FUNCTION OF MAIN COMPONENTS
| Component | Function |
|---|---|
| Clearance Warning ECU Assembly | ·
Judges the approximate distance between the vehicle and an obstacle based on signals from the No. 1 ultrasonic sensors. ·
Sounds the No. 1 clearance warning buzzer. |
| No. 1 Ultrasonic Sensor (2) | Detects the distance between the vehicle and an obstacle. |
| No. 1 Clearance Warning Buzzer | Sounds to inform the driver according to the distance to the obstacle. |
| Back Sonar or Clearance Sonar Switch Assembly | Operating this switch allows the operation of the TOYOTA parking assist-sensor system to be enabled or disabled. |
| Park/Neutral Position Switch Assembly | Sends the shift position signals to the clearance warning ECU assembly. |
| Component | Function |
|---|---|
| Clearance Warning ECU Assembly | ·
Judges the approximate distance between the vehicle and an obstacle based on signals from the No. 1 ultrasonic sensors. Output signals are sent to the combination meter assembly and navigation receiver assembly. ·
Sounds the No. 1 clearance warning buzzer. |
| No. 1 Ultrasonic Sensor (4) | Detects the distance between the vehicle and an obstacle. |
| No. 1 Clearance Warning Buzzer | Sounds to inform the driver according to the distance to the obstacle. |
| Combination Meter Assembly
·
Multi-information Display |
·
Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle. ·
Displays an indication of a malfunction or freezing of a No. 1 ultrasonic sensor to inform the driver. |
| Navigation Receiver Assembly | ·
Displays the location of an obstacle and the approximate distance between the vehicle and the obstacle. ·
Displays an indication of a malfunction or freezing of a No. 1 ultrasonic sensor to inform the driver. ·
The sound volume can be chosen on the setup screen for the TOYOTA parking assist-sensor system. ·
Transmits the setup signal for the TOYOTA parking assist-sensor system to the clearance warning ECU assembly. |
| Back Sonar or Clearance Sonar Switch Assembly | Operating this switch allows the operation of the TOYOTA parking assist-sensor system to be enabled or disabled. |
| Air Conditioning Amplifier Assembly | Sends outside temperature information to the clearance warning ECU assembly to allow distance compensation for the No. 1 ultrasonic sensors. |
| Main Body ECU (Multiplex Network Body ECU) | Sends model destination information (information to indicate the market the vehicle was built for) to the clearance warning ECU assembly. |
| Park/Neutral Position Switch Assembly | Sends the shift position signals to the ECM. |
| ECM | Sends the shift position signals to the clearance warning ECU assembly. |
| Rear Television Camera Assembly | ·
Captures images of the area behind the vehicle. ·
The clearance sonar icon is superimposed on the captured image. Then, the image is sent to the navigation receiver assembly as video signals. |
| Network Gateway ECU | Transmits data between CAN V bus and CAN sub bus 2. |
SYSTEM CONTROL
Detection Area
The detection area of the No. 1 ultrasonic sensor is as shown in the following illustration.
This detection area is applicable when positioning a 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle.
| *a | Approximately 550 mm (21.7 in.) | *b | Approximately 840 mm (33.1 in.) |
| *c | Approximately 500 mm (19.7 in.) | *d | Approximately 600 mm (23.6 in.) |
| *e | Approximately 330 mm (13.0 in.) | *f | Approximately 100 mm (3.9 in.) |
| *g | Approximately 510 mm (20.1 in.) | - | - |
| *a | Approximately 1750 mm (68.9 in.) | *b | Approximately 100 mm (3.9 in.) |
| *c | Approximately 1000 mm (39.4 in.) | *d | Approximately 510 mm (20.1 in.) |
The operating condition of each sensor differs according to its installed position as shown in the table below:
| Installation Position | Operating Condition | Type | |
|---|---|---|---|
| 2-sensor | 4-sensor | ||
|
○: Operates -: Not applicable |
|||
| Front Corner | ·
Engine switch is on (IG). ·
System is activated. ·
Shift lever is in a position other than P or R. ·
Vehicle speed is approximately 10 km/h (6 mph) or less. |
- | ○ |
·
Engine switch is on (IG). ·
System is activated. ·
Shift lever is in R. |
|||
| Rear Corner | ·
Engine switch is on (IG). ·
System is activated. ·
Shift lever is in R. |
- | ○ |
| Rear Center | ·
Engine switch is on (IG). ·
System is activated. ·
Shift lever is in R. |
○ | - |
DIAGNOSIS
If a system malfunction is detected, the clearance warning ECU assembly stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual. (4-sensor type)