FUNCTION OF MAIN COMPONENTS
The main components of the engine control system are as follows:
| Component | Outline | Quantity | Function | |
|---|---|---|---|---|
| ECM | 32-bit CPU | 1 | The ECM optimally controls the SFI, ESA and ETCS-i to suit the operating conditions of the engine in accordance with the signals provided by the sensors. | |
| Intake Mass Air Flow Meter Sub-assembly | Mass Air Flow Meter | Hot-wire Type | 1 | This sensor has a built-in hot-wire to directly detect the intake air mass. |
| Intake Air Temperature Sensor | Thermistor Type | 1 | This sensor detects the intake air temperature by means of an internal thermistor (built into the intake mass air flow meter sub-assembly). | |
| E. F. I. Engine Coolant Temperature Sensor | Thermistor Type | 1 | This sensor detects the engine coolant temperature by means of an internal thermistor. | |
| Crank Position Sensor [No. of Rotor Teeth] | Pick-up Coil Type [36 - 2] | 1 | This sensor detects the engine speed and the crank angle. | |
| Camshaft Position Sensor (Intake) [No. of Rotor Teeth] | Magneto- Resistance Element (MRE) Type [3] | 1 | This sensor performs cylinder identification and detects the intake VVT angle. | |
| Camshaft Position Sensor (Exhaust) [No. of Rotor Teeth] | Magneto- Resistance Element (MRE) Type [3] | 1 | This sensor detects the exhaust VVT angle. | |
| Accelerator Pedal Sensor Assembly | Linear (Non-contact) Type | 1 | This sensor detects the amount of pedal effort applied to the accelerator pedal. | |
| Throttle Body with Motor Assembly | Throttle Position Sensor | Linear (Non-contact) Type | 1 | This sensor detects the throttle valve opening angle. |
| Knock Control Sensor | Built-in Piezoelectric Type (Non-resonant Type/Flat Type) | 1 | This sensor detects engine knocking indirectly through the vibration of the cylinder block caused by engine knocking. | |
| Air Fuel Ratio Sensor | Heated Type (Planar Type) | 1 | As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust gas. However, it detects the oxygen concentration in the exhaust gas linearly. | |
| Oxygen Sensor | Heated Type (Cup Type) | 1 | This sensor detects the oxygen concentration in the exhaust gas by measuring the electromotive force which is generated in the sensor itself. | |
| Fuel Injector Assembly | 12-hole Type | 4 | The injector is an electromagnetically-operated nozzle which injects fuel in accordance with signals from the ECM. | |
SYSTEM CONTROL
The engine control system of the 2AR-FE engine has the following features.
| System | Outline |
|---|---|
|
*1: EURO V models *2: Models with smart entry and start system |
|
| Sequential Multiport Fuel Injection (SFI) | ·
This is an L-type SFI system. It directly detects the intake air volume with a hot-wire type intake mass air flow meter sub-assembly. ·
The fuel injection system is a sequential multiport fuel injection system. ·
Fuel injection takes 2 forms: ·
Synchronous injection: always takes place with the same timing in accordance with the basic injection duration and an additional correction based on the signals provided by the sensors. ·
Non-synchronous injection: takes place at the time an injection request based on the signals provided by the sensors is detected, regardless of the crankshaft position. ·
Synchronous injection is further divided into grouped injection during a cold start, and independent injection after the engine is started. |
| Electronic Spark Advance (ESA) | ·
Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking. ·
This system determines the optimal ignition timing in accordance with the signals received from the sensors and sends ignition (IGT) signals to the igniters. |
| Electronic Throttle Control System-intelligent (ETCS-i) | Optimally controls the opening angle of the throttle valve in accordance with the accelerator pedal input and the engine and vehicle operating conditions. |
| Dual Variable Valve Timing-intelligent (Dual VVT-i) | Controls the intake and exhaust camshafts to the optimal valve timing in accordance with engine operating conditions. |
| Acoustic Control Induction System (ACIS) | Switches the intake air passages based on engine speed and throttle valve opening angle to provide high performance in all engine speed ranges. |
| Tumble Control System*1 | Controls to fully close the tumble control valve during cold start and cold running conditions to improve exhaust emissions while the engine is running cold. |
| Fuel Pump Control | ·
Fuel pump operation is controlled by signals from the ECM. ·
The fuel pump is stopped when an SRS airbag is deployed in a frontal or side collision. |
| Air Conditioning Cut-off Control | By controlling the compressor with pulley assembly in accordance with the engine operating conditions, drivability is maintained. |
| Cooling Fan Control | Controls the radiator cooling fan operation in accordance with signals from the ECM based on the E. F. I. engine coolant temperature sensor signal and the operating condition of the air conditioning. |
| Cranking Hold Function (Starter Control)*2 | Once the engine switch is pushed, this control operates the starter until the engine starts. |
| Air Fuel Ratio Sensor and Oxygen Sensor Heater Control | Maintains the temperature of the air fuel ratio sensor or oxygen sensor at an appropriate level to increase the ability of the sensor to accurately detect the concentration of oxygen. |
| Evaporative Emission Control | The ECM controls the purge flow of evaporative emissions (HC) from the canister in accordance with engine operating conditions. |
| Engine Immobiliser | Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key. |
| Fail-safe | When the ECM detects a malfunction, the ECM stops or controls the engine according to the data stored in memory. |
| Diagnosis | When the ECM detects a malfunction, the ECM records the malfunction and information that relates to the fault. |
| Brake Override System | The driving torque is restricted when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection Method, refer to the repair manual) |
FAIL-SAFE
When a malfunction of any of the sensors is detected, there is a possibility of an engine or other malfunction occurring if the ECM were to continue normal control. To prevent such a problem, the fail-safe function of the ECM either relies on the data stored in memory to allow the engine control system to continue operating, or stops the engine if a hazard is anticipated. For details, refer to the Repair Manual.
DIAGNOSIS
When the ECM detects a malfunction, the ECM records information related to the fault. Furthermore, the Malfunction Indicator Lamp (MIL) in the combination meter assembly illuminates or blinks to inform the driver.
The ECM also stores Diagnostic Trouble Codes (DTCs) for malfunctions it has detected. The DTCs can be accessed by using the Global TechStream (GTS).
For details, refer to the Repair Manual.