Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › 2011.10–2015.04
NM19V0EQ _54 Brake _014260 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0072860 BRAKE CONTROL SYSTEM DE DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  DETAILS  BRAKE CONTROL  


OPERATION


a.

ABS with EBD

i.

Based on the signals received from the 4 speed sensors and airbag sensor assembly, the skid control ECU calculates each wheel speed and deceleration, and checks wheel slipping conditions. According to the slipping condition, the skid control ECU controls the pressure holding solenoid valve and pressure reduction solenoid valve in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes.

Hydraulic Circuit
X111456E02
0.833,0.583 1,0.583 1,0.583 1.24,1.156 true 0.833,1.917 1,1.917 1,1.917 1.24,2.406 true 0.396,0.49 0.927,0.708 0.531,0.219 10 Port A 0.26,0.865 0.833,1.563 0.573,0.698 10 Pressure Holding Solenoid Valve 0.25,2.313 0.823,3.01 0.573,0.698 10 Pressure Reduction Solenoid Valve 4.583,1.948 5.24,2.479 0.656,0.531 10 To Reservoir and Pump 5.135,3.115 6.625,3.396 1.49,0.281 10 From Wheel Cylinder 0.75,3.115 1.99,3.313 1.24,0.198 10 To Wheel Cylinder 0.375,1.813 0.906,2.031 0.531,0.219 10 Port B

Not Activated Normal Braking - -
Activated Increase Mode Holding Mode Reduction Mode
Pressure Holding Valve (Port A) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Valve (Port B) OFF (Closed) OFF (Closed) ON (Open)
Brake Wheel Cylinder Pressure Increased Held Reduced



b.

Brake Assist (Models with Brake Control System (ABS with EBD, Brake Assist, TRC and VSC))

i.

In the event of emergency braking, the skid control ECU determines the driver's intentions based on the speed of the pressure increase in the master cylinder detected by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure to supplement the amount provided by the master cylinder is generated by the pump in the brake actuator and directed to each wheel cylinder.


ii.

The skid control ECU also provides brake assist in the event of a brake booster failure. The skid control ECU judges a brake booster failure using the brake load sensing switch and master cylinder pressure sensor signals.

X105895E03
0.656,1.135 1.885,1.448 1.229,0.313 10 Speed Sensor (4) 0.417,2.271 2.073,2.729 1.656,0.458 10 Brake Pedal Load Sensing Switch 0.385,3.708 2.167,4.073 1.781,0.365 10 Stop Light Switch Assembly 3.146,0.677 4.115,1.021 0.969,0.344 10 Solenoid Relay 3.083,2.198 4.26,2.771 1.177,0.573 10 Skid Control ECU 3.208,3.719 4.063,4.063 0.854,0.344 10 Motor Relay 5.219,0.438 6.469,0.885 1.25,0.448 10 Master Cylinder Cut Solenoid Valve (2) 5.167,1.24 6.573,1.74 1.406,0.5 10 Reservoir Cut Solenoid Valve (2) 5.115,2.031 6.74,2.5 1.625,0.469 10 Pressure Holding Solenoid Valve (4) 5.031,2.844 6.823,3.365 1.792,0.521 10 Pressure Reduction Solenoid Valve (4) 5.5,3.635 6.396,3.927 0.896,0.292 10 Pump Motor 5.125,4.125 6.698,4.656 1.573,0.531 10 Master Cylinder Pressure Sensor 2.74,5.313 4.594,5.615 1.854,0.302 10 Combination Meter Assembly 5.438,4.979 7.042,5.26 1.604,0.281 10 Brake Actuator Assembly 2.99,6.188 4.25,6.531 1.26,0.344 10 ABS Warning Light 3.74,4.969 4.625,5.219 0.885,0.25 10 CAN (V Bus) 2.958,5.802 4.344,6.125 1.385,0.323 10 Brake Warning Light

