Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM

TOYOTA PARKING ASSIST-SENSOR SYSTEM > Clearance Sonar Main Switch Circuit

for Preparation Click here


DESCRIPTION

When the clearance sonar main switch is turned on, an on signal is sent to the clearance warning ECU.
The Toyota parking assist-sensor system starts operating when the on signal is input to the clearance warning ECU S17-19 (CBZ) terminal (power source terminal).
If the clearance warning ECU S17-19 (CBZ) terminal is receiving the on signal but the S17-4 (+B) terminal (corner sensor detection range adjusting terminal) does not receive the signal, the Toyota parking assist-sensor system will operate but the detection range of the corner sensors will become narrower.
When the corner sensor detection range becomes narrower, the detection range will not change in the front (approximately 500 mm (19.69 in.)), but will change to approximately 500 mm (19.69 in.) or less around the corner sensors.
When the back sensor detection range switching connector is connected, the clearance warning ECU S17-22 (L8) terminal (back sensor detection range switching terminal) will receive an on signal. As a result, the short detection range will be 500 +/- 50 mm (19.69 +/- 1.97 in.).
When the back sensor detection range switching connector is disconnected, the clearance warning ECU S17-22 (L8) terminal (back sensor detection range switching terminal) will not receive an on signal. As a result, the short detection range for the back sensors will be 700 +/- 70 mm (27.56 +/- 2.76 in.).
In addition, when the back sensor detection range switching connector circuit has an open or short circuit, the clearance warning ECU S17-22 (L8) terminal (back sensor detection range switching terminal) will not receive an on signal. As a result, the short detection range for the back sensors will be 700 +/- 70 mm (27.56 +/- 2.76 in.).

WIRING DIAGRAM


E159936E01


INSPECTION PROCEDURE

NOTICE:
  1. When inspecting the vehicle side wire harness for the clearance sonar main switch and clearance warning ECU, proper inspection cannot be done if the back sensor detection range switching connector is disconnected.
  2. Be sure to inspect the vehicle side wire harness for the clearance sonar main switch and clearance warning ECU with the back sensor detection range switching connector connected.

1.INSPECT FUSE (ECU IG NO. 2)
  1. Remove the ECU IG NO. 2 fuse from the main body ECU (instrument panel junction block).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU IG NO. 2 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - CLEARANCE SONAR MAIN SWITCH)


    E159918E04
  1. Disconnect the S17 connector from the clearance warning ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S17-4 (+B) - S17-9 (E)
    Ignition switch ON, Clearance sonar main switch ON
    11 to 14 V
    S17-19 (CBZ) - S17-9 (E)
    Ignition switch ON, Clearance sonar main switch ON
    11 to 14 V
    S17-21 (L8) - S17-9 (E)
    Ignition switch ON, Clearance sonar main switch ON, Back sensor detection range switching connector connected
    11 to 14 V



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - CLEARANCE SONAR MAIN SWITCH)


    E159924E01
  1. Disconnect the S17 connector from the clearance warning ECU.

  1. Disconnect the E66 connector from the clearance sonar main switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S17-4 (+B) - E66-1
    Always
    Below 1 Ω
    S17-19 (CBZ) - E66-1
    Always
    Below 1 Ω
    S17-21 (L8) - E66-1
    Back sensor detection range switching connector connected
    Below 1 Ω
    S17-4 (+B) - Body ground
    Always
    10 kΩ or higher
    S17-9 (E) - Body ground
    Always
    Below 1 Ω
    S17-19 (CBZ) - Body ground
    Always
    10 kΩ or higher
    S17-21 (L8) - Body ground
    Back sensor detection range switching connector connected
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT CLEARANCE SONAR MAIN SWITCH


    E159911E01
  1. Remove the clearance sonar main switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E66-1 - E66-3
    Clearance sonar main switch OFF
    10 kΩ or higher
    E66-1 - E66-3
    Clearance sonar main switch ON
    Below 1 Ω



NG
REPLACE CLEARANCE SONAR MAIN SWITCH (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR