Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › CYLINDER HEAD
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073933 CYLINDER HEAD A

2AR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL SPARK PLUG TUBE

HINT:

When using a new cylinder head, the spark plug tubes must be replaced.


a.
A194988N08
2.229,0.25 2.125,0.25 2.125,0.25 2.021,0.625 false 2.229,1.604 2.104,1.604 2.104,1.604 1.99,1.813 false 2.26,0.156 2.792,0.313 0.531,0.156 10 false 2.0 mm 2.26,1.521 2.781,1.688 0.521,0.167 10 false 6.0 mm

Apply adhesive onto the shaded area of a new spark plug tube.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


Standard application width:

2.0 mm (0.0787 in.)


NOTICE:
·

Install the spark plug tube within 3 minutes after applying adhesive.

·

Be careful not to deform the spark plug tube.

·

Be careful not to expose the seal to coolant for at least 1 hour after installing it.




b.
A361735C01
2.292,3.708 2.99,3.938 true 3.042,3.875 3.354,4.031 0.313,0.156 10 false *a 2.385,3.073 3.302,3.271 0.917,0.198 10 false 112 mm
*a Cylinder Head Casting Surface


Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

Standard protrusion height:

112 mm (4.41 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



Hide 17159 2.INSTALL CYLINDER HEAD STUD BOLT

a.
A194964N07
1.563,1.781 1.438,1.781 1.438,1.781 1.104,2.219 true 1.969,2.281 1.844,2.281 1.844,2.281 1.563,2.427 false 1.521,3.073 1.365,3.073 1.365,3.073 1.104,2.719 true 1.573,1.698 2.729,1.854 1.156,0.156 10 false 18 mm (0.708 in.) 1.552,2.99 2.792,3.188 1.24,0.198 10 false 13 mm (0.512 in.) 2.01,2.198 3.135,2.385 1.125,0.188 10 false 33 mm (1.299 in.)

Using an E7 "TORX" socket wrench, install the cylinder head stud bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 11117E 3.INSTALL NO. 1 STRAIGHT SCREW PLUG

a.
A194960

Using a 10 mm hexagon wrench, install 3 new gaskets and the 3 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 11117F 4.INSTALL NO. 2 STRAIGHT SCREW PLUG

a.
A194961

Using a 14 mm hexagon wrench, install a new gasket and the straight screw plug.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 13734 5.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head.


Hide 13711E 6.INSTALL VALVE STEM OIL SEAL

a.
A124785C11
1.01,0.813 1.469,0.969 true 2.5,0.813 2.063,0.969 true 0.719,0.063 0.896,0.24 0.177,0.177 10 false *a 2.656,0.052 2.865,0.229 0.208,0.177 10 false *b 1.396,0.344 1.552,0.49 0.156,0.146 10 false *c 1.875,0.885 2.031,1.031 0.156,0.146 10 false *e 1.49,0.885 1.646,1.042 0.156,0.156 10 false *d
*a Intake
*b Exhaust
*c Mark "NOK"
*d Gray
*e Black


Apply a light coat of engine oil to new oil seals.

NOTICE:

Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal onto the exhaust side or installing the exhaust oil seal onto the intake side can cause installation problems later.


HINT:

The intake valve oil seals are gray and the exhaust valve oil seals are black.



b.
A361736C01
1.531,0.198 1.698,0.198 1.698,0.198 2.01,0.688 true 0.906,2.125 1.219,2.281 0.313,0.156 10 false *a 2.188,2.135 2.5,2.292 0.313,0.156 10 false *b 1.25,0.135 1.708,0.333 0.458,0.198 10 false SST
*a CORRECT
*b INCORRECT


Using SST, push in the intake and exhaust valve oil seals.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.



Hide 13711 7.INSTALL INTAKE VALVE

HINT:

Type A and Type B can be distinguished by the shape of the compression spring.

A361727C02
0.292,0.063 3.406,3.76 3.115,3.698 3.792,0.063 6.906,3.76 3.115,3.698 2.354,0.594 3.063,0.594 false 5.823,0.604 6.531,0.604 false 1.969,0.927 2.677,0.927 false 5.375,0.938 6.083,0.938 false 1.958,2.021 2.667,2.021 false 5.406,1.938 6.115,1.938 false 1.844,3.052 2.552,3.052 false 5.292,3.042 6,3.042 false 0.375,0.135 0.708,0.344 0.333,0.208 12 false *A 3.896,0.146 4.396,0.479 0.5,0.333 12 false *B 3.125,0.531 3.438,0.688 0.313,0.156 10 false *1 2.719,0.854 3.031,1.01 0.313,0.156 10 false *2 2.719,1.958 3.031,2.115 0.313,0.156 10 false *3 2.594,2.99 2.906,3.146 0.313,0.156 10 false *4 6.125,0.865 6.438,1.021 0.313,0.156 10 false *2 6.573,0.531 6.885,0.688 0.313,0.156 10 false *1 6.167,1.865 6.479,2.021 0.313,0.156 10 false *3 6.042,2.969 6.354,3.125 0.313,0.156 10 false *4
*A Type A
(Compression Spring Shape: Straight)
*B Type B
(Compression Spring Shape: Tapered)
*1 No. 1 Valve Rocker Arm Sub-assembly *2 Valve Spring Retainer
*3 Compression Spring *4 Valve Lash Adjuster Assembly



a.
A285332C03
2.698,1.563 3.01,1.719 0.313,0.156 10 *a
*a 30 mm (1.18 in.) or more


Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.


b.

