Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2011.10–2015.04
NM19V0EQ _56 Audio / Visual / Telematics _014269 PARK ASSIST / MONITORING _0072870 BLIND SPOT MONITOR SYSTEM CO CONTROL F

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  CONTROL  BLIND SPOT MONITOR CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Blind Spot Monitor Sensor LH and RH
·

Radiates radar waves from the blind spot monitor sensor to the blind spot sensor detection area, uses the reflected millimeter waves for detecting the presence of a vehicle, the vehicle-to-vehicle distance, and the relative speed, and then transmits this information to the built-in signal processing circuit.

·

The signal processing circuit determines if a vehicle is present, and illuminates or blinks the outer rear view mirror indicator light accordingly.


Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly) Pressing the blind spot monitor main switch (warning canceling switch assembly) turns the blind spot monitor system on or off.
Outer Rear View Mirror Assembly LH and RH Outer Rear View Mirror Indicator Light
·

Illuminates to inform the driver that a vehicle has been detected in the blind spot detection area.

·

Flashes to inform the driver when the turn signal lever is operated if a vehicle has been detected in the blind spot detection area.


Combination Meter Assembly Transmits the turn switch signal to the blind spot monitor sensor LH and RH.
Combination Meter Assembly Blind Spot Monitor Warning Light When the blind spot monitor sensors detect a malfunction or determine that control is not possible, the light illuminates to warn the driver.
Steering Sensor Transmits the steering angle signal to the blind spot monitor sensor LH and RH.
Skid Control ECU Transmits the vehicle speed signal to the blind spot monitor sensor LH and RH.
Main Body ECU (Multiplex Network Body ECU) Transmits the destination signal to the blind spot monitor sensor LH and RH.
Outer Mirror Control ECU Assembly LH and RH Transmits the indicator light signal to the outer rear view mirror assembly.
Network Gateway ECU Transmits data between the CAN V bus and the CAN sub bus 2.
ECM Transmits the reverse signal to the blind spot monitor sensor LH and RH.


SYSTEM CONTROL


a.

Operating Condition

i.

The blind spot monitor system operates when both of the following conditions are met:

·

The blind spot monitor main switch (warning canceling switch assembly) is on.

·

The vehicle speed is greater than about 40 km/h (25 mph).




b.

The blind spot monitor system can detect vehicles in its detection areas.

i.

The detection areas formed by the blind spot monitor sensor LH and RH are as shown below.

Y110644C01
2.854,0.292 3.083,0.479 0.229,0.188 10 *b 1.948,1.01 2.177,1.198 0.229,0.188 10 *a 1.948,2.563 2.177,2.75 0.229,0.188 10 *a 5.031,1.552 5.26,1.74 0.229,0.188 10 *d 5.042,2.146 5.271,2.333 0.229,0.188 10 *d 3.479,0.281 3.708,0.469 0.229,0.188 10 *c 2.906,3.396 3.135,3.583 0.229,0.188 10 *b 3.479,3.375 3.708,3.563 0.229,0.188 10 *c
*a 3.5 m (11.5 ft) *b 3.0 m (9.8 ft)
*c 1 m (3.3 ft) *d 0.5 m (1.6 ft)
V100144

Detection Area - -



ii.

This vehicle is overtaken by another vehicle in the adjacent lane.

Y110645
4.281,1.771 4.281,2.344 true 4.219,2.396 4.448,2.583 0.229,0.188 10 *1
*1 This Vehicle - -
V100135

Vehicle Speed (Fast)
V100136

Vehicle Speed (Slow)
V100144

Detection Area - -



iii.

When another vehicle enters the detection area of this vehicle due to a lane change.

Y110646
2.104,1.958 2.104,2.26 true 5.604,1.917 5.604,2.208 true 1.667,2.354 1.896,2.542 0.229,0.188 10 *a 2.042,2.292 2.271,2.479 0.229,0.188 10 *1 5.531,2.25 5.76,2.438 0.229,0.188 10 *1 5.01,2.354 5.24,2.542 0.229,0.188 10 *b
*1 This Vehicle - -
*a Other vehicle enters the detection area during lane change (merge in) (Type 1). *b Other vehicle enters the detection area during lane change (merge in) (Type 2).
V100135

Motion direction of this vehicle
V100136

Motion direction of other vehicle
V100144

Detection Area - -




c.

According to operation conditions, the blind spot monitor system promotes safety confirmation by using the outer rear view mirror indicator light to inform the driver that another vehicle has entered the blind spot monitor sensor detection area of this vehicle.


d.

The outer rear view mirror indicator light informs the driver that a vehicle is present in the blind spot detection area by illuminating when the turn signal switch is not operated, and by flashing when a vehicle is present and the turn signal switch is operated.

Y113422
5.25,0.292 6.865,0.719 1.615,0.427 10 false Outer Mirror Control ECU Assembly RH 0.302,0.302 1.906,0.708 1.604,0.406 10 false Outer Mirror Control ECU Assembly LH 0.396,2.625 1.844,2.99 1.448,0.365 10 false Outer Rear View Mirror Assembly LH 0.375,1.813 1.833,2.323 1.458,0.51 10 false Outer Rear View Mirror Indicator Light 5.323,2.646 6.802,2.99 1.479,0.344 10 false Outer Rear View Mirror Assembly RH 0.188,5.458 2.063,5.854 1.875,0.396 10 false Combination Meter Assembly 0.229,5.813 2.094,6.208 1.865,0.396 10 false - Turn Signal Switch Signal 2.844,5.469 4.427,5.865 1.583,0.396 10 false Network Gateway ECU 3.75,5.031 4.896,5.313 1.146,0.281 10 false CAN (Sub Bus 2) 3.198,6.802 4.177,7.135 0.979,0.333 10 false CAN (V Bus) 5.302,5.458 6.708,5.854 1.406,0.396 10 false Skid Control ECU 5.156,5.76 6.729,6.156 1.573,0.396 10 false - Vehicle Speed Signal 5.354,7.26 6.51,7.594 1.156,0.333 10 false Steering Sensor 2.406,2.063 3.135,3.146 0.729,1.083 10 false Blind Spot Monitor Sensor LH 4.083,2.063 4.813,3.146 0.729,1.083 10 false Blind Spot Monitor Sensor RH 5.229,3.802 6.938,4.438 1.708,0.635 10 false Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly) 5.344,1.813 6.792,2.292 1.448,0.479 10 false Outer Rear View Mirror Indicator Light



DIAGNOSIS


a.

The blind spot monitor system is equipped with a diagnosis function which can illuminate the blind spot monitor warning light in the combination meter assembly. For details, refer to the Repair Manual.