Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
NM19V0EQ _52 Drivetrain _014252 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0072852 AUTOMATIC TRANSAXLE SYSTEM CO CONTROL F

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  CONTROL  AUTOMATIC TRANSMISSION CONTROL  


SYSTEM CONTROL


a.

The electronic control system of the U760E automatic transaxle uses the controls listed below.

Control Outline
Shift Timing Control The ECM sends current to shift solenoid valves SL1, SL2, SL3, SL4, SL and/or SLU based on signals from various sensors, in order to shift the gears.
Clutch to Clutch Pressure Control Controls the pressure that is applied directly to the C1, C2 clutches and B1, B3 brakes by actuating the shift solenoid valves (SL1, SL2, SL3 and SL4) in accordance with ECM signals.
Line Pressure Control Actuates shift solenoid valve SLT to control the line pressure in accordance with information from the ECM and the operating conditions of the transaxle.
Lock-up Timing Control The ECM sends current to shift solenoid valves SL and SLU based on signals from various sensors to engage or disengage the lock-up clutch.
Flex Lock-up Clutch Control Controls shift solenoid valve SLU, provides an intermediate mode between the on and off states of the lock-up clutch, and increases the operating range of the lock-up clutch to improve fuel economy.
Powertrain Cooperative Control Controls both shift control and engine output control in an integrated way, achieving excellent shift characteristics and drivability.
Deceleration Downshift Control To prevent engine speed from decreasing and thereby maintain fuel cut, the ECM performs downshifts before fuel cut ends.
Direct Downshift Control Direct downshift control is used. This makes it possible to skip unnecessary shifts, enabling the vehicle to downshift directly from 6th to 3rd or from 5th to 2nd, enhancing downshift response when the accelerator pedal is depressed quickly.
Artificial Intelligence Shift Control (AI-shift Control) Based on the signals from various sensors, the ECM determines the road conditions and the intention of the driver. Thus, an appropriate shift pattern is automatically determined, improving drivability.
Multi-mode Automatic Transmission
·

The ECM appropriately controls the automatic transaxle in accordance with the range selected while the shift lever is in S.

·

Operating the shift paddle switch (transmission shift switch assembly) "-" (DOWN) with the shift lever in D enables temporary S mode. temporary S mode allows a fixed range mode identical to the S with the shift lever remaining in D.*


Shift Lock System The shift lock mechanism prevents the shift lever from being moved to any position other than P, unless the ignition switch is ON, and the brake pedal is depressed.
Fail-safe If a malfunction is detected in the sensors or solenoids, the ECM performs fail-safe control to prevent the vehicle drivability from being affected significantly.
Diagnosis When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information that relates to the fault.

*: Models with shift paddle switch



b.

Clutch to Clutch Pressure Control

i.

Clutch to clutch pressure control is used for shift control. As a result, shift control in 2nd gear or above is possible without using a one-way clutch, making the automatic transaxle lightweight and compact.


ii.

Based on the information about transmission input and output speed, engine torque and other items, the ECM controls each clutch and brake accordingly with the optimum fluid pressure and timing, in order to shift the gears. The ECM changes gears using fluid pressure circuits which enable the clutches and brakes (C1, C2, B1 and B3) to be controlled independently, and using high flow SL1, SL2, SL3 and SL4 shift solenoid valves which directly control the line pressure. As a result, highly responsive and excellent shift characteristics have been realized.

X105993
5.563,4.156 6.5,4.479 0.938,0.323 10 Line Pressure 3.844,0.469 6.521,0.833 2.677,0.365 10 Intake Mass Air Flow Meter Sub-assembly 3.844,1.063 6.635,1.385 2.792,0.323 10 E. F. I. Engine Coolant Temperature Sensor 3.854,1.635 5.417,1.948 1.563,0.313 10 Throttle Position Sensor 2.865,1.042 3.25,1.344 0.385,0.302 10 ECM 0.625,0.479 2.271,0.844 1.646,0.365 10 ATF Temperature Sensor 0.729,1.063 2.25,1.365 1.521,0.302 10 Input Speed Sensor NT 0.615,1.635 2.24,1.917 1.625,0.281 10 Output Speed Sensor NC



c.

