Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL PUMP
RM19V0EQ _51 Engine / Hybrid System _014575 2AR-FE FUEL _0073939 FUEL PUMP A

2AR-FE FUEL  FUEL PUMP  DISASSEMBLY  


PROCEDURE

Hide 83320 1.REMOVE FUEL SENDER GAUGE ASSEMBLY

Hide 23221 2.REMOVE FUEL PUMP

a.
A136231

Disconnect the fuel pump harness connectors from the fuel suction plate.


b.
A136234
1.719,1.99 1.073,1.99 false 0.865,1.906 1.042,2.063 0.177,0.156 10 false *1
*1 E-ring


Using needle nose pliers, remove the E-ring.


c.
A211200
1.719,0.552 1.333,0.177 1.333,0.177 1.208,0.177 false 1.031,0.073 1.219,0.24 0.188,0.167 10 *1
*1 Tube


Disengage the 4 claws of the No. 1 fuel suction support and remove the lower fuel tank case sub-assembly from the fuel suction plate with the fuel filter.


d.

Remove the spring from the fuel suction plate.

NOTICE:

Do not do anything which may separate the fuel tube from either the fuel suction plate or fuel filter assembly, such as applying excessive force to the tube.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM>PRECAUTION



e.
A255954

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the No. 1 fuel suction support.


f.
A296957
2.177,0.427 2.583,0.427 false 3.01,1.896 3.01,1.542 false 2.625,0.365 2.938,0.521 0.313,0.156 10 *1 2.938,1.958 3.25,2.115 0.313,0.156 10 *2
*1 Fuel Filter
*2 Suction Filter


Using a screwdriver with its tip wrapped in protective tape, disengage the 5 claws, and remove the fuel pump from the fuel filter.

NOTICE:
·

Do not damage the fuel filter.

·

Do not remove the suction filter.

·

Do not use either the fuel pump or the suction filter if the suction filter is removed from the fuel pump.




g.
A192528

Remove the fuel pump harness connector.


h.
A192533
0.917,4.01 0.99,4.146 0.99,4.146 1.229,4.146 false 2.229,0.667 2.427,0.469 2.427,0.469 2.594,0.469 false 2.229,0.813 2.625,0.813 false 2.656,0.385 2.854,0.594 0.198,0.208 10 *1 2.646,0.719 2.833,1.073 0.188,0.354 10 *2 1.948,2.24 2.125,2.469 0.177,0.229 10 *a 1.906,1.656 2.083,1.813 0.177,0.156 10 *a 1.281,4.052 1.469,4.24 0.188,0.188 10 *1
*1 O-ring
*2 Fuel Pump Spacer
*a 5.0 mm (0.197 in.)


Remove the O-ring and fuel pump spacer from the fuel pump.

NOTICE:

Be careful not to damage the sealing surface.


HINT:

If the O-ring still remains in the fuel filter, remove it using a wire tip (1 mm diameter) that is formed as shown in the illustration.