FUNCTION OF MAIN COMPONENTS
The main components in the dynamic radar cruise control system have the following functions:
| Component | Function | ||
|---|---|---|---|
|
*: Models with shift paddle switch (transmission shift switch assembly) |
|||
| Windshield Wiper Motor Assembly | Transmits the windshield wiper switch assembly information to the driving support ECU assembly. | ||
| Millimeter Wave Radar Sensor Assembly | ·
Radiates millimeter radar waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance, and the relative speed, and then transmits this information to the driving support ECU assembly. ·
Sounds the skid control buzzer assembly according to signals from the driving support ECU assembly. |
||
| Driving Support ECU Assembly | While the system is in vehicle-to-vehicle distance control mode, the driving support ECU assembly detects the vehicle ahead based on signals from the millimeter wave radar sensor. Then, the driving support ECU assembly calculates the acceleration or deceleration rate required in order to attain the target vehicle-to-vehicle distance, and outputs a request signal to the ECM and/or skid control ECU (brake actuator assembly). | ||
| Cruise Control Switch | ON-OFF Button | Turns the cruise control system on and off. | |
| MODE Switch | Switches the control mode between constant speed control mode and vehicle-to-vehicle distance mode. | ||
| CANCEL Switch | A cancel signal is output to the ECM when this switch is operated. | ||
| +RES Switch | The acceleration function and resuming of a preset speed can be performed by operating this switch. A signal is output to the ECM when this switch is operated. | ||
| -SET Switch | The deceleration function and vehicle speed setting resume signals are output to the ECM when this switch is operated. | ||
| Steering Pad Switch Assembly | Vehicle-to-vehicle Distance Control Switch | While the system is in vehicle-to-vehicle distance control mode, the driver can operate the vehicle-to-vehicle distance control switch to select one of three stages of vehicle-to-vehicle distance: long, middle, and short. | |
| ECM | ·
Controls the dynamic radar cruise control system in accordance with signals from the switches, sensors, skid control ECU and driving support ECU assembly. ·
If the ECM detects a malfunction in the cruise control system, it will store Diagnostic Trouble Codes (DTCs). |
||
| Brake Actuator Assembly | Skid Control ECU | ·
While the system is operating in vehicle-to-vehicle distance control mode, the skid control ECU operates the brake actuator in accordance with the brake request signal received from the ECM. ·
Applies the brakes in accordance with signals from the skid control ECU. |
|
| Combination Meter Assembly | Multi-information Display | Cruise Control Indicator (Constant Speed Control Mode) | ·
Based on a cruise control indicator operation signal sent by the ECM, the combination meter assembly illuminates the cruise control indicator when the cruise control system has been turned on using the ON-OFF button on the cruise control switch and constant speed control mode has been selected. ·
Based on a cruise control indicator operation signal sent by the ECM, the combination meter assembly turns off the cruise control indicator if a malfunction occurs in the cruise control system. |
| Cruise Control Indicator (Vehicle-to-vehicle Distance Control) | ·
Based on a cruise control indicator operation signal sent by the ECM, the combination meter assembly illuminates the cruise control indicator when the cruise control system has been turned on using the ON-OFF button on the cruise control switch. ·
Based on a cruise control indicator operation signal sent by the ECM, the combination meter assembly turns off the cruise control indicator if a malfunction occurs in the cruise control system. |
||
| Cruise Control SET Indicator | Illuminates when the vehicle speed is set. | ||
| Multi-information Display | During dynamic radar cruise control operation, the multi-information display receives signals from the ECM in order to display the system conditions. | ||