Brake Assist Operation
X105896C02
2.948,0.719 3.615,0.719 true 4.771,1.854 5.438,1.854 true 3.302,5.167 3.448,5.333 3.448,5.333 3.448,5.979 true 3.938,5.167 3.802,5.333 3.802,5.333 3.802,5.979 true 3.385,6.917 3.385,6.552 true 3.865,6.917 3.865,6.552 true 0.656,2.698 1.323,2.698 true 0.677,4.177 1.604,4.177 true 2.146,2.698 2.656,2.698 true 4.604,2.688 5.115,2.688 true 5.917,2.688 6.604,2.688 true 5.656,4.177 6.615,4.177 true 2.052,4.521 2.052,4.177 2.052,4.177 2.521,4.177 true 5.188,4.51 5.188,4.177 5.188,4.177 4.74,4.177 true 0.656,5.365 1.604,5.365 true 2.167,6.344 2.167,5.375 2.167,5.375 2.542,5.375 true 5.656,5.365 6.615,5.365 true 5.104,6.344 5.104,5.375 5.104,5.375 4.74,5.375 true 2.781,0.635 3.042,0.906 0.26,0.271 10 *1 0.667,1.458 0.927,1.729 0.26,0.271 10 *2 4.615,1.781 4.875,2.052 0.26,0.271 10 *3 1.531,5.979 1.792,6.208 0.26,0.229 10 (9) 2.406,5.99 2.708,6.219 0.302,0.229 10 (10) 1.26,3.313 1.521,3.542 0.26,0.229 10 (1) 0.438,2.625 0.698,2.854 0.26,0.229 10 (A) 5.865,3.313 6.125,3.542 0.26,0.229 10 (4) 2.594,3.313 2.854,3.542 0.26,0.229 10 (2) 4.531,3.323 4.792,3.552 0.26,0.229 10 (3) 1.521,7.198 1.781,7.427 0.26,0.229 10 *6 2.469,7.198 2.729,7.427 0.26,0.229 10 *7 4.667,7.208 4.927,7.438 0.26,0.229 10 *8 5.625,7.188 5.885,7.417 0.26,0.229 10 *9 4.615,5.99 4.917,6.219 0.302,0.229 10 (11) 5.531,6.01 5.854,6.24 0.323,0.229 10 (12) 2.458,4.813 2.719,5.042 0.26,0.229 10 (6) 1.531,4.813 1.792,5.042 0.26,0.229 10 (5) 4.667,4.813 4.927,5.042 0.26,0.229 10 (7) 5.573,4.813 5.833,5.042 0.26,0.229 10 (8) 3.313,6.938 3.573,7.208 0.26,0.271 10 *5 3.729,6.01 3.99,6.281 0.26,0.271 10 *4 3.375,6.01 3.635,6.281 0.26,0.271 10 *4 3.802,6.948 4.063,7.219 0.26,0.271 10 *5 0.469,4.094 0.729,4.323 0.26,0.229 10 (E) 1.979,4.531 2.24,4.76 0.26,0.229 10 (F) 1.938,2.635 2.198,2.865 0.26,0.229 10 (B) 6.635,2.625 6.896,2.854 0.26,0.229 10 (D) 5.167,2.615 5.427,2.844 0.26,0.229 10 (C) 6.646,4.104 6.906,4.333 0.26,0.229 10 (H) 5.104,4.542 5.365,4.771 0.26,0.229 10 (G) 0.469,5.302 0.729,5.531 0.26,0.229 10 (I) 2.083,6.375 2.344,6.604 0.26,0.229 10 (J) 6.646,5.302 6.906,5.531 0.26,0.229 10 (L) 5.021,6.375 5.281,6.604 0.26,0.229 10 (K)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Left Side)
*7 Rear Brake Caliper (Right Side) *8 Rear Brake Caliper (Left Side)
*9 Front Brake Caliper (Right Side) - -



iii.