Line Pressure Control

i.

The line pressure is controlled using shift solenoid valve SLT.


ii.

Through the use of shift solenoid valve SLT, the line pressure is appropriately controlled in accordance with the engine torque information, as well as with the internal operating conditions of the torque converter and the transaxle.


iii.

Accordingly, the line pressure can be accurately controlled in accordance with the engine output, traveling condition, and the ATF temperature, thus realizing smooth shift characteristics and regulating the workload of the oil pump (reducing unnecessary parasitic losses).

X105994
2.99,1.344 4.74,1.625 1.75,0.281 10 Solenoid Valve Drive Signal 5.479,1.75 6.969,2 1.49,0.25 10 Input Speed Sensor NT 5.49,2.156 6.646,2.427 1.156,0.271 10 ATF Temperature 5.49,2.583 6.406,2.896 0.917,0.313 10 Shift Position 5.49,2.99 6.396,3.313 0.906,0.323 10 Gear Position 5.479,3.792 6.865,4.313 1.385,0.521 10 Throttle Valve Opening Angle 5.49,3.396 6.51,3.75 1.021,0.354 10 Intake Air Mass 5.5,4.927 6.458,5.292 0.958,0.365 10 Engine Coolant Temperature 5.5,4.51 6.458,4.854 0.958,0.344 10 Engine Speed 0.219,0.031 1.438,0.323 1.219,0.292 10 Line Pressure 1.615,0.781 2.813,1.104 1.198,0.323 10 Primary Regulator 0.865,4.333 1.281,4.698 0.417,0.365 10 Pump 1.938,4.333 2.531,4.719 0.594,0.385 10 Fluid Pressure 2.875,5.063 3.417,5.396 0.542,0.333 10 Current 3.469,3.688 4.365,4.302 0.896,0.615 10 Shift Solenoid Valve SLT 4.875,3.125 5.24,3.406 0.365,0.281 10 ECM



d.

Lock-up Timing Control

i.

The ECM uses lock-up timing control in order to improve the fuel economy in 2nd gear or higher when the shift lever is in D, or when the S6, S5 or S4 range has been selected.

X100036
2.531,0.969 2.375,0.969 2.375,0.969 2.615,1.51 true 2.771,1.49 3.177,0.25 3.177,0.25 3.354,0.25 true 2.958,1.49 3.25,0.667 3.25,0.667 3.427,0.667 true 3.198,1.5 3.354,1.115 3.354,1.115 3.49,1.115 true 1.906,0.208 2.292,0.583 0.385,0.375 10 Large 2.583,0.875 2.833,1.25 0.25,0.375 10 2nd 3.406,0.167 3.635,0.5 0.229,0.333 10 3rd 3.479,0.583 3.698,0.958 0.219,0.375 10 4th 3.542,1.031 3.76,1.406 0.219,0.375 10 5th 4.469,1.375 4.698,1.75 0.229,0.375 10 6th 4.875,1.792 5.188,2.115 0.313,0.323 10 High 2.76,1.781 3.677,2.104 0.917,0.323 10 Vehicle Speed 2.656,2.198 5.365,2.573 2.708,0.375 10 Lock-up Operating Range in Each Gear 1.771,0.698 2.323,1.656 0.552,0.958 10 Throttle Opening Angle

Lock-up Operation:
Gear Shift Lever Position or Range
D or S6 S5 S4
1st X X X
2nd ○ ○ ○
3rd ○ ○ ○
4th ○ ○ ○
5th ○ ○ -
6th ○ - -

HINT:

○: Operates

X: Does not operate

-: Not applicable




e.

Flex Lock-up Clutch Control

i.

During acceleration, the partial control of the power transmission between the lock-up clutch and torque converter greatly boosts the transmission efficiency in accordance with the driving conditions, improving the fuel economy.


ii.

Even when the vehicle is decelerating (the accelerator pedal is released), flex lock-up clutch control operates. Therefore, the fuel-cut area of the engine has been expanded and fuel-economy has been improved.


iii.