| Master Warning Light | Illuminates when there is a malfunction in the system. | ||
| Buzzer | If the ECM or driving support ECU assembly detects automatic cancel or warning signals while the vehicle is operating under cruise control, this buzzer sounds to inform the driver. | ||
| Throttle Body with Motor Assembly | Throttle Control Motor | Adjusts the throttle valve opening angle in accordance with signals from the ECM. | |
| Throttle Position Sensor | Detects the throttle valve opening angle and outputs it to the ECM. | ||
| Skid Control Buzzer Assembly | Sounds upon receiving signals from the driving support ECU assembly. | ||
| Speed Sensor | Detects the wheel speed of each of the 4 wheels. | ||
| Accelerator Pedal Sensor Assembly | Detects the accelerator pedal depression angle and transmits it to the ECM. | ||
| Lower Shift Lever Assembly | Transmission Control Switch | ·
Detects the shift lever position and transmits signals to the ECM. ·
Informs the ECM of driver upshift or downshift operations while the shift lever is in S. |
|
| Park/Neutral Position Switch Assembly | Detects the shift lever position and transmits signals to the ECM. | ||
| Steering Sensor | Detects the angle and direction of steering and transmits signals to the skid control ECU and driving support ECU assembly. | ||
| Airbag Sensor Assembly | Yawrate Sensor | Detects the yaw rate of the vehicle and transmits signals to the skid control ECU and driving support ECU assembly. | |
| Stop Light Switch Assembly | Detects brake pedal depression and transmits its signal to the ECM. | ||
| Shift Paddle Switch (Transmission Shift Switch Assembly)* | Informs the ECM of driver upshift or downshift operations. | ||
| VSC OFF Switch | Detects the VSC OFF (TRC OFF) signal and outputs it to the skid control ECU. | ||
SYSTEM CONTROL
The driving support ECU assembly, millimeter wave radar sensor and ECM control this system.
The combination meter assembly informs the driver of the control conditions.
Constant speed control mode is controlled by the ECM, which outputs signals to the throttle control motor.
Vehicle-to-vehicle distance control mode is controlled by the millimeter wave radar sensor assembly and driving support ECU assembly. Thus, the signals are output to the actuators and the ECU while exchanging data as indicated below.
FUNCTION
Function List
The control of the dynamic radar cruise control system varies depending on the mode:
A: Constant Speed Control Mode
B: Vehicle-to-vehicle Distance Control Mode
| Function | Outline | Mode | |
|---|---|---|---|
| A | B | ||
|
○: Available -: Not Available *: Models with shift paddle switch (transmission shift switch assembly) |
|||
| Constant Speed Control | The ECM compares the actual vehicle speed and the set speed and if the vehicle speed is lower than the set speed, it uses the throttle motor to increase the throttle valve opening angle. | ○ | ○ |
| In constant speed control mode, constant speed control is performed by the ECM in the same way as conventional cruise control. | ○ | - | |
| In vehicle-to-vehicle distance control mode, constant speed control is performed by the millimeter wave radar sensor and driving support ECU assembly. | - | ○ | |
| Deceleration Control | Performs throttle control and brake control in order to decelerate the vehicle so that the vehicle-to-vehicle distance between the driver's own vehicle and the vehicle ahead equals the set distance. | - | ○ |
| Follow-up Control | After performing deceleration control, the driver's own vehicle follows the vehicle ahead in order to maintain the proper vehicle-to-vehicle distance in accordance with the vehicle speed. | - | ○ |
| Acceleration Control | Accelerates the vehicle in order to attain the set vehicle speed if the vehicle ahead or the driver's own vehicle has changed lanes. | - | ○ |
| Set Control | When the following conditions are met, and the cruise control switch is pressed to the -SET side and released, the ECM stores the vehicle speed and maintains the vehicle constantly at the current speed.
