 (A20-9) | W - W | Initialization signal input | Terminal LVL and terminal GND of DLC3 connected | Below 1 V |
| Terminal LVL and terminal GND of DLC3 not connected | Approx. 5 V | |||
| WNG (A20-6) - E1 (A20-9) | P - W | Warning indicator drive output | Warning indicator ON | 10 to 14 V |
| Warning indicator OFF | Below 1 V | |||
| RH+ (A20-10) - E1 (A20-9) | R - W | Leveling motor RH power supply | Ignition switch OFF | Below 1 V |
| Ignition switch ON | 10 to 16 V | |||
| LH+ (A20-11) - E1 (A20-9) | Y - W | Leveling motor LH power supply | Ignition switch OFF | Below 1 V |
| Ignition switch ON | 10 to 16 V | |||
| SBR (A20-12) - SGR (A20-21) | B - G | Rear height control sensor power supply | Ignition switch OFF | Below 1 V |
| Ignition switch ON | 4.75 to 5.25 V | |||
| SPDR (A20-16) - E1 (A20-9) | Y - W | Vehicle speed signal input | Vehicle is driven at approx. 20 km/h | Pulse generation (See waveform 1) |
| RHE (A20-17) - E1 (A20-9) | LG - W | Leveling motor RH operation signal input | With low beam headlights ON, vehicle height not changed | Below 1 V |
| With low beam headlights ON, change vehicle height and keep for more than 3 seconds. | 1.0 to 14.4 V | |||
| LHE (A20-18) - E1 (A20-9) | W - W | Leveling motor LH operation signal input | With low beam headlights ON, vehicle height not changed | Below 1 V |
| With low beam headlights ON, change vehicle height and keep for more than 3 seconds. | 1.0 to 14.4 V | |||
| SHRL (A20-19) - SGR (A20-21) | L - G | Rear height control sensor signal input | Ignition switch OFF | Below 1 V |
| Ignition switch ON | 0.5 to 4.5 V |
![]() |
Waveform 1
| Item | Contents |
| Tool setting | 2 V/DIV., 2 ms./DIV. |