DTC B2326 CAN MS Bus Line Communication Malfunction |
DTC B1207 Certification ECU Communication Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1207 | No communication from certification ECU |
|
| B2326 | Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus. |
|

| 1.CHECK CAN MS BUS WIRE |
Turn the ignition switch off.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value | Result |
| E74-27 (CANH) - E74-28 (CANL) | Ignition switch off | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or higher: Open circuit in a main bus line | |||
| E74-27 (CANH) - E74-17 (E) | Ignition switch off | 200 Ω or higher | Below 200 Ω: CANH ground short |
| E74-28 (CANL) - E74-17 (E) | Ignition switch off | Below 200 Ω: CANL ground short |
Disconnected the cable from the negative (-) battery terminal.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value | Result |
| E74-27 (CANH) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| E74-28 (CANL) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
| OK | A |
NG
| B |
NG
| C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK WIRE HARNESS (CERTIFICATION ECU POWER SOURCE CIRCUIT) |
![]() |
Disconnect the certification ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E74-17 (E) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E74-1 (+B) - Body ground | Always | 10 to 14 V |
| E74-18 (IG) - Body ground | Ignition switch ON | 10 to 14 V |
|
| ||||
| OK | |
| 3.REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU) |
Replace the instrument panel junction block (main body ECU).
| NEXT | |
| 4.RECONFIRM DTC OUTPUT |
Recheck the DTC.
| Result | Proceed to |
| B2326 not output | A |
| B2326 output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C) |
![]() |
Disconnect the certification ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E74-27 (CANH) - E74-28 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 6.CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C) |
Reconnect the certification ECU connector.
![]() |
Disconnect the main body ECU connector (E8).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E8-16 (CANP) - E8-15 (CANN) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 7.CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO . 3 J/C) |
Disconnect the certification ECU connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E74-27 (CANH) - E74-17 (E) | Ignition switch off | 200 Ω or higher |
| E74-28 (CANL) - E74-17 (E) | Ignition switch off | 200 Ω or higher |
| E74-27 (CANH) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E74-28 (CANL) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 8.CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (MAIN BODY ECU - CAN NO. 3 J/C) |
Disconnect the main body ECU connector (E8).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E74-27 (CANH) - E74-17 (E) | Ignition switch off | 200 Ω or higher |
| E74-28 (CANL) - E74-17 (E) | Ignition switch off | 200 Ω or higher |
| E74-27 (CANH) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E74-28 (CANL) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||