·
The cruise control system is on. ·
The shift lever is in D or the shift lever is in S with 4th or more shift range selected. ·
The vehicle is traveling at a speed of about 50 km/h (30 mph) or more. |
○ | ○ |
| Low Speed Limit Control | The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 40 km/h (25 mph). The cruise control system cannot be set below that speed. If the vehicle speed drops below that speed while driving using cruise control, speed control by the cruise control system will be canceled automatically. The set vehicle speed is kept in memory. | ○ | ○ |
| COAST Switch Control | While the cruise control switch is held to the - SET side, the vehicle speed and the set vehicle speed change as follows, according to the mode: | ○ | ○ |
·
The vehicle decelerates constantly. ·
The set vehicle speed changes to the speed at which the switch is released. |
○ | - | |
·
The set vehicle speed decreases in increments of 5 km/h or 5 mph. (Example: 103 → 100 → 95 km/h [mph]) ·
The vehicle decelerates rapidly due to ETCS-i. The vehicle will remain at the speed that the vehicle is traveling at when the COAST switch is released. |
- | ○ | |
| Tap Down Control | When the cruise control switch is moved momentarily (approximately 0.6 seconds or less) to the -SET side, the vehicle speed and the set vehicle speed change as follows according to the mode: | ○ | ○ |
·
The vehicle will decelerate in increments of approximately 1 km/h (0.6 mph) for each time the switch is moved. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle is being driven when the switch is pushed. |
○ | - | |
·
The vehicle will decelerate in increments of approximately 1 km/h or 1 mph for each time the switch is moved. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle is being driven when the switch is pushed. |
- | ○ | |
| ACC Switch Control | When the cruise control switch is held to the +RES side, the vehicle speed and the set vehicle speed change as follows according to the mode: | ○ | ○ |
·
The vehicle will accelerate constantly. ·
The set vehicle speed changes to the speed at which the switch is released. |
○ | - | |
·
The set vehicle speed increases in increments of 5 km/h or 5 mph. (Example: 83 →85 →90 km/h [mph]) ·
The vehicle will accelerate to the speed that is set at the time the switch is released. However, only the set vehicle speed will change during follow-up control. |
- | ○ | |
| Tap Up Control | When the cruise control switch is moved momentarily (approximately 0.6 seconds or less) to the +RES side, the vehicle speed and the set vehicle speed change as follows: | ○ | ○ |
·
The vehicle will accelerate in increments of approximately 1 km/h (0.6 mph) for each time the switch is moved. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change. |
○ | - | |
·
The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the switch is moved. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change. |
- | ○ | |
| Shift-down Control | When the vehicle is traveling uphill using cruise control, automatic transmission control may cause the transmission to shift down. During shift-down control, when the end of uphill travel is determined based on the throttle valve angle, the transmission will shift up after a certain period of time. When the transmission shifts down during ACC switch control or RES switch control, the transmission will shift up after ACC switch control or RES switch control ends. | ○ | ○ |
| RES Switch Control | If the vehicle speed is above the low speed limit, the cruise control resumes operation (when the cruise control switch is subsequently moved to the +RES side) to reach the vehicle speed that was set at the time the driver canceled cruise control. | ○ | ○ |
| Even if the vehicle speed dropped below the low speed limit, the set speed can be resumed after the vehicle speed increases above the low speed limit. | ○ | ○ | |
| If the vehicle ahead changes driving lanes during follow-up control, the vehicle speed is gradually increased to the set vehicle speed. At this time, the vehicle speed can be increased promptly by moving the cruise control switch to the +RES side. | - | ○ | |
| Manual Cancel Control | If any of the following signals are sent to the ECM, cruise control speed control operation is canceled accordingly.