By allowing flex lock-up clutch control to continue operating during gearshifts, smooth torque transmission has been obtained. As a result, fuel economy and drivability have been improved.


iv.

For flex lock-up control, H infinity (H∞) control theory is used to achieve a high level of system stability and response to various characteristic changes.

X110944
1.729,1.875 1.729,0.958 true 2.656,3.229 2.656,2.896 2.656,2.896 2.406,2.896 true 2.115,3.667 2.115,4.25 2.115,4.25 1.781,4.25 true 3.833,4.563 3.833,5.417 3.833,5.417 3.333,5.417 true 4.135,4.563 4.135,5.417 4.135,5.417 4.667,5.417 true 4.5,4.354 4.5,4.833 4.5,4.833 4.667,4.833 true 0.917,1.115 0.917,0.281 0.917,0.281 1.333,0.281 true 4.625,3.792 4.292,3.792 true 1.396,0.177 2.792,0.417 1.396,0.24 10 Engine Speed Signal 0.219,0.708 0.667,1.208 0.448,0.5 10 Engine Speed 0.802,1.406 1.823,1.771 1.021,0.365 10 Vehicle Speed 0.979,1.906 2.542,2.188 1.563,0.281 10 Speed Sensor NT Signal 0.885,2.781 2.427,2.99 1.542,0.208 10 Throttle Position Sensor 3.75,0.698 4.146,0.896 0.396,0.198 10 ECM 4.948,1.563 5.427,1.823 0.479,0.26 10 Current 5.938,2.26 6.458,2.521 0.521,0.26 10 Time 6.313,1.656 6.865,2.281 0.552,0.625 10 Linear Solenoid Signal 3.563,2.333 4.01,2.938 0.448,0.604 10 Engine Speed Signal 0.396,4.177 1.75,4.74 1.354,0.563 10 E.F.I. Engine Coolant Temperature Sensor 1.938,5.292 3.365,5.656 1.427,0.365 10 Lock-up Control Valve 4.75,5.313 6.313,5.542 1.563,0.229 10 Shift Solenoid Valve SLU 4.729,4.74 6.417,4.979 1.688,0.24 10 ATF Temperature Sensor 4.688,3.708 5.594,4.104 0.906,0.396 10 Speed Sensor NT


v.

The flex lock-up operating range has been expanded. Flex lock-up begins operating once the vehicle starts moving to lower engine speed and improve fuel economy.

X106854
2.521,0.896 2.333,0.896 2.333,0.896 2.729,2 true 4.24,0.208 3.99,0.208 3.99,0.208 4.542,1.573 true 1.594,0.667 1.979,1.042 0.385,0.375 10 Large 4.719,2.281 5.031,2.656 0.313,0.375 10 High 2,2.26 2.917,2.635 0.917,0.375 10 Vehicle Speed 2.979,2.427 4.531,3.104 1.552,0.677 10 Flex Lock-up Operating Range (Deceleration) 4.281,0.115 5.896,0.49 1.615,0.375 10 Lock-up Operating Range 2.594,0.823 4.094,1.5 1.5,0.677 10 Flex Lock-up Operating Range (Acceleration) 2.5,2.927 4.438,3.302 1.938,0.375 10 Flex Lock-up Operating Range 1.427,1.354 1.979,2.375 0.552,1.021 10 Throttle Opening Angle

Flex Lock-up Operation:
Gear Shift Lever Position or Range
D S6 S5 S4
1st ○ X X X
2nd ○ ○ ○ ○
3rd ○ ○ ○ ○
4th ○* ○* ○* ○*
5th ○* ○* ○* -
6th ○* ○* - -

HINT:

○: Operates

X: Does not operate

-: Not applicable

*: Flex lock-up clutch control also operates when the vehicle decelerates.




f.

Powertrain Cooperative Control

i.

The engine output is appropriately controlled with the Electronic Throttle Control System-intelligent (ETCS-i) in real-time according to the transient force from the torque converter when the vehicle is launched. This achieves a high response and smooth acceleration, ensuring excellent launch performance.

