OUTLINE
Exterior Lights
The exterior lights consist of the following:
| *A | Models with Built-in Type Side Turn Signal Lights | *B | Models with Front Fog Lights |
| *1 | Side Turn Signal Light RH | *2 | Side Turn Signal Light LH |
| *3 | Fog Light Assembly RH | *4 | Headlight Assembly RH |
| *5 | Headlight Assembly LH | *6 | Fog Light Assembly LH |
| *7 | Front Turn Signal Light | *8 | High Beam |
| *9 | Low Beam | - | - |
| *1 | High Mounted Stop Light (Center Stop Light Set) | *2 | Rear Combination Light Assembly LH |
| *3 | Rear Combination Light Assembly RH | *4 | Rear Light Assembly LH |
| *5 | Rear Light Assembly RH | *6 | License Plate Light |
| *7 | Back-up Light | *8 | Rear Turn Signal Light |
| *9 | Taillight and Stop Light | - | - |
Automatic High Beam System
The automatic high beam system detects lights in front of the vehicle and automatically changes between high beams and low beams to support the driver during night driving.
Automatic Light Control System
When the dimmer switch is in the AUTO position, the light control sensor detects the ambient light level and automatically turns the headlights, taillights or license plate lights on or off accordingly.
This system is controlled by the main body ECU (multiplex network body ECU).
Light Auto Turn-off System
The light auto turn-off system is used to prevent the driver from leaving the vehicle with the headlights, front fog lights*, taillights or license plate lights on.
*: Models with front fog lights
SPECIFICATION
| Light | Type | Wattage | |
|---|---|---|---|
| Headlight Assembly | High Beams | Halogen Bulb | 60 |
| Low Beams | Halogen Bulb | 55 | |
| Front Turn Signal Lights | Bulb | 21 | |
| Side Turn Signal Light Assembly (LH, RH)*1 | Bulb | 5 | |
| Front Fog Light Assembly*2 | Halogen Bulb | 55 | |
| Rear Light Assembly | Taillights/Stop Lights | Bulb | 21/5 |
| Rear Combination Light Assembly | Rear Turn Signal Lights | Bulb | 21 |
| Backup Light | Bulb | 16 | |
| High Mounted Stop Light (Center Stop Light Set) | LED x 4 | 0.4 | |
| License Plate Light | Bulb | 5 | |
*1: Models with built-in type side turn signal lights
*2: Models with front fog lights
PRECAUTION
Automatic High Beam System
The automatic high beam system is a system that helps ensure visibility by automatically turning the high beams on and off.
However, due to control limitations of the automatic high beam system, it may be necessary to manually turn the high beams on and off. When driving, for safety reasons, make sure to change the high beams and low beams manually according to the driving conditions.
Under the following conditions, the automatic high beam system might not detect other vehicles or lights correctly, or the high beams might cause glare or flash pedestrians or the occupants of other vehicles. Manual operation should be used.
| Factor | Condition |
|---|---|
| Weather/Climate | When driving in bad weather (rain, snow, fog, sandstorms, etc.). |
| Front Windshield | ·
When the windshield is not clear (ice, snow or frost on the glass). ·
When the windshield is dirty (sand, mud, water stain or bugs on the glass). ·
When the windshield is cracked. ·
When the windshield is fogged-up. ·
When the windshield has a film attached. ·
When an object on the instrument panel reflects off of the front glass. ·
When any other abnormal conditions exist with the front glass. |
| Inner Rear View Mirror (Automatic High Beam Sensor) | ·
When a parking tag, wide angle rear view mirror adaptor or other accessory is mounted on the inner rear view mirror assembly. ·
When the inner rear view mirror or its built-in camera is deformed. ·
When the automatic high beam sensor in the inner rear view mirror is dirty. ·
When any other abnormal conditions exist with the inner rear view mirror or its built-in automatic high beam sensor. |
| Nearby Vehicles or Lights | ·
When lights similar to headlights or taillights are in the vicinity of the vehicle. ·
When a nearby vehicle has no lights or its lights are off. ·
When a vehicle in front has misaligned lights, or its lights are changing color. ·
When a vehicle in front has extremely dirty headlights or taillights. |
| Road Conditions | ·
When driving in an area where the conditions often change between bright and dark. ·
When driving on a road with many uphill and downhill slopes. ·
When driving on a winding road or around a sharp curve. ·
When driving on a bumpy road (cobblestone pavement, gravel road, rough unpaved road, etc.). ·
When highly reflective objects are in front of the vehicle (mirrors, road signs, etc.). |
| Own Vehicle | ·
When the headlights are damaged, deformed or dirty. ·
When the vehicle posture is abnormal (posture has changed due to the vehicle being fully loaded, a trailer being towed, road conditions etc.). ·
When the vehicle has other malfunctions or if the vehicle has been modified. |
| Automatic High Beam System | Malfunction:
·
When the automatic high beam indicator light on the combination meter assembly is off or is blinking. ·
When the indicator light on the inner rear view mirror assembly is blinking. Others: ·
When the automatic high beam system does not seem to be changing between the high beams and low beams properly. ·
When the automatic high beam system is frequently changing between the high beams and low beams. ·
When the glare from the high beams would disturb pedestrians or the drivers of other vehicles. |
Ignition Switch Expressions
The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.
| Expression | Ignition Switch
(Position) |
Engine Switch
(Condition) |
|---|---|---|
| Ignition Switch off | LOCK | Off |
| Ignition Switch ACC | ACC | On (ACC) |
| Ignition Switch ON | ON | On (IG) |
| Engine Start | START | Start |