Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › 2011.10–2014.05
NM19V0EQ _56 Audio / Visual / Telematics _014269 PARK ASSIST / MONITORING _0072872 PARKING ASSIST MONITOR SYSTEM CO CONTROL F

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  CONTROL  PARKING ASSIST MONITOR CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Rear Television Camera Assembly Captures images of the area behind the vehicle and outputs video signals to the navigation receiver assembly.
Navigation Receiver Assembly Displays the image of the area behind the vehicle sent from the rear television camera assembly using the multi display. The image is combined with the parking assist guide lines that are calculated based on signals from the spiral with sensor cable sub-assembly (steering angle sensor).
Park/Neutral Position Switch Assembly Sends a shift position signal to the navigation receiver assembly.
Steering Sensor Detects the angle of the steering wheel and sends the resulting signals to the navigation receiver assembly.
Combination Meter Assembly Transmits the vehicle speed signal to the navigation receiver assembly.
Luggage Compartment Door Lock Assembly
- Luggage Compartment Door Courtesy Switch
Sends the luggage compartment door courtesy switch signal to the navigation receiver assembly via the main body ECU (multiplex network body ECU).


SYSTEM CONTROL


a.

The parking assist monitor system operates when both of the following conditions are met:

·

Ignition switch ON.

·

Shift lever in R.




FUNCTION


a.

Area Displayed on Screen

i.

On the display, objects on the right of the vehicle appear on the right side of the display panel, and objects on the left of the vehicle appear on the left side of the display panel.


ii.

The rear television camera uses a wide-angle lens. The perceived distance from images that appear on the screen differs from the actual distance.

Y113055

NOTICE:

The area displayed on the screen may vary according to vehicle status or road conditions. The area covered by the rear television camera assembly is limited. The rear television camera assembly does not show objects close to either corner of the bumper or show the area under the bumper.




b.

Warning Message

i.

A warning message appears at the bottom or center of the screen under the following conditions. The warning message appears in the same language that has been selected by the language selector of the multi-display.

Messages Appearing at Bottom of Screen
Warning Message Condition
Check surroundings for safety. This message always appears during system operation.
System initializing. This message appears when the steering wheel is operated while the battery terminal (-) is disconnected and then the terminal is reconnected.
Guidance is unavailable. This message appears if there is a malfunction in this system.

Message Appearing at Center of Screen
Warning Message Condition
System not ready. This message appears if the system is not initialized.



c.

Calibration Following Parts Replacement

i.

The items listed below must always be adjusted whenever one of the following conditions occurs. For details, refer to the Repair Manual.

Adjustment Items Condition
Neutral steering point in memory System initializing is displayed.
Steering angle setting
·

After spiral cable sub-assembly is removed and installed or after connector is disconnected and reconnected, system initializing is displayed.

·

After steering sensor is removed and installed or after connector is disconnected and reconnected, system initializing is displayed.

·

Steering sensor replacement.


Camera optical axis adjustment
·

Vehicle height has changed due to replacement of suspension parts or tires.

·

The installation angle of the rear television camera assembly has changed.


Parking assist monitor system initialization Navigation receiver assembly is replaced.




FAIL-SAFE


a.

The table below indicates the malfunction detection items for the components in this system.

Malfunction Parts Detection Item Function
Steering Sensor
·

Transmission of sensor malfunction signal

·

Open circuit in sensor signal

·

Communication malfunction between the steering sensor and navigation receiver assembly


Displays "Guidance is unavailable"
Transmission of signal to indicate that neutral steering point correction is incomplete Displays "System initializing"
Rear Television Camera Assembly Transmission of camera malfunction signal Stop signal reception and displays a dark screen
Navigation Receiver Assembly Malfunction of navigation receiver assembly Stops system operation



DIAGNOSIS


a.

The navigation receiver assembly is equipped with a diagnosis function which can display a diagnosis menu for the parking assist monitor system. The method for entering the diagnosis menu screen is the same as the method used for the multi-display. For details, refer to the Repair Manual.