Home › COMMUNICATION SYSTEM › MULTIPLEX COMMUNICATION › LIN COMMUNICATION SYSTEM

DTC    B2321    Driver Side Door ECU Communication Stop

for Preparation Click here


DESCRIPTION

This DTC is output when LIN communication between the power window regulator motor (Driver side) and main body ECU (Instrument panel junction block) stops for more than 10 seconds.

DTC No.
DTC Detection Condition
Trouble Area
B2321
No communication between power window regulator motor (Driver side) and main body ECU (instrument panel junction block) for more than 10 seconds
  1. Power window regulator motor (Driver side)
  2. Main body ECU (Instrument panel junction block)
  3. Wire harness or connector

WIRING DIAGRAM


B176995E29


INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.

1.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2.CHECK DTC OUTPUT
  1. Recheck for DTC (Click here).

    Result:
    Result
    Proceed to
    B2321 is output
    A
    B2321 is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MOTOR)


  1. Disconnect the E8 and I5*1 or H10*2 connectors.

    HINT:
    *1: for LHD
    *2: for RHD


    B178903E10

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-10 (LIN2) - I5-9 (LIN)*1
    E8-10 (LIN2) - H10-9 (LIN)*2
    Always
    Below 1 Ω
    E8-10 (LIN2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    *1: for LHD
    *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-10 (LIN2) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND)


    B197874E08
  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    I5-1 (E) - Body ground*1
    H10-1 (E) - Body ground*2
    Always
    Below 1 Ω

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    I5-2 (B) - Body ground*1
    H10-2 (B) - Body ground*2
    Always
    11 to 14 V

    HINT:
    *1: for LHD
    *2: for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE POWER WINDOW REGULATOR MOTOR (DRIVER SIDE)
  1. Replace the power window regulator motor (Driver side) (Click here).


NEXT


6.CHECK DTC OUTPUT
  1. Clear the DTC (Click here).

  1. Recheck for DTC.

    Result:
    Result
    Proceed to
    B2321 is not output
    A
    B2321 is output
    B



B
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
A

END (POWER WINDOW REGULATOR MOTOR (DRIVER SIDE) IS DEFECTIVE)