Each valve operates as shown below:

Item Port Brake Assist Not Activated Brake Assist Activated
Master Cylinder Cut Solenoid Valves (1), (4) (A), (D) OFF (Open) ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open)
Front Brakes Pressure Holding Solenoid Valves (5), (8) (E), (H) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valves (9), (12) (I), (L), OFF (Closed) OFF (Closed)
Rear Brakes Pressure Holding Solenoid Valves (6), (7) (F), (G) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valves (10), (11) (J), (K) OFF (Closed) OFF (Closed)
Pump OFF ON

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.



c.

TRC

i.

The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to achieve the required pressure. Thus, the brakes for the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes, to control slippage of the drive wheels.


ii.

The diagram shows the hydraulic circuit in pressure increase mode when TRC is activated. The pressure holding solenoid valve and the pressure reduction solenoid valve are turned ON/OFF according to the ABS and EBD operation pattern.

X106791
0.625,2.333 1.854,2.646 1.229,0.313 10 false Speed Sensor (4) 0.281,5.177 1.917,5.521 1.635,0.344 10 false Airbag Sensor Assembly 0.469,6.854 2.146,7.5 1.677,0.646 10 false Throttle Body with Motor Assembly 3.125,0.479 4.094,0.823 0.969,0.344 10 false Solenoid Relay 3.083,2.385 4.26,2.958 1.177,0.573 10 false Skid Control ECU 3.208,3.563 4.063,3.906 0.854,0.344 10 false Motor Relay 5.271,0.344 6.656,0.813 1.385,0.469 10 false Master Cylinder Cut Solenoid Valve (2) 5.188,1.146 6.719,1.708 1.531,0.563 10 false Reservoir Cut Solenoid Valve (2) 5.063,1.948 6.844,2.438 1.781,0.49 10 false Pressure Holding Solenoid Valve (4) 5.021,2.76 6.896,3.271 1.875,0.51 10 false Pressure Reduction Solenoid Valve (4) 5.49,3.563 6.385,3.854 0.896,0.292 10 false Pump Motor 5.146,4.063 6.75,4.594 1.604,0.531 10 false Master Cylinder Pressure Sensor 5.021,5.5 6.875,5.802 1.854,0.302 10 false Combination Meter Assembly 5.396,4.896 7,5.177 1.604,0.281 10 false Brake Actuator Assembly 5.281,6.01 6.667,6.333 1.385,0.323 10 false Brake Warning Light 5.354,6.396 6.615,6.74 1.26,0.344 10 false ABS Warning Light 5.344,6.813 6.656,7.115 1.313,0.302 10 false Slip Indicator Light 3.438,7.708 3.875,8.031 0.438,0.323 10 false ECM 3.75,5.875 4.604,6.25 0.854,0.375 10 false CAN (V Bus) 0.781,7.667 1.74,8 0.958,0.333 10 false Throttle Motor 0.49,8.063 2.094,8.396 1.604,0.333 10 false Throttle Position Sensor 0.271,5.552 1.906,5.896 1.635,0.344 10 false - Yawrate Sensor 0.25,5.885 1.885,6.229 1.635,0.344 10 false - Acceleration Sensor

