LIN COMMUNICATION SYSTEM > TERMINALS OF ECU |
| CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) |
Disconnect the ID and IF instrument panel junction block connectors.

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| ID-10 (BECU) - Body ground | BE - Body ground*1 O - Body ground*2 | Battery power supply | Always | 11 to 14 V |
| IF-10 (GND1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the ID and IF instrument panel junction block connectors.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IR-9 (LIN1) - IF-10 (GND1)*1 | P - W-B | LIN communication line | Ignition switch ON | Pulse generation |
| E8-10 (LIN2) - IF-10 (GND1) | P - W-B | LIN communication line | Ignition switch ON | Pulse generation |
| CHECK POWER WINDOW REGULATOR MOTOR (DRIVER SIDE) |
Disconnect the I5*3 or H10*4 motor connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I5-2 (B) - I5-1 (GND)*3 H10-2 (B) - H10-1 (E)*4 | GR - W-B*3 W - W-B*4 | Battery power supply | Always | 11 to 14 V |
| I5-1 (GND) - Body ground*3 H10-1 (E) - Body ground*4 | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the I5*3 or H10*4 motor connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I5-9 (LIN) - I5-1 (GND)*3 H10-9 (LIN) - H10-1 (E)*4 | P - W-B | LIN communication line | Ignition switch ON | Pulse generation |
| CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for FRONT PASSENGER SIDE) (for LHD) |
Disconnect the H12 power window regulator motor assembly (for front passenger side) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| H12-2 (B) - H12-1 (GND) | GR - W-B | Battery power supply | Always | 11 to 14 V |
| H12-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the H12 power window regulator motor assembly (for front passenger side) connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| H12-9 (LIN) - H12-1 (GND) | P - W-B | LIN communication line | Ignition switch ON | Pulse generation |
| CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR RH SIDE) (for LHD) |
Disconnect the J7 power window regulator motor assembly (for rear RH side) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| J7-2 (B) - J7-1 (GND) | R - W-B | Battery power supply | Always | 11 to 14 V |
| J7-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the J7 power window regulator motor assembly (for rear RH side) connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| J7-9 (LIN) - J7-1 (GND) | P - W-B | LIN communication line | Ignition switch ON | Pulse generation |
| CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR LH SIDE) (for LHD) |
Disconnect the K7 power window regulator motor assembly (for rear LH side) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| K7-2 (B) - K7-1 (GND) | R - W-B | Battery power supply | Always | 11 to 14 V |
| K7-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the K7 power window regulator motor assembly (for rear LH side) connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| K7-9 (LIN) - K7-1 (GND) | P - W-B | LIN communication line | Ignition switch ON | Pulse generation |
| CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for LHD) |
Disconnect the M2 power window regulator master switch assembly connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| M2-11 (B) - M2-12 (GND) | LG - W-B | Battery power supply | Always | 11 to 14 V |
| M2-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the M2 power window regulator master switch assembly connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| M2-17 (LIN1) - M2-12 (GND) | P - W-B | LIN communication line | Ignition switch ON | Pulse generation |
| CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (w/ Sliding Roof System) |
Disconnect the Q12 ECU connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| Q12-1 (B) - Q12-2 (E) | B - W-B | Battery power supply | Always | 11 to 14 V |
| Q12-2 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the Q12 ECU connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| Q12-4 (MPX1) - Q12-2 (E) | P - W-B | LIN communication line | Ignition switch ON | Pulse generation |
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System) |
Disconnect the E74 certification ECU (smart key ECU assembly) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E74-1 (+B) - E74-17 (E) | W - W-B | Battery power supply | Always | 11 to 14 V |
| E74-17 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E74 certification ECU (smart key ECU assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E74-18 (IG) - E74-17 (E) | LG - W-B | Engine switch power supply | Engine switch on (IG) | 11 to 14 V |
| E74-18 (IG) - E74-17 (E) | LG - W-B | Engine switch power supply | Engine switch off | Below 1 V |
| E74-10 (LIN) - E74-17 (E) | BE - W-B | LIN communication line | Engine switch on (IG) | Pulse generation |
| CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ Entry and Start System) |
Disconnect the E68 ID code box (immobiliser code ECU) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E68-1 (+B) - E68-8 (GND) | W - W-B | Battery power supply | Always | 11 to 14 V |
| E68-8 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E68 ID code box (immobiliser code ECU) connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E68-3 (LIN1) - E68-8 (GND) | BE - W-B | LIN communication line | Engine switch on (IG) | Pulse generation |
| CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (w/ Entry and Start System) |
Disconnect the E69 steering lock ECU (steering lock actuator assembly) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E69-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| E69-6 (IG2) - E69-1 (GND) | B - W-B | Engine switch power supply | Engine switch on (IG) | 11 to 14 V |
| E69-6 (IG2) - E69-1 (GND) | B - W-B | Engine switch power supply | Engine switch off | Below 1 V |
| E69-7 (B) - E69-1 (GND) | P - W-B | Battery power supply | Always | 11 to 14 V |
Reconnect the E69 steering lock ECU (steering lock actuator assembly) connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E69-5 (LIN) - E69-1 (GND) | BE - W-B | LIN communication line | Engine switch on (IG) | Pulse generation |