Type A

i.

Install the 8 intake valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



ii.
A194956N08
0.087,0.055 0.417,0.205 0.33,0.149 10 SST 1.904,0.075 2.234,0.224 0.33,0.149 10 SST 0.444,0.119 0.573,0.119 0.573,0.119 1.072,0.533 false 2.291,0.153 2.379,0.153 2.379,0.153 2.565,0.223 false

Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.

SST
09202-70020  (09202-00010, 09202-01010, 09202-01020)



c.

Type B:

i.
A337757C01
2.448,0.333 2.667,0.167 2.667,0.167 2.75,0.167 false 2.417,1.333 2.5,1.333 2.5,1.333 2.646,1.042 false 2.771,0.083 3.083,0.24 0.313,0.156 10 false *a 2.25,1.26 2.563,1.417 0.313,0.156 10 false *b
*a Narrow
*b Wide


Install the 8 intake valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



ii.
A337754N01
0.417,0.167 0.583,0.167 0.583,0.167 1.052,0.521 true 2.25,0.167 2.333,0.167 2.333,0.167 2.604,0.229 true 0.104,0.094 0.563,0.292 0.458,0.198 10 false SST 1.958,0.094 2.417,0.292 0.458,0.198 10 false SST

Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.

SST
09202-00021  
09202-70020  (09202-01010, 09202-01020)



d.
A361737

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the retainer.



Hide 13715 8.INSTALL EXHAUST VALVE

HINT:

Type A and Type B can be distinguished by the shape of the compression spring.

A361727C02
0.292,0.063 3.406,3.76 3.115,3.698 3.792,0.063 6.906,3.76 3.115,3.698 2.354,0.594 3.063,0.594 false 5.823,0.604 6.531,0.604 false 1.969,0.927 2.677,0.927 false 5.375,0.938 6.083,0.938 false 1.958,2.021 2.667,2.021 false 5.406,1.938 6.115,1.938 false 1.844,3.052 2.552,3.052 false 5.292,3.042 6,3.042 false 0.375,0.135 0.708,0.344 0.333,0.208 12 false *A 3.896,0.146 4.396,0.479 0.5,0.333 12 false *B 3.125,0.531 3.438,0.688 0.313,0.156 10 false *1 2.719,0.854 3.031,1.01 0.313,0.156 10 false *2 2.719,1.958 3.031,2.115 0.313,0.156 10 false *3 2.594,2.99 2.906,3.146 0.313,0.156 10 false *4 6.125,0.865 6.438,1.021 0.313,0.156 10 false *2 6.573,0.531 6.885,0.688 0.313,0.156 10 false *1 6.167,1.865 6.479,2.021 0.313,0.156 10 false *3 6.042,2.969 6.354,3.125 0.313,0.156 10 false *4
*A Type A
(Compression Spring Shape: Straight)
*B Type B
(Compression Spring Shape: Tapered)
*1 No. 1 Valve Rocker Arm Sub-assembly *2 Valve Spring Retainer
*3 Compression Spring *4 Valve Lash Adjuster Assembly



a.
A285332C03
2.698,1.563 3.01,1.719 0.313,0.156 10 *a
*a 30 mm (1.18 in.) or more


Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.


b.

Type A:

i.

Install the 8 exhaust valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



ii.
A194957N07
2.448,0.094 2.302,0.094 2.302,0.094 2.177,0.698 false 0.938,1.656 0.938,1.531 0.938,1.531 0.75,0.396 false 2.479,0.021 2.792,0.167 0.313,0.146 10 SST 0.75,1.667 1.063,1.813 0.313,0.146 10 SST

Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.

SST
09202-70020  (09202-00010, 09202-01010, 09202-01020)



c.

Type B:

i.
A337758C01
0.875,0.344 0.667,0.167 0.667,0.167 0.583,0.167 false 0.656,1.052 0.333,1.167 0.333,1.167 0.25,1.167 false 0.417,0.094 0.729,0.25 0.313,0.156 10 false *a 0.104,1.083 0.417,1.24 0.313,0.156 10 false *b
*a Narrow
*b Wide


Install the 8 exhaust valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



ii.
A337755N03
2.385,0.479 2.5,0.167 2.5,0.167 2.583,0.167 false 0.729,0.292 0.75,1.833 0.75,1.833 0.833,1.833 true 2.615,0.083 3.073,0.281 0.458,0.198 10 false SST 0.854,1.75 1.313,1.948 0.458,0.198 10 false SST

Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.

SST
09202-00021  
09202-70020  (09202-01010, 09202-01020)



d.
A194981

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the retainer.