Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › CYLINDER BLOCK
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073934 CYLINDER BLOCK A

2AR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the piston or piston ring.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or the threads are damaged, replace it.


a.

Using an E8 and E10 "TORX" socket wrench, install the stud bolts.

A198174C06
5,0.167 4.677,0.458 true 4.677,0.781 4.99,0.979 true 4.99,1.24 4.667,1.448 true 4.688,2.25 5,2.479 true 0.219,1.448 0.396,1.615 0.177,0.167 10 false *b 0.219,0.052 0.396,0.219 0.177,0.167 10 false *a 1.438,1.198 1.552,1.354 0.115,0.156 10 true A 2.5,1.208 2.615,1.365 0.115,0.156 10 true A 3.875,0.063 3.99,0.219 0.115,0.156 10 false A 1.896,2.208 2.042,2.354 0.146,0.146 10 true B 3.875,1.073 4.021,1.219 0.146,0.146 10 false B 5.031,0.083 6.271,0.271 1.24,0.188 10 false 16 mm (0.630 in.) 5.031,0.906 6.521,1.104 1.49,0.198 10 false 12 mm (0.472 in.) 5.031,2.427 6.156,2.594 1.125,0.167 10 false 12 mm (0.472 in.) 5.031,1.146 6.156,1.313 1.125,0.167 10 false 46 mm (1.81 in.) 4.969,1.74 6.094,1.906 1.125,0.167 10 false 67 mm (2.64 in.) 4.969,0.542 6.135,0.74 1.167,0.198 10 false 34 mm (1.34 in.)
*a RH Side *b LH Side


Torque:
for stud bolt A : 6.5 N*m (66 kgf*cm, 58 in.*lbf)
for stud bolt B : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 15709 2.INSTALL NO. 2 OIL NOZZLE SUB-ASSEMBLY

a.
A195789

Using a 5 mm hexagon wrench, install the 4 oil nozzles with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A195788

Using a 5 mm hexagon wrench, install the 2 oil nozzles with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13211 4.INSTALL PISTON

a.

Using a small screwdriver, install a new snap ring at one end of the piston pin hole.


b.

Gradually heat the piston up to 80 to 90°C (176 to 194°F).


c.

Coat the piston, piston pin and connecting rod with engine oil.


d.
A285365C06
0.802,1.219 0.635,0.427 0.635,0.427 0.781,0.427 false 1.073,2.49 0.677,2.042 0.677,2.042 0.531,2.042 false 0.833,0.333 1.146,0.49 0.313,0.156 10 *a 0.365,1.948 0.677,2.104 0.313,0.156 10 *a
*a Front Mark


Align the front marks of the piston and connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the pin comes into contact with the snap ring.

HINT:

The piston and pin are a matched set.



e.
A195811C08
0.729,1.646 0.823,1.646 0.823,1.646 1.24,1.854 true 0.552,1.594 0.729,1.76 0.177,0.167 10 false *1
*1 Service Hole


Using a small screwdriver, install a new snap ring on the other side of the piston pin hole.

HINT:

Be sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.



f.
A195813

Check the fitting condition between the piston and piston pin.

i.

Move the connecting rod back and forth on the piston pin. Check the fitting condition.

If abnormal movement is felt, replace the piston and pin as a set.


ii.

Rotate the piston back and forth on the piston pin. Check the fitting condition.

If abnormal movement is felt, replace the piston and pin as a set.

HINT:

Perform "Inspection After Repair" after replacing the piston.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Hide 13011 5.INSTALL PISTON RING SET

NOTICE:

During installation, use a type A piston ring set for the type A piston, and a type B piston ring set for the type B piston.

