Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
NM19V0EQ _59 Vehicle Exterior _014279 WINDOW / GLASS _0072890 POWER WINDOW CONTROL SYSTEM CO CONTROL F

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  CONTROL  POWER WINDOW CONTROL  


SYSTEM CONTROL


a.

The power window control system has the following functions:

Function Outline Customizable*1
Manual Up-and-down For driver door:
Function that causes the window to go up while the power window regulator master switch assembly is being pulled halfway up and to go down while pushed halfway down. The window stops as soon as the switch is released.
For passenger door:
Function that causes the window to go up while the power window regulator switch assembly is being pulled up and to go down while pushed down. The window stops as soon as the switch is released.
Standard (Not Customizable)
Driver door auto up-and-down function*2 Function that enables the driver door window to be fully opened or closed by one full pull or push of the power window regulator master switch assembly. Standard (Not Customizable)
Driver door auto down function*3 Function that enables the driver door window to be fully opened by one full push of the power window regulator master switch assembly. Standard (Not Customizable)
Jam Protection (Driver Door) The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the window during one-touch auto-up operation or power up operation. Standard (Not Customizable)
Remote Control (All Doors) The power window regulator master switch assembly can control the up-and-down operation of the windows. Standard (Not Customizable)
Window Lock Operation of the 3 passenger windows is disabled when the window lock switch is pressed. Standard (Not Customizable)
Key Off Operation
·

This function makes it possible to operate the power windows for approximately 43 seconds after the ignition switch is turned off, if either front door is not opened.

·

If the window lock switch is off, the windows can be operated using any of the power window regulator switch assemblies. If the window lock switch is on, the windows cannot be operated.

·

If the driver door or front passenger door is opened during automatic window operation while the key-off operation function is on, the window will stop operating.


Standard (Not Customizable)
Key-linked Up-and-down*5 When the electrical key transmitter sub-assembly is not in the interior detection area*6, the driver door is locked, and the door control transmitter assembly*7 or mechanical key*6 in the driver door is turned and maintained in the lock direction for 2.3 seconds or more, the main body ECU (multiplex network body ECU) activates the power window motors to raise all door windows while the door control transmitter assembly*7 or mechanical key*6 is turned.
Similarly, when the driver door is unlocked, turning and maintaining the driver door key cylinder in the unlock direction for 1.5 seconds or more will cause all door windows to be lowered.
*4
Transmitter-linked Down*5,*8 When the certification ECU (smart key ECU assembly) receives an unlock signal from the transmitter for longer than 2.4 seconds, the main body ECU (multiplex network body ECU) controls their power window motors in accordance with the signal to open the windows. *4

*1: Customizable settings can be turned on or off. For details, refer to the Repair Manual.

*2: Models with jam protection function on driver door

*3: Models without jam protection function on driver door

*4: Default setting is off.

*5: RHD Models

*6: Models with smart entry and start system

*7: Models without smart entry and start system

*8: Models with wireless door lock control system


HINT:

The ECU built into each power window motor stores the initial position of its door window. The initial position is not cleared even if auxiliary battery terminals, fuses or the power window motor connector is disconnected. However, after removing or reinstalling window components, or replacing the power window regulator sub-assembly or power window regulator motor, the stored initial position data must be cleared and/or initialization must be performed. For details, refer to the Repair Manual.



b.

Jam Protection Function

i.

The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the door window during one-touch auto up operation or power up operation.


ii.

The operation of the jam protection function is described below.

Door Window Position from Full Close Operation
200 mm (7.87 in.) or more Down operation of 125 mm (4.93 in.) or 2.5 seconds
200 mm (7.87 in.) or less Down operation until door window downward movement of 200 mm (7.87 in.) is reached, or 5 seconds elapses.


iii.

The magnet and Hall IC in the power window motor are used to enable power window jam protection.

Y101660
3.125,1.292 3.125,0.292 3.125,0.292 2.719,0.292 true 3.792,1.552 3.792,0.302 3.792,0.302 4.146,0.302 true 3.146,1.635 3.146,2.479 true 2.521,0.208 2.719,0.438 0.198,0.229 10 *1 4.198,0.219 4.396,0.448 0.198,0.229 10 *2 3.073,2.5 3.271,2.688 0.198,0.188 10 *3
*1 Hall IC *2 Worm Gear
*3 Magnet - -



iv.

The Hall IC converts the changes in the magnetic flux that occur through the rotation of the magnet into pulse signals and outputs them to the ECU built-into the power window motor.


v.

To control the jam protection function, the ECU determines the amount of movement and jamming of the window glass based on the pulse signal A from the Hall IC; and judges the direction of the window glass movement based on the phase difference between the pulses from Hall IC signals A and B.

Y100062
0.115,0.073 3.125,0.365 3.01,0.292 12 Judgment of Movement and Jamming: 0.281,0.854 1.292,1.073 1.01,0.219 10 Hall IC Signal 0.115,2.469 2.698,2.729 2.583,0.26 12 Judgment of Movement Direction: 0.281,3.24 1.292,3.458 1.01,0.219 10 Hall IC Signal A 0.281,4.104 1.427,4.323 1.146,0.219 10 Hall IC Signal B 1.479,1.792 2.031,2.01 0.552,0.219 10 Normal 4.51,1.771 5.24,1.99 0.729,0.219 10 Jammed 2.083,4.417 2.635,4.635 0.552,0.219 10 DOWN 5.146,4.417 5.542,4.635 0.396,0.219 10 UP




FAIL-SAFE


a.

If the Hall IC in the power window motor (driver) malfunctions, some power window functions will be prohibited for fail-safe mode.

i.

The power window operates when the power window switch is fully pushed down or pulled up and held in that position.




DIAGNOSIS


a.

When the power window ECU detects the following condition, it switches to fail-safe mode.

i.

An abnormality in the Hall IC that detects the position, speed and direction of the window.