X106856
4.073,1.698 5.552,2.365 1.479,0.667 10 High Response and Smooth Acceleration 0.292,0.688 1.083,1.083 0.792,0.396 10 Accelerator Pedal Angle 0.156,1.385 1.104,2.094 0.948,0.708 10 Throttle Valve Opening Angle 0.333,3.125 1.094,3.5 0.76,0.375 10 Drive Force 5.01,3.406 5.385,3.708 0.375,0.302 10 Time 5.688,0.292 7.115,0.667 1.427,0.375 10 : Conventional A/T 5.688,0.677 6.615,1.052 0.927,0.375 10 : U760E


ii.

The ECM determines the gear that is to be selected when the accelerator pedal is released (released completely) in accordance with the way the accelerator pedal is released (quickly or slowly) during deceleration. In this way, unnecessary upshifts are prevented during deceleration, matching the driver's intentions. In addition, unintended downshifts are prevented when accelerating the vehicle again, achieving smooth acceleration.

X100034
1.427,1.958 1.427,1.719 1.427,1.719 1.531,1.719 false 1.927,1.833 1.927,1.563 1.927,1.563 2.063,1.563 false 2.417,1.729 2.417,1.396 2.417,1.396 2.542,1.396 false 2.802,1.594 2.802,1.229 2.802,1.229 2.938,1.229 false 0.021,0.604 1.365,0.938 1.344,0.333 10 Speed of Accelerator Pedal Operation 0.823,1.604 1.271,1.979 0.448,0.375 10 Gear 0.542,2.24 1.427,2.615 0.885,0.375 10 Drive Force 1.583,1.604 1.854,1.938 0.271,0.333 10 3rd 2.094,1.469 2.365,1.802 0.271,0.333 10 4th 2.563,1.302 2.833,1.635 0.271,0.333 10 5th 2.99,1.146 3.26,1.479 0.271,0.333 10 6th 4.531,0.125 6.906,0.5 2.375,0.375 10 : Accelerator Pedal Operation (Slow) 4.531,0.479 6.906,0.854 2.375,0.375 10 : Accelerator Pedal Operation (Quick) 5.26,3.323 5.615,3.698 0.354,0.375 10 Time 4.177,1.979 5.729,2.635 1.552,0.656 10 Drive force change according to driver input.


iii.

Through cooperative control with the Electronic Throttle Control System-intelligent (ETCS-i) and Electronic Spark Advance (ESA), and electronic control of the engagement and release speed of the clutch and brake hydraulic pressures, quick response and shift shock reduction have been achieved.

X105996
0.896,0.49 2.167,1 1.271,0.51 10 Driver's desired drive force 3.833,1.573 4.219,1.781 0.385,0.208 10 ECM 0.219,2.042 1.406,2.594 1.188,0.552 10 Accelerator Pedal Operation 1.615,2.167 2.583,2.521 0.969,0.354 10 ETCS-i Control 1.76,2.813 2.594,3.167 0.833,0.354 10 ESA Control 0.979,4.552 1.896,4.906 0.917,0.354 10 Engine output 4.469,4.5 5.75,5.156 1.281,0.656 10 Driver's desired drive force is achieved 5.365,2.167 6.677,2.76 1.313,0.594 10 Shift Solenoid Valve (SL1, SL2, SL3, SL4) 3.01,2.448 4.823,3.052 1.813,0.604 10 Clutch engagement hydraulic pressure and timing



g.

Coast Downshift Control

i.

The ECM performs downshift control to help prevent the engine speed from decreasing, thus keeping fuel cut control operating for as long as possible. In this way, fuel economy is improved.


ii.

For this control, when the vehicle is in 6th gear and starts decelerating, the transaxle downshifts from 6th to 5th, 5th to 4th, and 4th to 3rd before fuel cut control ends so that fuel cut continues operating.

