METER / GAUGE SYSTEM > Speed Signal Circuit |
| for 2AZ-FE |

| for 2GR-FE |

| 1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM) |
![]() |
Check the output waveform.
Remove the combination meter assembly with connector(s) still connected.
Connect the oscilloscope to the terminals F2-12 (+S) and body ground.
Turn the ignition switch to the ON position.
Turn the wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Driving at approx. 20 km/h (12 mph) |
|
| ||||
| OK | ||
| ||
| 2.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE) |
![]() |
Remove the F2 connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F2-12 (+S) - Body ground | Turn the ignition switch to the ON position | 4.5 to 14 V |
|
| ||||
| OK | |
| 3.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE) |
![]() |
Remove the A25 (*1)/A26 (*2) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-23 (SP1) (*1) - Body ground | Turn the ignition switch to the ON position | 10 to 14 V |
| A26-12 (SP1) (*2) - Body ground | Turn the ignition switch to the ON position | 10 to 14 V |
|
| ||||
| OK | |
| 4.INSPECT SKID CONTROL ECU (INPUT WAVEFORM) |
![]() |
Check the input waveform.
Reconnect the A25 (*1)/A26 (*2) connector.
Remove the combination meter assembly with connector(s) still connected.
Connect the oscilloscope to the terminals F2-14 (SI) and body ground.
Turn the ignition switch to the ON position.
Turn the wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Driving at approx. 20 km/h (12 mph) |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (COMBINATION METER - NO. 3 JUNCTION BLOCK) |
Disconnect the 3P to 3U No. 3 junction block connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F2-12 (+S) - 3P-3 | Always | Below 1 Ω |
| F2-12 (+S) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK) |
Inspect for a short in the circuit that connected the No. 3 junction block shown in the wiring diagram.
Disconnect the 3H to 3O and 3A to 3H No. 3 junction block connectors.

Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3B-10 - Body ground | Turn the ignition switch to the ON position | 4.5 to 14 V |
| 3J-9 - Body ground | Turn the ignition switch to the ON position | 4.5 to 14 V |
Reconnect the 3H to 3O No. 3 junction block connectors.

Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3T-9 - Body ground | Turn the ignition switch to the ON position | 4.5 to 14 V |
| Result | Proceed to |
| Voltage is not present in one circuit | A |
| Voltage is present in all the circuit. | B |
|
| ||||
| A | |
| 7.SYSTEM CHECK |
Select the circuit in which is not present voltage in step 6.
| Tester Connection | System that uses the circuit | Proceed to |
| 3T-9 - Body ground | Audio/visual System | A |
| 3J-9 - Body ground | Wiper and Washer System | B |
| 3B-10 - Body ground | SFI System | C |
| 3B-10 - Body ground | Lighting System | D |
| 3B-10 - Body ground | Automatic Transaxle System | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 8.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER CIRCUIT) |
![]() |
Disconnect the F8 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F8-5 (SPD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 9.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER REPLAY CIRCUIT) |
![]() |
Disconnect the E26 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E26-19 (SPD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (ECM CIRCUIT) |
![]() |
Disconnect the A24 (*1) or A55 (*2) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-8 (SPD) (*1) - Body ground | Always | 10 kΩ or higher |
| A55-8 (SPD) (*2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU CIRCUIT) |
![]() |
Disconnect the A20 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A20-16 (SPDR) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 12.CHECK HARNESS AND CONNECTOR (TCM CIRCUIT) |
![]() |
Disconnect the C56 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C56-3 (SPD1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 13.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU) |
![]() |
Disconnect the F2 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-23 (SP1) (*1) - F2-14 (SI) | Always | Below 1 Ω |
| A25-23 (SP1) (*1) - Body ground | Always | 10 kΩ or higher |
| A26-12 (SP1) (*2) - F2-14 (SI) | Always | Below 1 Ω |
| A26-12 (SP1) (*2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||