A341569C01
2.958,0.979 3.365,0.979 false 2.708,2.167 3.115,2.167 false 5.938,2.156 6.344,2.156 false 6.375,0.938 6.781,0.938 false 0.667,0.115 1.042,0.385 0.375,0.271 12 false *A 4.156,0.094 4.615,0.385 0.458,0.292 12 false *B 3.406,0.906 3.719,1.063 0.313,0.156 10 false *1 3.167,2.094 3.479,2.25 0.313,0.156 10 false *2 6.823,0.865 7.094,1.115 0.271,0.25 10 false *1 6.396,2.083 6.708,2.24 0.313,0.156 10 false *2
*A Type A *B Type B
*1 Piston *2 Oil Ring



a.
A305764C01
1.906,0.385 2.052,0.167 2.052,0.167 2.177,0.167 false 1.813,0.708 2.146,1.01 2.146,1.01 2.313,1.01 true 1.094,3.302 1.875,3.302 1.875,3.302 1.875,3.083 true 1.521,3.094 1.521,3.292 false 2.208,0.083 2.521,0.24 0.313,0.156 10 false *1 2.375,0.927 2.688,1.083 0.313,0.156 10 false *2 1.594,1.792 1.906,1.948 0.313,0.156 10 false *3 0.906,3.208 1.219,3.365 0.313,0.156 10 false *4
*1 Oil Ring
*2 Oil Ring Expander
*3 Coil Joint
*4 Oil Ring End


Type A:

i.

Install the oil ring expander and oil ring by hand.

HINT:

Arrange the oil ring ends and coil joint as shown in the illustration.




b.
A341571C01
2.698,1.094 2.969,1.094 false 2.76,0.813 2.844,0.698 2.844,0.698 2.99,0.698 false 2.74,1.385 2.823,1.49 2.823,1.49 2.969,1.49 false 3.042,0.625 3.354,0.781 0.313,0.156 10 false *1 3.021,1.021 3.333,1.177 0.313,0.156 10 false *2 3.021,1.417 3.333,1.573 0.313,0.156 10 false *3
*1 Upper Oil Ring Side Rail
*2 Oil Ring Expander
*3 Lower Oil Ring Side Rail


Type B:

i.

Install the oil ring expander, upper oil ring side rail and lower oil ring side rail by hand.



c.
A297342C05
1.49,3.146 1.885,3.271 1.885,3.271 2.063,3.271 true 1.49,2.385 2.052,2.219 2.052,2.219 2.198,2.219 true 1.5,2.979 2.052,2.865 2.052,2.865 2.198,2.865 true 1.479,2.552 2.167,2.552 false 0.719,2.677 0.531,2.427 0.531,2.427 0.354,2.427 true 0.719,3.313 0.552,3.094 0.552,3.094 0.375,3.094 true 0.99,4.333 0.99,4.156 false 2.063,4.333 2.063,4.156 false 2.146,0.573 2.49,0.281 2.49,0.281 2.635,0.281 false 2.24,2.125 2.438,2.302 0.198,0.177 10 false *b 0.177,2.323 0.375,2.5 0.198,0.177 10 false *1 0.198,2.99 0.396,3.167 0.198,0.177 10 false *2 2,4.365 2.198,4.542 0.198,0.177 10 false *2 0.917,4.354 1.115,4.531 0.198,0.177 10 false *1 2.229,2.75 2.427,2.927 0.198,0.177 10 false *c 2.094,3.177 2.292,3.354 0.198,0.177 10 false *d 2.208,2.438 2.406,2.615 0.198,0.177 10 false *d 2.688,0.188 2.885,0.365 0.198,0.177 10 false *a
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*a Piston Ring Expander
*b Code Mark (1N or 1NA)
*c Code Mark (2N)
*d Paint Mark
V100135

Upward


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring with the code mark positioned as shown in the illustration.

Piston Ring Mark:
Item Code Mark
No. 1 Compression Ring 1N or 1NA
No. 2 Compression Ring 2N


NOTICE:

Install the compression ring with the code mark facing upward.


HINT:

Perform "Inspection After Repair" after replacing the piston, piston ring.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13471A 6.INSTALL CRANKSHAFT PULLEY KEY

a.

Install the 2 crankshaft pulley keys to the crankshaft.


Hide 11711 7.INSTALL CRANKSHAFT BEARING

a.
A195816C09
1.614,3.832 1.787,3.984 0.173,0.151 10 *a 2.638,3.832 2.812,3.991 0.173,0.159 10 *b
*a CORRECT
*b INCORRECT


Clean the main journal and both surfaces of the bearing.


b.