TRC Operation
X105898C02
2.958,0.719 3.625,0.719 true 4.854,1.854 5.521,1.854 true 3.302,5.24 3.448,5.406 3.448,5.406 3.448,6.052 true 3.938,5.24 3.802,5.406 3.802,5.406 3.802,6.052 true 3.385,6.927 3.385,6.563 true 3.865,6.917 3.865,6.552 true 0.677,2.708 1.344,2.708 true 0.677,4.167 1.604,4.167 true 2.135,2.698 2.646,2.698 true 4.604,2.698 5.115,2.698 true 5.927,2.698 6.615,2.698 true 5.656,4.188 6.615,4.188 true 2.052,4.521 2.052,4.177 2.052,4.177 2.521,4.177 true 5.188,4.51 5.188,4.177 5.188,4.177 4.74,4.177 true 0.656,5.365 1.604,5.365 true 2.167,6.333 2.167,5.365 2.167,5.365 2.542,5.365 true 5.656,5.365 6.615,5.365 true 5.104,6.354 5.104,5.385 5.104,5.385 4.74,5.385 true 2.802,0.635 3.063,0.906 0.26,0.271 10 *1 0.698,1.469 0.958,1.74 0.26,0.271 10 *2 4.677,1.76 4.938,2.031 0.26,0.271 10 *3 1.531,6 1.792,6.229 0.26,0.229 10 (9) 2.406,5.99 2.708,6.219 0.302,0.229 10 (10) 1.26,3.302 1.521,3.531 0.26,0.229 10 (1) 0.469,2.635 0.729,2.865 0.26,0.229 10 (A) 5.865,3.302 6.125,3.531 0.26,0.229 10 (4) 2.594,3.302 2.854,3.531 0.26,0.229 10 (2) 4.521,3.302 4.781,3.531 0.26,0.229 10 (3) 1.521,7.208 1.781,7.438 0.26,0.229 10 *6 2.479,7.188 2.74,7.417 0.26,0.229 10 *7 4.667,7.198 4.927,7.427 0.26,0.229 10 *8 5.615,7.198 5.875,7.427 0.26,0.229 10 *9 4.615,5.99 4.917,6.219 0.302,0.229 10 (11) 5.531,6 5.854,6.229 0.323,0.229 10 (12) 2.458,4.813 2.719,5.042 0.26,0.229 10 (6) 1.531,4.813 1.792,5.042 0.26,0.229 10 (5) 4.667,4.802 4.927,5.031 0.26,0.229 10 (7) 5.573,4.802 5.833,5.031 0.26,0.229 10 (8) 3.313,6.948 3.573,7.219 0.26,0.271 10 *5 3.729,6.063 3.99,6.333 0.26,0.271 10 *4 3.375,6.073 3.635,6.344 0.26,0.271 10 *4 3.802,6.938 4.063,7.208 0.26,0.271 10 *5 0.469,4.104 0.729,4.333 0.26,0.229 10 (E) 1.979,4.531 2.24,4.76 0.26,0.229 10 (F) 1.938,2.625 2.198,2.854 0.26,0.229 10 (B) 6.646,2.635 6.906,2.865 0.26,0.229 10 (D) 5.167,2.615 5.427,2.844 0.26,0.229 10 (C) 6.646,4.104 6.906,4.333 0.26,0.229 10 (H) 5.104,4.531 5.365,4.76 0.26,0.229 10 (G) 0.469,5.292 0.729,5.521 0.26,0.229 10 (I) 2.073,6.354 2.333,6.583 0.26,0.229 10 (J) 6.646,5.302 6.906,5.531 0.26,0.229 10 (L) 5.031,6.385 5.292,6.615 0.26,0.229 10 (K)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Left Side)
*7 Rear Brake Caliper (Right Side) *8 Rear Brake Caliper (Left Side)
*9 Front Brake Caliper (Right Side) - -



iii.

Each valve operates as shown below:

Item Port TRC Not Activated TRC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON* ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
Front Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9), (12) (I), (L) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Brake Wheel Cylinder Pressure - - - Increased Held Reduced
Rear Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10), (11) (J), (K) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure - - - - - -
Pump OFF ON ON ON

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.



d.

VSC

i.

VSC, by way of solenoid valves, controls the fluid pressure generated by the pump and applies it to each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, understeer and oversteer tendencies are controlled.