·
Shift lever is moved from D or S to any other position. ·
When 1st, 2nd or 3rd shift range is selected manually while in S mode. ·
When 1st, 2nd or 3rd range is selected using a shift paddle switch while shift lever is in D or S to any other position.* ·
Stop light switch on signal (The brake pedal is depressed.) ·
CANCEL switch on signal sent to the ECM (cruise control switch is moved to CANCEL side). ·
Cruise control switch (ON-OFF button) off signal sent to the ECM. |
○ | ○ |
| Automatic Cancel Control | When an automatic cancel signal is sent to the ECM, speed control by the cruise control system is canceled. At this time, the type of warning sent to the driver and the control resumption condition varies according to the cancel signal. | ○ | ○ |
| Mode Switching Control | The following operations switch the mode:
·
The ON-OFF button on the cruise control switch is turned on. (Starts in vehicle-to-vehicle distance control mode.) ·
The cruise control switch is held to the MODE side. (for approximately 1 second or more). If the switch is pushed to any other side before switching modes, turn the cruise control system off, then, perform the steps above again. |
○ | ○ |
| Other Cancelation Conditions | ·
TRC operates for a certain period of time during cruise control driving. ·
VSC operation. ·
VSC OFF (TRC OFF) switch on signal. |
○ | ○ |
| Diagnosis | If a malfunction occurs in the dynamic radar cruise control system during cruise control operation, the ECM cancels cruise control and memorizes information related to the malfunction. | ○ | ○ |
Constant Speed Control in Vehicle-to-vehicle Distance Control
The millimeter wave radar sensor assembly transmits the information about the vehicle ahead to the driving support ECU assembly and also transmits a millimeter wave radar sensor assembly operation signal to the ECM via the driving support ECU assembly. The ECM compares the set vehicle speed and the actual vehicle speed, and performs constant speed control by regulating the throttle in order to attain the set vehicle speed.
Deceleration Control
The driving support ECU assembly calculates the target deceleration rate in accordance with signals from the millimeter wave radar sensor assembly, and transmits a deceleration request signal to the ECM. Upon receiving this signal, the ECM closes the throttle valve in order to cause the vehicle to decelerate.
This control is not performed in the presence of a parked vehicle or object, or below the settable vehicle speed range.
If the driving support ECU assembly determines that further deceleration is necessary, it transmits a brake request signal to the ECM. Upon receiving this signal, the ECM transmits a brake request signal to the skid control ECU. The skid control ECU then controls the brake actuator to apply the brakes.
At this time, if the deceleration rate is higher than a predetermined value, the skid control ECU outputs a stop light illumination request signal to the stop light, in order to warn any vehicles behind.
If the vehicle is not decelerating adequately, the driving support ECU assembly sounds the skid control buzzer assembly to prompt the driver to apply the brakes.
Follow-up Control
After performing deceleration control, the driving support ECU assembly transmits a request signal to the ECM so that the vehicle can follow the vehicle ahead while maintaining the proper vehicle-to-vehicle distance according to the vehicle speed. Upon receiving this signal, the ECM regulates the throttle in order to perform follow-up control.
3 levels (long, middle, and short) of vehicle-to-vehicle distance can be selected by operating the vehicle-to-vehicle distance control switch.
Acceleration Control
If the driving support ECU assembly detects (based on the millimeter wave radar sensor assembly) that either the vehicle ahead or the driver has changed lanes, an acceleration request signal is transmitted to the ECM in order to attain the set vehicle speed. Upon receiving this signal, the ECM regulates the throttle in order to perform acceleration control.
Automatic Cancel Control
If any of the conditions listed below occur while the vehicle is being driven using cruise control, speed control by the cruise control system will be canceled. Then, the following warning items will appear for the driver.
| Situation | Warning | ||
|---|---|---|---|
| Multi-information Display |
|
Buzzer in the combination meter assembly | |
| If either of the conditions listed below occurs, the ECM clears the set vehicle speed and cancels the cruise control system.
·
A malfunction of the vehicle speed signal. ·
An open or short circuit in the stop light switch assembly Speed control by the cruise control system is disabled until the conditions are corrected or the cruise control system is turned off and back on again using the ON-OFF button on the cruise control switch. |
Check Cruise Control System | Illuminates | - |
| If either of the conditions listed below occurs, the ECM clears the set vehicle speed and cancels the cruise control system.
·
Stop light switch assembly input signal is abnormal. ·
Cancel circuit malfunction. Speed control by the cruise control system is disabled until the engine switch is turned on (IG) again. |
Check Cruise Control System | Illuminates | Sounds Once |
| If the condition listed below occurs, the ECM cancels speed control by the cruise control system while retaining the set vehicle speed in its memory.