Install the upper bearing to the cylinder block as shown in the illustration.

NOTICE:
·

Do not apply engine oil to the bearings or their contact surfaces.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the bearing inner surface.

·

If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.




c.
A195817C09
2.323,3.219 1.938,2.573 1.938,2.573 1.792,2.573 false 0.542,3.729 0.75,3.958 0.208,0.229 10 false A 2.219,3.719 2.427,3.948 0.208,0.229 10 false B 1.604,2.51 1.771,2.656 0.167,0.146 10 false *1
*1 Vernier Caliper


Install the lower bearing onto the bearing cap.


d.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and the lower bearing edge.

Standard dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the bearing inner surface.

·

If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.




Hide 11791 8.INSTALL CRANKSHAFT THRUST WASHER

a.
A195787C09
1.406,1.25 1.115,0.385 1.115,0.385 2.01,1.521 true 0.969,0.208 1.146,0.365 0.177,0.156 10 false *1
*1 Oil Groove


Apply engine oil to the thrust washers.


b.

Install the 2 thrust washers onto the No. 3 journal position of the cylinder block with the oil grooves facing outward.


Hide 13411 9.INSTALL CRANKSHAFT

a.
A195784C07
3.063,1.25 1.906,2.031 1.906,2.031 0.75,1.229 false 2.479,1.25 1.906,2.031 1.906,2.031 1.333,1.229 false 1.906,2.01 1.906,1.26 false 1.844,2.021 2,2.177 0.156,0.156 10 false *a
*a Front Mark


Apply engine oil to the upper bearing, and install the crankshaft onto the cylinder block.


b.

Examine the front marks and numbers, and install the bearing caps onto the cylinder block with the front marks as shown in the illustration.

HINT:

The crankshaft bearing cap bolts are tightened in 3 progressive steps.



c.

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


d.

Step 1:

i.
A194889N06
1.583,0.698 1.74,0.802 false 3.125,0.438 3.229,0.583 0.104,0.146 10 false 9 1.688,0.281 1.823,0.458 0.135,0.177 10 true 1 1.688,1.719 1.781,1.896 0.094,0.177 10 true 2 0.76,0.479 0.875,0.625 0.115,0.146 10 true 3 0.833,1.625 0.927,1.781 0.094,0.156 10 true 4 2.573,0.438 2.688,0.583 0.115,0.146 10 true 5 2.594,1.625 2.708,1.781 0.115,0.156 10 true 6 0.292,0.427 0.417,0.583 0.125,0.156 10 false 7 0.302,1.604 0.396,1.75 0.094,0.146 10 false 8 3.094,1.604 3.271,1.75 0.177,0.146 10 false 10

Using several steps, uniformly install and tighten the 10 bearing cap bolts in the sequence shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



e.

Step 2:

i.

Tighten the 10 bearing cap bolts again in the sequence shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

If a crankshaft bearing cap bolt does not meet the specified torque, replace it.



f.

Step 3:

i.
A132155C07
2.01,0.688 2.229,0.229 true 2.25,0.135 2.406,0.281 0.156,0.146 10 false *a 1,0.406 1.375,0.604 0.375,0.198 10 false 90°
*a Paint Mark
V100136

Engine Front


Mark the front of the bearing cap bolts with paint.


ii.

Tighten the 10 bearing cap bolts 90° in the same sequence.


iii.

Check that the paint marks are now at a 90° angle to the front.



g.

Check that the crankshaft turns smoothly.


Hide 13041 10.INSTALL CONNECTING ROD BEARING

a.
A195818C10
0.406,3.063 0.521,3.063 0.521,3.063 0.74,3.438 false 1.729,3.698 1.938,3.927 0.208,0.229 10 false A 2.865,3.698 3.073,3.927 0.208,0.229 10 false B 0.229,2.99 0.406,3.146 0.177,0.156 10 false *1
*1 Vernier Caliper


Clean the bearing contact surface of the connecting rod and cap, and both surfaces of both bearings.


b.