X106792
0.656,2.385 1.885,2.698 1.229,0.313 10 false Speed Sensor (4) 0.281,5.625 1.917,5.969 1.635,0.344 10 false Airbag Sensor Assembly 5.427,5.219 6.615,5.563 1.188,0.344 10 false Steering Sensor 3.125,0.542 4.094,0.885 0.969,0.344 10 false Solenoid Relay 3.083,2.396 4.26,2.969 1.177,0.573 10 false Skid Control ECU 3.208,3.583 4.063,3.927 0.854,0.344 10 false Motor Relay 5.271,0.375 6.656,0.844 1.385,0.469 10 false Master Cylinder Cut Solenoid Valve (2) 5.208,1.188 6.74,1.75 1.531,0.563 10 false Reservoir Cut Solenoid Valve (2) 5.094,1.979 6.875,2.469 1.781,0.49 10 false Pressure Holding Solenoid Valve (4) 5.031,2.781 6.906,3.292 1.875,0.51 10 false Pressure Reduction Solenoid Valve (4) 5.51,3.594 6.406,3.885 0.896,0.292 10 false Pump Motor 5.146,4.083 6.75,4.615 1.604,0.531 10 false Master Cylinder Pressure Sensor 5.042,5.958 6.896,6.26 1.854,0.302 10 false Combination Meter Assembly 5.396,4.927 7,5.208 1.604,0.281 10 false Brake Actuator Assembly 5.302,6.438 6.688,6.76 1.385,0.323 10 false Brake Warning Light 5.344,6.844 6.604,7.188 1.26,0.344 10 false ABS Warning Light 5.375,7.24 6.688,7.542 1.313,0.302 10 false Slip Indicator Light 0.5,6.958 2.177,7.604 1.677,0.646 10 false Throttle Body with Motor Assembly 3.417,7.677 3.854,8 0.438,0.323 10 false ECM 0.781,7.76 1.74,8.094 0.958,0.333 10 false Throttle Motor 0.49,8.156 2.094,8.49 1.604,0.333 10 false Throttle Position Sensor 2.698,5.177 3.552,5.552 0.854,0.375 10 false CAN (V Bus) 0.281,6.313 1.917,6.656 1.635,0.344 10 false - Acceleration Sensor 0.281,5.99 1.917,6.333 1.635,0.344 10 false - Yawrate Sensor


ii.

In understeer restraining control, the skid control ECU controls engine output and applies the brakes of front and rear wheels on the inside of the turn. Also, depending on whether the brakes are applied and the vehicle condition, there are circumstances in which the brake of a specific wheel may not be applied even if it was targeted for braking. The diagram below shows the hydraulic circuit in pressure increase mode, as it restrains an understeer tendency while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned ON/OFF according to the ABS and EBD operation pattern.

