Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › from 2016.05
NM19V0EQ _56 Audio / Visual / Telematics _014269 PARK ASSIST / MONITORING _0072871 TOYOTA PARKING ASSIST-SENSOR SYSTEM CO CONTROL F

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  CONTROL  TOYOTA PARKING ASSIST-SENSOR CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with multimedia system

*2: Models with navigation system

*3: Models with parking assist monitor system

Clearance Warning ECU Assembly
·

Judges the approximate distance between the vehicle and an obstacle based on signals from the No. 1 ultrasonic sensors. Output signals are sent to the combination meter assembly and radio and display receiver assembly*1 or navigation receiver assembly*2.

·

Sounds the No. 1 clearance warning buzzer.


No. 1 Ultrasonic Sensor (4) Detects the distance between the vehicle and an obstacle.
No. 1 Clearance Warning Buzzer Sounds to inform the driver according to the distance to the obstacle.
Combination Meter Assembly
·

Multi-information Display


·

Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle.

·

Displays an indication of a malfunction or freezing of a No. 1 ultrasonic sensor to inform the driver.


Radio and Display Receiver Assembly*1
·

Displays the location of an obstacle and the approximate distance between the vehicle and the obstacle.

·

Displays an indication of a malfunction or freezing of a No. 1 ultrasonic sensor to inform the driver.

·

The sound volume can be chosen on the setup screen for the TOYOTA parking assist-sensor system.

·

Transmits the setup signal for the TOYOTA parking assist-sensor system to the clearance warning ECU assembly.


Navigation Receiver Assembly*2
Back Sonar or Clearance Sonar Switch Assembly Operating this switch allows the operation of the TOYOTA parking assist-sensor system to be enabled or disabled.
Air Conditioning Amplifier Assembly Sends outside temperature information to the clearance warning ECU assembly to allow distance compensation for the No. 1 ultrasonic sensors.
Main Body ECU (Multiplex Network Body ECU) Sends model destination information (information to indicate the market the vehicle was built for) to the clearance warning ECU assembly.
Park/Neutral Position Switch Assembly Sends the shift position signals to the ECM.
ECM Sends the shift position signals to the clearance warning ECU assembly.
Rear Television Camera Assembly*3
·

Captures images of the area behind the vehicle.

·

The clearance sonar icon is superimposed on the captured image. Then, the image is sent to the navigation receiver assembly as video signals.


Network Gateway ECU*3 Transmits data between CAN buses.


SYSTEM CONTROL


a.

Detection Area

i.

The detection area of the No. 1 ultrasonic sensor is as shown in the following illustration.


ii.

This detection area is applicable when positioning a 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle.

Y169223C02
1.042,0.5 1.354,0.656 0.313,0.156 10 false *a 5.865,0.74 6.177,0.896 0.313,0.156 10 false *b 1.979,2.792 2.292,2.948 0.313,0.156 10 false *c 5.031,2.781 5.344,2.938 0.313,0.156 10 false *d 1.115,3.74 1.427,3.896 0.313,0.156 10 false *e 1.552,4.448 1.865,4.604 0.313,0.156 10 false *f 5.865,3.719 6.177,3.969 0.313,0.25 10 false *g 4.958,4.469 5.271,4.625 0.313,0.156 10 false *f
*a Approximately 550 mm (21.7 in.) *b Approximately 840 mm (33.1 in.)
*c Approximately 500 mm (19.7 in.) *d Approximately 600 mm (23.6 in.)
*e Approximately 330 mm (13.0 in.) *f Approximately 100 mm (3.9 in.)
*g Approximately 510 mm (20.1 in.) - -




b.

The operating condition of each sensor differs according to its installed position as shown in the table below:

Installation Position Operating Condition
Front Corner
·

Engine switch is on (IG).

·

System is activated.

·

Shift lever is in a position other than P or R.

·

Vehicle speed is approximately 10 km/h (6 mph) or less.


·

Engine switch is on (IG).

·

System is activated.

·

Shift lever is in R.


Rear Corner
·

Engine switch is on (IG).

·

System is activated.

·

Shift lever is in R.






DIAGNOSIS


a.

If a system malfunction is detected, the clearance warning ECU assembly stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.