Install the connecting rod bearings to the connecting rods and connecting rod caps.


c.

Using a vernier caliper, measure the distance between the edges of the connecting rod and connecting rod bearing, and the edges of the bearing cap and connecting rod bearing.

Standard dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the bearing inner surface.

·

If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.




Hide 11.INSTALL PISTON WITH CONNECTING ROD

HINT:

Type A and type B can be distinguished by the mark on the piston and the shape of the oil ring.

A341569C01
2.958,0.979 3.365,0.979 false 2.708,2.167 3.115,2.167 false 5.938,2.156 6.344,2.156 false 6.375,0.938 6.781,0.938 false 0.667,0.115 1.042,0.385 0.375,0.271 12 false *A 4.156,0.094 4.615,0.385 0.458,0.292 12 false *B 3.406,0.906 3.719,1.063 0.313,0.156 10 false *1 3.167,2.094 3.479,2.25 0.313,0.156 10 false *2 6.823,0.865 7.094,1.115 0.271,0.25 10 false *1 6.396,2.083 6.708,2.24 0.313,0.156 10 false *2
*A Type A *B Type B
*1 Piston *2 Oil Ring



a.

Apply engine oil to the cylinder walls, pistons, and surfaces of the connecting rod bearings.


b.

Position the piston rings so that the ring ends are as shown in the illustration.

A332508C02
0.5,0.167 0.854,0.406 0.354,0.24 12 false *A 4.021,0.167 4.385,0.417 0.365,0.25 12 false *B 1.021,0.542 1.333,0.698 0.313,0.156 10 false *1 2.615,2.125 2.927,2.281 0.313,0.156 10 false *2 2.625,0.583 2.938,0.74 0.313,0.156 10 false *3 1.031,2.104 1.344,2.26 0.313,0.156 10 false *5 4.344,0.5 4.781,0.688 0.438,0.188 10 false *1, *6 5.927,2.146 6.396,2.333 0.469,0.188 10 false *2, *7 4.469,2.094 4.781,2.25 0.313,0.156 10 false *4 6.063,0.563 6.375,0.719 0.313,0.156 10 false *4
*A for Type A *B for Type B
*1 No. 1 Compression Ring *2 No. 2 Compression Ring
*3 Oil Ring *4 Oil Ring Expander
*5 Oil Ring Expander (Coil Joint) *6 Upper Oil Ring Side Rail
*7 Lower Oil Ring Side Rail - -


HINT:

The type B oil ring expander can be installed with the ring ends in either of the directions shown in the illustration.



c.
A195820C07
1.708,1.385 1.573,1.385 1.573,1.385 1.146,1.01 true 1.75,1.281 1.927,1.458 0.177,0.177 10 false *a
*a Front Mark


Using a hammer handle and piston ring compressor, press a piston with connecting rod into each cylinder with the front mark of the piston facing forward.

NOTICE:

When inserting the piston with connecting rod into the cylinder block, make sure the oil nozzle does not interfere with the connecting rod.


HINT:

The front mark is "2L" or "2S" printed in raised letters.



d.
A194880C13
0.406,1.417 1.365,1.417 1.365,1.417 1.469,0.938 true 0.208,1.344 0.385,1.5 0.177,0.156 10 true *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing in the correct direction.

NOTICE:

Match the numbered connecting rod cap with the connecting rod.



e.
A194881

Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.


f.

Temporarily install the connecting rod bolts.

HINT:

The connecting rod bolts are tightened in 2 progressive steps.



g.

Step 1:

i.

Alternately tighten the connecting rod bolts in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



h.
A101478C43
1.08,0.326 1.435,0.507 0.355,0.182 10 90° 2.418,0.376 2.625,0.558 0.207,0.182 10 *a 2.063,0.725 2.379,0.528 false
*a Paint Mark
V100136

Engine Front


Step 2:

i.

Mark the front of the connecting rod bolts with paint.


ii.

Tighten the bolts 90° as shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



i.

Check that the crankshaft turns smoothly.