VSC Operation (Understeer Restraining Control)
X105900C02
2.938,0.708 3.604,0.708 true 4.792,1.833 5.458,1.833 true 3.302,5.24 3.448,5.406 3.448,5.406 3.448,6.052 true 3.938,5.24 3.802,5.406 3.802,5.406 3.802,6.052 true 3.375,6.938 3.375,6.573 true 3.875,6.948 3.875,6.583 true 0.677,2.698 1.344,2.698 true 0.677,4.167 1.604,4.167 true 2.146,2.698 2.656,2.698 true 4.604,2.698 5.115,2.698 true 5.927,2.698 6.615,2.698 true 5.656,4.177 6.615,4.177 true 2.052,4.521 2.052,4.177 2.052,4.177 2.521,4.177 true 5.188,4.51 5.188,4.177 5.188,4.177 4.74,4.177 true 0.656,5.375 1.604,5.375 true 2.167,6.354 2.167,5.385 2.167,5.385 2.542,5.385 true 5.656,5.365 6.615,5.365 true 5.104,6.344 5.104,5.375 5.104,5.375 4.74,5.375 true 2.76,0.625 3.021,0.896 0.26,0.271 10 *1 0.688,1.458 0.948,1.729 0.26,0.271 10 *2 4.615,1.75 4.875,2.021 0.26,0.271 10 *3 1.531,5.979 1.792,6.208 0.26,0.229 10 (9) 2.406,5.979 2.708,6.208 0.302,0.229 10 (10) 1.26,3.313 1.521,3.542 0.26,0.229 10 (1) 0.469,2.625 0.729,2.854 0.26,0.229 10 (A) 5.865,3.313 6.125,3.542 0.26,0.229 10 (4) 2.594,3.313 2.854,3.542 0.26,0.229 10 (2) 4.521,3.302 4.781,3.531 0.26,0.229 10 (3) 1.521,7.188 1.781,7.417 0.26,0.229 10 *6 2.458,7.198 2.719,7.427 0.26,0.229 10 *7 4.667,7.208 4.927,7.438 0.26,0.229 10 *8 5.625,7.208 5.885,7.438 0.26,0.229 10 *9 4.615,5.979 4.917,6.208 0.302,0.229 10 (11) 5.531,5.99 5.854,6.219 0.323,0.229 10 (12) 2.458,4.802 2.719,5.031 0.26,0.229 10 (6) 1.531,4.792 1.792,5.021 0.26,0.229 10 (5) 4.677,4.792 4.938,5.021 0.26,0.229 10 (7) 5.573,4.792 5.833,5.021 0.26,0.229 10 (8) 3.313,6.948 3.573,7.219 0.26,0.271 10 *5 3.729,6.052 3.99,6.323 0.26,0.271 10 *4 3.375,6.063 3.635,6.333 0.26,0.271 10 *4 3.802,6.948 4.063,7.219 0.26,0.271 10 *5 0.469,4.094 0.729,4.323 0.26,0.229 10 (E) 1.979,4.521 2.24,4.75 0.26,0.229 10 (F) 1.938,2.615 2.198,2.844 0.26,0.229 10 (B) 6.646,2.635 6.906,2.865 0.26,0.229 10 (D) 5.167,2.625 5.427,2.854 0.26,0.229 10 (C) 6.646,4.104 6.906,4.333 0.26,0.229 10 (H) 5.104,4.521 5.365,4.75 0.26,0.229 10 (G) 0.469,5.302 0.729,5.531 0.26,0.229 10 (I) 2.083,6.365 2.344,6.594 0.26,0.229 10 (J) 6.656,5.302 6.917,5.531 0.26,0.229 10 (L) 5.021,6.375 5.281,6.604 0.26,0.229 10 (K)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Left Side)
*7 Rear Brake Caliper (Right Side) *8 Rear Brake Caliper (Left Side)
*9 Front Brake Caliper (Right Side) - -



iii.

Each valve operates as shown below:

Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON* ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
Front Brakes Pressure Holding Solenoid Valve (5) (E) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
(8) (H) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9) (I) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
(12) (L) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Brake Wheel Cylinder Pressure Right - - - Increased Held Reduced
Left - - - - - -
Rear Brakes Pressure Holding Solenoid Valve (6) (F) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
(7) (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10) (J) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
(11) (K) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Brake Wheel Cylinder Pressure Right - - - Increased Held Reduced
Left - - - - - -
Pump OFF ON ON ON

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.


iv.

In oversteer restraining control, the skid control ECU applies the brakes of the front and rear wheels on the outside of the turn. Also, depending on whether the brakes are applied and the vehicle condition, the brake of a specific wheel may not be applied even if it was targeted for braking. The diagram below shows the hydraulic circuit in pressure increase mode, as it restrains an oversteer tendency while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned ON/OFF according to the ABS and EBD operation patterns.

