Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
NM19V0EQ _51 Engine / Hybrid System _014243 2AR-FE ENGINE CONTROL _0072842 SFI SYSTEM DE DETAILS F

2AR-FE ENGINE CONTROL  SFI SYSTEM  DETAILS  ACCELERATOR PEDAL SENSOR  


CONSTRUCTION


a.

This non-contact type accelerator pedal sensor assembly uses a Hall IC, which is mounted on the accelerator pedal arm.

i.

A magnetic yoke is mounted at the base of the accelerator pedal arm. This yoke rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur into electrical signals, and outputs them in the form of accelerator pedal sensor signals to the ECM.


ii.

The Hall IC contains 2 circuits, 1 for the main signal, and 1 for the sub signal. It converts the accelerator pedal position (angle) into electric signals that have differing characteristics and outputs them to the ECM.

W100142
1.146,2.906 1.469,2.906 1.469,2.906 2.031,2.104 true 1.583,3.438 1.781,3.438 1.781,3.438 2.302,2.365 true 2.063,0.406 1.833,0.406 1.833,0.406 1.167,1.938 true 3.396,1.167 3.656,1.167 3.656,1.167 4.49,1.594 true 3.396,2.448 3.635,2.448 3.635,2.448 4.531,2.031 true 4.167,2.969 4.333,2.969 4.333,2.969 4.542,2.469 true 4.188,0.573 4.375,0.573 4.375,0.573 4.594,1.125 true 3.344,3.354 5.625,3.552 2.281,0.198 10 Accelerator Pedal Sensor Assembly 2.354,6.313 4.521,6.51 2.167,0.198 10 Accelerator Pedal Position (Angle) 2.115,0.313 2.615,0.5 0.5,0.188 10 Hall IC 6.313,1.781 6.719,1.927 0.406,0.146 10 ECM 2.927,1.083 3.427,1.271 0.5,0.188 10 Hall IC 2.927,2.365 3.427,2.552 0.5,0.188 10 Hall IC 0.125,2.792 1.073,2.958 0.948,0.167 10 Magnetic Yoke 3.656,0.51 4.219,0.677 0.563,0.167 10 Magnet 3.656,2.875 4.24,3.104 0.583,0.229 10 Magnet 0.146,3.333 1.583,3.5 1.438,0.167 10 Accelerator Pedal Arm 5.406,1.021 5.771,1.198 0.365,0.177 10 VPA 3.802,5.375 4.167,5.552 0.365,0.177 10 VPA 5.417,1.385 5.781,1.563 0.365,0.177 10 EPA 5.417,1.708 5.854,1.885 0.438,0.177 10 VCPA 5.417,2.729 5.854,2.906 0.438,0.177 10 VCP2 5.417,1.99 5.854,2.167 0.438,0.177 10 VPA2 2.729,5.01 3.167,5.188 0.438,0.177 10 VPA2 5.406,2.365 5.844,2.542 0.438,0.177 10 EPA2 0.594,5.167 1.542,5.333 0.948,0.167 10 Output Voltage 0.792,6.24 1.604,6.417 0.813,0.177 10 Fully Closed 5.24,6.146 5.979,6.323 0.74,0.177 10 Fully Open 1.521,4.281 1.656,4.458 0.135,0.177 10 5 1.438,4.042 1.708,4.25 0.271,0.208 10 (V) 1.521,5.958 1.656,6.135 0.135,0.177 10 0

HINT:

The inspection method differs from a contact type sensor because this non-contact type sensor uses a Hall IC. For details, refer to the Repair Manual.