X104227
3.073,3.448 3.073,3.604 3.073,3.604 2.885,3.604 true 3.344,3.448 3.344,3.677 true 2.469,3.073 2.469,2.635 2.469,2.635 2.396,2.635 true 2.75,3.229 2.75,2.313 2.75,2.313 2.656,2.313 true 3.208,1.198 3.031,0.646 3.031,0.646 2.802,0.646 true 3.073,3.271 3.073,2.313 3.073,2.313 3.292,2.313 true 3.396,3.302 3.396,2.563 3.396,2.563 3.979,2.563 true 3.604,3.448 3.604,3.677 true 4.698,0.677 6.26,0.896 1.563,0.219 10 : With Downshift Control 4.688,1.042 6.448,1.26 1.76,0.219 10 : Without Downshift Control 1.51,0.563 2.844,0.958 1.333,0.396 10 Continuous Fuel Cut Operation 0.792,1.354 2.125,1.667 1.333,0.313 10 Fuel Cut Control On 0.781,1.802 2.115,2.135 1.333,0.333 10 Fuel Cut Control Off 2.24,2.24 2.719,2.458 0.479,0.219 10 To 5th 2.167,2.552 2.479,2.771 0.313,0.219 10 6th 3.083,3.719 3.563,3.938 0.479,0.219 10 To 4th 2.458,3.521 2.938,3.74 0.479,0.219 10 To 5th 3.333,2.24 3.813,2.458 0.479,0.219 10 To 4th 4.042,2.49 4.521,2.708 0.479,0.219 10 To 3rd 1.146,2.688 2.125,2.906 0.979,0.219 10 Engine Speed 4.927,2.708 5.802,2.927 0.875,0.219 10 Fuel Cut On 4.927,3.604 5.802,3.823 0.875,0.219 10 Fuel Cut Off 4.708,4.063 5.135,4.281 0.427,0.219 10 Time 3.563,3.708 4.042,3.927 0.479,0.219 10 To 3rd



h.

Direct Downshift Control

i.

For conventional downshift control, when shifting from 6th to 3rd or 5th to 2nd, downshifts use an intermediate gear in order to achieve smooth acceleration response. In addition to conventional control, direct downshift control is used for this vehicle. This control skips unnecessary shifts, enabling the vehicle to downshift directly from 6th to 3rd or from 5th to 2nd.


ii.

When the accelerator pedal is depressed quickly, direct downshift control enables direct downshifts with a quick shift response, skipping unnecessary shifts. Direct downshift control places the emphasis on reducing the time required to achieve the target gear. Conventional downshift control is used when the accelerator pedal is depressed slowly, providing smooth acceleration response. As a result, this logic achieves downshift responsiveness in accordance with the driver's intentions.

X104223
3.865,1.188 4.26,0.385 4.26,0.385 4.583,0.385 true 2.938,0.427 3.063,0.427 3.063,0.427 3.365,0.927 true 4.271,2.927 4.5,2.521 4.5,2.521 5.281,2.521 true 4.26,4.167 4.448,3.823 4.448,3.823 5.229,3.823 true 4.427,4.427 4.427,5.188 4.427,5.188 4.771,5.188 true 1.417,0.323 3,0.708 1.583,0.385 10 Direct Downshift Control 4.688,0.281 6.688,0.448 2,0.167 10 Conventional Downshift Control 5.354,2.427 6.854,2.771 1.5,0.344 10 Conventional Downshift Control 4.844,5.104 6.813,5.458 1.969,0.354 10 Conventional Downshift Control 5.208,0.844 5.479,1.021 0.271,0.177 10 2nd 5.208,1.094 5.479,1.271 0.271,0.177 10 3rd 5.219,1.344 5.49,1.542 0.271,0.198 10 4th 5.208,1.594 5.479,1.854 0.271,0.26 10 5th 2.427,3.333 3.51,3.667 1.083,0.333 10 Direct Downshift Control 5.302,3.729 6.854,3.875 1.552,0.146 10 Direct Downshift Control 0.667,1.125 1.99,1.49 1.323,0.365 10 Automatic Transaxle Input Speed 0.833,2.125 2.031,2.813 1.198,0.688 10 Accelerator Pedal Operation 0.885,2.927 1.885,3.302 1,0.375 10 Response Time 1.219,4.656 1.958,5.083 0.74,0.427 10 Drive Force



i.