VSC Operation (Oversteer Restraining Control)
X105901C02
2.958,0.719 3.625,0.719 true 4.844,1.844 5.51,1.844 true 3.302,5.24 3.448,5.406 3.448,5.406 3.448,6.052 true 3.927,5.229 3.792,5.396 3.792,5.396 3.792,6.042 true 3.375,6.938 3.375,6.573 true 3.865,6.938 3.865,6.573 true 0.677,2.708 1.344,2.708 true 0.677,4.177 1.604,4.177 true 2.146,2.698 2.656,2.698 true 4.604,2.698 5.115,2.698 true 5.927,2.698 6.615,2.698 true 5.656,4.177 6.615,4.177 true 2.052,4.521 2.052,4.177 2.052,4.177 2.521,4.177 true 5.188,4.521 5.188,4.188 5.188,4.188 4.74,4.188 true 0.656,5.375 1.604,5.375 true 2.146,6.365 2.146,5.396 2.146,5.396 2.521,5.396 true 5.656,5.365 6.615,5.365 true 5.104,6.354 5.104,5.385 5.104,5.385 4.74,5.385 true 2.802,0.635 3.063,0.906 0.26,0.271 10 *1 0.688,1.469 0.948,1.74 0.26,0.271 10 *2 4.698,1.771 4.958,2.042 0.26,0.271 10 *3 1.531,6 1.792,6.229 0.26,0.229 10 (9) 2.438,5.979 2.74,6.208 0.302,0.229 10 (10) 1.26,3.313 1.521,3.542 0.26,0.229 10 (1) 0.469,2.646 0.729,2.875 0.26,0.229 10 (A) 5.865,3.302 6.125,3.531 0.26,0.229 10 (4) 2.594,3.313 2.854,3.542 0.26,0.229 10 (2) 4.521,3.313 4.781,3.542 0.26,0.229 10 (3) 1.521,7.198 1.781,7.427 0.26,0.229 10 *6 2.469,7.188 2.729,7.417 0.26,0.229 10 *7 4.667,7.198 4.927,7.427 0.26,0.229 10 *8 5.625,7.188 5.885,7.417 0.26,0.229 10 *9 4.615,5.979 4.917,6.208 0.302,0.229 10 (11) 5.531,6 5.854,6.229 0.323,0.229 10 (12) 2.458,4.802 2.719,5.031 0.26,0.229 10 (6) 1.531,4.802 1.792,5.031 0.26,0.229 10 (5) 4.667,4.802 4.927,5.031 0.26,0.229 10 (7) 5.573,4.792 5.833,5.021 0.26,0.229 10 (8) 3.313,6.938 3.573,7.208 0.26,0.271 10 *5 3.729,6.052 3.99,6.323 0.26,0.271 10 *4 3.375,6.063 3.635,6.333 0.26,0.271 10 *4 3.802,6.948 4.063,7.219 0.26,0.271 10 *5 0.469,4.104 0.729,4.333 0.26,0.229 10 (E) 1.979,4.521 2.24,4.75 0.26,0.229 10 (F) 1.938,2.625 2.198,2.854 0.26,0.229 10 (B) 6.646,2.646 6.906,2.875 0.26,0.229 10 (D) 5.167,2.625 5.427,2.854 0.26,0.229 10 (C) 6.646,4.104 6.906,4.333 0.26,0.229 10 (H) 5.104,4.531 5.365,4.76 0.26,0.229 10 (G) 0.469,5.302 0.729,5.531 0.26,0.229 10 (I) 2.083,6.385 2.344,6.615 0.26,0.229 10 (J) 6.646,5.281 6.906,5.51 0.26,0.229 10 (L) 5.021,6.375 5.281,6.604 0.26,0.229 10 (K)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Left Side)
*7 Rear Brake Caliper (Right Side) *8 Rear Brake Caliper (Left Side)
*9 Front Brake Caliper (Right Side) - -



v.

Each valve operates as shown below:

Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON* ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
Front Brakes Pressure Holding Solenoid Valve (5) (E) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
(8) (H) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9) (I) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
(12) (L) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - - - - -
Left - - - Increased Held Reduced
Rear Brakes Pressure Holding Solenoid Valve (6) (F) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
(7) (G) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10) (J) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
(11) (K) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Brake Wheel Cylinder Pressure Right - - - - - -
Left - - - Increased Held Reduced
Pump OFF ON ON ON

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.