·
The vehicle speed drops below the low speed limit [approximately 40 km/h (25 mph)]. |
- | Does not illuminate | - |
| If the condition listed below occurs, the ECM clears the set vehicle speed and cancels speed control by the cruise control system.
·
The vehicle speed drops more than 16 km/h (10 mph) below the set vehicle speed. |
- | Does not illuminate | - |
| If the condition listed below occurs, the ECM clears the set vehicle speed and cancels speed control by the cruise control system.
·
A malfunction in the ETCS-i Speed control by the cruise control system is disabled until the condition is corrected or the cruise control system is turned off and back on again using the ON-OFF button on the cruise control switch. |
- | Does not illuminate | - |
| Situation | Warning | ||
|---|---|---|---|
| Multi-information Display |
|
Buzzer in the combination meter assembly | |
| If either of the conditions listed below occurs, the ECM clears the set vehicle speed and cancels speed control by the cruise control system.
·
A malfunction of the vehicle speed signal (SPD). ·
An open or short circuit in the stop light switch assembly Cruise control is prohibited until the normal operating conditions are met or the cruise control system is turned off and back on again using the ON-OFF button on the cruise control switch. |
Check Cruise Control System | Illuminates | Sounds Once |
| If one of the conditions listed below occurs, the ECM clears the set vehicle speed and cancels speed control by the cruise control system.
·
Malfunction of the millimeter wave radar sensor assembly. ·
Misalignment of the axis of the millimeter wave radar sensor assembly. ·
A malfunction in the dynamic radar cruise control system other than those given above. Speed control by the cruise control system is disabled until the engine switch is turned on (IG) again. |
Check Cruise Control System | Illuminates | Sounds Once |
| If either of the conditions listed below occurs, the ECM clears the set vehicle speed and cancels speed control by the cruise control system.
·
Stop light switch assembly input signal is abnormal. ·
Cancel circuit malfunction. Speed control by the cruise control system is disabled until the engine switch is turned on (IG) again. |
Check Cruise Control System | Does not illuminate | Sounds Once |
| If the condition listed below occurs, the ECM clears the set vehicle speed and cancels speed control by the cruise control system.
·
A malfunction is detected in the ETCS-i. Speed control by the cruise control system is disabled until the condition is corrected or the cruise control system is turned off and back on again using the ON-OFF button on the cruise control switch. |
- | Does not illuminate | - |
| If the condition listed below occurs, the ECM cancels speed control by the cruise control system while retaining the set vehicle speed in its memory.
·
The millimeter wave radar sensor assembly is dirty. Cruise control is prohibited until the normal operating conditions are met or the cruise control system is turned off and back on again using the ON-OFF button on the cruise control switch. |
Clean Radar Sensor | Illuminates | Sounds Once |
| If either of the conditions listed below occurs, the ECM cancels speed control by the cruise control system while retaining the set vehicle speed in its memory.
·
The wipers are operating at HI speed. ·
The measurement becomes extremely unstable due to poor weather conditions. Cruise control is prohibited until the normal operating conditions are met or the cruise control system is turned off and back on again using the ON-OFF button on the cruise control switch. |
Cruise Control not available | Illuminates | Sounds Once |
| If the condition listed below occurs, the ECM cancels speed control by the cruise control system while retaining the set vehicle speed in its memory.
·
The vehicle speed drops below the low speed limit (approximately 40 km/h [25 mph]). |
- | Does not illuminate | Sounds Twice |
DIAGNOSIS
If a malfunction occurs in the dynamic radar cruise control system during cruise control operation, the ECM automatically cancels the cruise control, illuminates the master warning light, sounds a buzzer and displays "Check Cruise Control System" on the multi-information display to inform the driver of the malfunction. At this time, the ECM memorizes the malfunction in the form of 5-digit Diagnostic Trouble Codes (DTCs).
The DTC can be read when the Global TechStream (GTS) is connected to the DLC3. For details, refer to the Repair Manual.