Artificial Intelligence Shift Control (AI-shift Control)

i.

The automatic transmission gear is determined by the shift pattern, which uses the vehicle speed and throttle valve opening angle.


ii.

Additionally, AI-shift control enables the ECM to estimate the road conditions and the driver's intention in order to automatically control the shift pattern in the manner. As a result, a comfortable ride has been achieved.


iii.

AI-shift control includes road condition support control and driver's intention support control.


iv.

AI-shift control determines transaxle control based on input signals and automatically changes the shift pattern.

X100041
0.573,0.229 1.396,0.427 0.823,0.198 10 Input Signals 0.542,0.865 1.458,1.063 0.917,0.198 10 Sensor Signal 0.375,1.208 1.563,1.573 1.188,0.365 10 - Throttle Opening Angle 0.375,1.865 1.375,2.042 1,0.177 10 - Vehicle Speed 0.375,2.25 1.375,2.406 1,0.156 10 - Engine Speed 0.375,2.646 1.375,2.823 1,0.177 10 - Brake Signal 0.396,3.698 1.625,3.865 1.229,0.167 10 Calculated by ECM 0.354,4.042 1.656,4.208 1.302,0.167 10 Vehicle Acceleration 2.302,0.688 3.26,0.885 0.958,0.198 10 AI-shift Control 2.563,1.042 3.583,1.24 1.021,0.198 10 Road Condition 2.74,1.406 4.188,1.563 1.448,0.156 10 Uphill/Downhill Driving 3.042,1.792 4.417,1.979 1.375,0.188 10 Estimating the Grade 2.333,2.042 2.719,2.229 0.385,0.188 10 Small 3.563,2.354 3.948,2.542 0.385,0.188 10 Large 2.771,2.688 4.219,2.854 1.448,0.167 10 Intended Acceleration 2.771,3.042 4.135,3.208 1.365,0.167 10 Actual Acceleration 2.573,3.792 3.667,3.979 1.094,0.188 10 Driver's Intention 2.354,4.208 3.365,4.583 1.01,0.375 10 - Accelerator Pedal Operation 2.354,4.76 3.542,4.938 1.188,0.177 10 - Vehicle Condition 3.875,4.208 4.917,4.604 1.042,0.396 10 Estimating the Driver's Intention 5.813,0.302 6.979,0.635 1.167,0.333 10 Basic Shift Pattern Control 5.813,2.313 6.854,2.635 1.042,0.323 10 Road Condition Support Control 5.813,4.563 6.906,4.885 1.094,0.323 10 Driver's Intention Support Control


v.

Under road condition support control, the ECM determines the throttle opening angle and the vehicle speed in addition whether the vehicle is being driven uphill or downhill. To achieve the drive force while driving uphill, this control prevents unnecessary upshifts. To achieve engine braking while driving downhill, this control automatically performs downshifts.

X100042
4.167,3.125 4.167,2.635 4.167,2.635 4.042,2.635 false 0.75,3.156 1.135,3.344 0.385,0.188 10 6th 0.75,3.656 1.167,3.865 0.417,0.208 10 6th 1.427,3.156 1.74,3.323 0.313,0.167 10 4th 1.625,3.656 2.01,3.885 0.385,0.229 10 4th 1.854,3.156 2.177,3.323 0.323,0.167 10 5th 2.531,3.156 2.865,3.375 0.333,0.219 10 5th 2.167,3.156 2.51,3.385 0.344,0.229 10 3rd 2.167,3.656 2.469,3.844 0.302,0.188 10 3rd 2.906,3.156 3.219,3.396 0.313,0.24 10 4th 4.365,3.656 4.792,3.865 0.427,0.208 10 3rd 3.281,3.656 3.646,3.854 0.365,0.198 10 4th 4.823,3.656 5.208,3.865 0.385,0.208 10 4th 5.302,3.656 5.573,3.833 0.271,0.177 10 5th 5.583,3.656 5.917,3.865 0.333,0.208 10 6th 5.583,3.135 5.969,3.427 0.385,0.292 10 6th 5.969,3.125 6.969,3.302 1,0.177 10 Without Control 5.99,3.635 6.802,3.813 0.813,0.177 10 With Control 3.333,2.552 4.031,2.917 0.698,0.365 10 5th (Brake Operating)


vi.

