Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › CYLINDER HEAD
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073933 CYLINDER HEAD A

2AR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A194970
0.109,0.36 0.404,0.523 0.295,0.163 10 SST 0.957,0.654 0.473,0.446 0.473,0.446 1.087,1.105 false

Using SST and a hammer, tap out the valve guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A194985

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard bush bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.


e.

Select a new guide bush (STD or O/S 0.05), and measure its diameter.


f.

Machine the bush bore of the cylinder head to the diameter of the selected guide bush.

Bush Bore Diameter:
Bush Size Specified Condition
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


Standard bush length:

41.3 to 41.7 mm (1.626 to 1.642 in.)



g.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


h.
A194972
0.99,0.813 0.271,0.333 0.271,0.333 1.219,1.323 true 2.448,0.542 2.646,0.719 0.198,0.177 10 false *a 0.042,0.146 0.406,0.313 0.365,0.167 10 false SST
*a Height


Using SST and a hammer, tap in the selected guide bush to the standard protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

14.8 to 15.2 mm (0.582 to 0.598 in.)



i.
A194973

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A285336
1.146,1.167 0.646,0.344 0.646,0.344 1.208,0.646 true 0.385,0.177 0.844,0.375 0.458,0.198 10 false SST

Using SST and a hammer, tap out the valve guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A194975

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard bush bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.


e.

Select a new guide bush (STD or O/S 0.05), and measure its diameter.


f.

Machine the bush bore of the cylinder head to the diameter of the selected guide bush.

Bush Bore Diameter:
Bush Size Specified Condition
STD 10.333 to 10.344 mm (0.4068 in 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


Standard bush length:

46.8 to 47.2 mm (1.843 to 1.858 in.)



g.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


h.
A285337
1.146,1.177 0.615,0.323 0.615,0.323 1.208,0.656 true 2.979,1.313 3.292,1.469 0.313,0.156 10 false *a 0.354,0.156 0.813,0.354 0.458,0.198 10 false SST
*a Height


Using SST and a hammer, tap in the selected guide bush to the standard protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

14.2 to 14.6 mm (0.559 to 0.575 in.)



i.
A285338

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 11115A 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


a.

Remove the ring pins.


b.
A194963
2.229,2.365 3.229,2.542 1,0.177 10 false 6.5 to 7.5 mm

Using a plastic-faced hammer, tap in new ring pins to the cylinder head.

Standard protrusion height:

6.5 to 7.5 mm (0.256 to 0.295 in.)