The ECM estimates the driver's intention based on the accelerator operation and vehicle operating conditions to select a shift pattern that is well-suited to each driver, without the need to operate the shift pattern select switch used in the conventional models.



j.

Multi-mode Automatic Transmission

i.

Multi-mode Automatic Transmission is designed to allow the driver to switch between gear ranges. By moving the shift lever to S and then moving the shift lever toward "+" (forwards) or to "-" (backwards), the driver can select the desired shift range. Thus, the driver is able to shift gears with a manual-like feel.


ii.

This Multi-mode Automatic Transmission is designed to allow the driver to switch gear ranges; it is not for manually selecting single gears.


iii.

When the vehicle is being driven at a speed that is higher than the maximum safe speed for a downshift, any attempt to shift to a lower range by operating the shift lever will not be performed. This is done in order to protect the automatic transaxle. In this case, the ECM sounds the buzzer in the combination meter assembly twice to alert the driver.

X105997
0.635,3.51 1.698,4.063 1.063,0.552 10 Ignition Advance Signal 1.938,3.938 2.844,4.438 0.906,0.5 10 Fluid Pressure Control Signal 3.229,4.448 4.531,5.031 1.302,0.583 10 Shift Solenoid Valve Control Signal 1.365,5.229 1.875,5.542 0.51,0.313 10 Engine 2.969,5.594 3.625,6.063 0.656,0.469 10 Automatic Transaxle 3.583,3.219 5.063,3.542 1.479,0.323 10 S Mode Position Signal 3.594,2.865 4.719,3.208 1.125,0.344 10 Shift-down Signal 3.594,2.521 4.719,2.865 1.125,0.344 10 Shift-up Signal 5.177,2.396 6.542,2.99 1.365,0.594 10 Transmission Control Switch 5.177,0.938 6.417,1.667 1.24,0.729 10 Shift Paddle Switch (Transmission Shift Switch Assembly)* 2.146,2.406 2.688,2.615 0.542,0.208 10 ECM 0.646,1.656 2.083,1.917 1.438,0.26 10 CAN (V Bus) 1.094,0.396 3.021,0.688 1.927,0.292 10 Combination Meter Assembly 1.177,0.781 2.427,1.104 1.25,0.323 10 Shift Indicator Light 1.177,1.188 2.646,1.531 1.469,0.344 10 S Mode Indicator Light 4.365,6.094 6.615,6.406 2.25,0.313 10 *: Models with Shift Paddle Switch


iv.

On models with the shift paddle switch, in addition to the shift lever, a shift paddle switch (transmission shift switch assembly) has been provided on the steering wheel, allowing shifting operation similar to that of a manual transmission.


v.

The driver can select S mode by moving the shift lever to S. At this time, the 4th or 5th shift range will be selected according to the vehicle speed (during AI-shift control, however, the 3rd shift range may be selected).


vi.

Under this control, the ECM performs shift control within the usable gear range that the driver selects. As with an ordinary automatic transaxle, it shifts to 1st gear when the vehicle is stopped.


vii.

The shift lever position and the shift range are indicated by the shift indicator light in the combination meter assembly (the shift range is shown only when the shift lever is in S, and it is not shown when the shift lever is in P, R, N or D).


viii.

When the shift lever is in S, the S mode indicator light in the combination meter assembly illuminates. The shift indicator light indicates the shift range that the driver has selected.


ix.

Holding the shift lever toward "+" with the shift lever in S will change the shift range to the S6 range regardless of the current range (S1 to S5).


x.

In order to prevent excessive engine speed, a function is used that automatically selects a higher shift range before engine speed becomes excessive.


xi.

In order to protect the automatic transmission, a function is adopted that automatically selects a higher shift range when the fluid temperature is high.

X106207
1.692,1.11 1.887,1.272 0.196,0.162 10 *a 4.906,2.896 5.101,3.059 0.196,0.162 10 *b
*a Transition of Shift Ranges *b Shift Pattern
V100145

Default Shift Range - -


Usable Gear Chart
Shift Range Shift Indicator Light Usable Gear
S6 6 1st to 6th
S5 5 1st to 5th
S4 4 1st to 4th
S3 3 1st to 3rd
S2 2 1st to 2nd
S1 1 1st



k.

Shift Lock System

i.

The shift lock system is controlled by the shift lock control ECU.


ii.

The shift lock mechanism prevents the shift lever from being moved to any position other than P, unless the ignition switch is ON, and the brake pedal is depressed. This mechanism helps to prevent unintentional acceleration.


iii.

The shift lock system mainly consists of the shift lock control ECU, shift lock solenoid assembly and shift lock release button.

X107105
0.656,2.26 2.25,3.031 1.594,0.771 10 false Certification ECU (Smart Key ECU Assembly)*2 5.438,0.781 6.479,1.427 1.042,0.646 10 false Shift Lock Solenoid 5.438,2.156 6.292,2.802 0.854,0.646 10 false P Detection Switch 0.865,0.438 2.063,1.188 1.198,0.75 10 false Stop Light Switch Assembly 2.99,1.156 4.229,1.906 1.24,0.75 10 false Shift Lock Control ECU 4.729,3.063 6.625,3.396 1.896,0.333 10 false Shift Lock Solenoid Assembly 3.99,3.604 5.875,3.938 1.885,0.333 10 false Lower Shift Lever Assembly 1.042,1.354 1.865,1.698 0.823,0.344 10 false IG2 Relay*1 0.333,3.938 3.417,4.271 3.083,0.333 10 false *1: Models without Smart Entry and Start System 0.333,4.26 3.219,4.594 2.885,0.333 10 false *2: Models with Smart Entry and Start System


iv.

The shift lock control ECU uses the P detection switch to detect the shift lever position, and receives inputs from the stop light switch assembly and the certification ECU (smart key ECU assembly) or IG2 relay. Upon receiving these signals, the shift lock control ECU turns on the shift lock solenoid in order to release the shift lock.




FUNCTION


a.

Shift Paddle Switch (Transmission Shift Switch Assembly)(Models with Shift Paddle Switch)

i.

When the shift lever is in S, the shift ranges can be selected by using the shift paddle switch (transmission shift switch assembly) located behind the steering wheel. Then, if the driver pulls the right shift switch (+) or the left one (-), the selected shift range changes one at a time.


ii.

Temporary S mode can be selected while driving with the shift lever in D by operating the "+" or "-" switches of the shift paddle switch (transmission shift switch assembly). When temporary S mode is selected, both the D indicator and the currently selected shift range are displayed in the combination meter assembly. When the "-" switch of the shift paddle switch (transmission shift switch assembly) is operated while the shift lever is in D, temporary S mode selects a shift range that is the same as the currently selected gear or the next lower gear.


iii.

The temporarily selected S mode is canceled when any of the following conditions are met.

Condition Control
When the vehicle is stopped. Returns to D mode.
When the accelerator pedal has been depressed for a specified amount of time.
When + of the shift paddle switch (transmission shift switch assembly) is operated for one second or more while the vehicle is being driven.
When the shift lever is moved to S. Changes from temporary S mode to S mode




FAIL-SAFE


a.

This fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or shift solenoid valve. For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information related to the fault. Furthermore, the ECM illuminates or blinks the Malfunction Indicator Lamp (MIL) in the combination meter assembly to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs stored in the ECM are output to an intelligent tester via the ECM and the DLC3. For details, refer to the Repair Manual.

HINT:

To clear a DTC that is stored in the ECM, use an intelligent tester, disconnect the cable from the battery terminal for 1 minute or longer.