Home › Engine / Hybrid System › 2AR-FE EMISSION CONTROL › CANISTER
RM19V0EQ _51 Engine / Hybrid System _014576 2AR-FE EMISSION CONTROL _0073943 CANISTER G

2AR-FE EMISSION CONTROL  CANISTER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 77740 1.INSPECT CHARCOAL CANISTER ASSEMBLY

a.

Visually check the charcoal canister.

i.

Visually check the charcoal canister for cracks or damage.

HINT:

If cracks or damage are found, replace the charcoal canister assembly.




b.

Check charcoal canister operation under positive pressure.

i.
A255917
0.604,0.885 0.719,0.885 0.719,0.885 1.365,1.24 true 0.885,2.542 0.885,2.823 false 0.448,0.813 0.615,0.99 0.167,0.177 10 true *1 0.802,2.844 1.104,3.083 0.302,0.24 10 false *2 0.313,2.167 0.542,2.385 0.229,0.219 10 true *a
*1 Vent Line Hose
*2 Test Hose
*a Air


Disconnect the vent line hose from the charcoal canister assembly. Close the vent line hose using a hose plug or a similar part.


ii.

Connect a test hose to the charcoal canister assembly.


iii.

Blow 5 kPa (0.1 kgf/cm2, 0.7 psi) of air into the hose.

Standard:

Air can be blown through the canister.


HINT:

If the standard is not as specified, replace the charcoal canister assembly.




c.

Check charcoal canister operation under vacuum.

i.

Disconnect the vent line hose from the charcoal canister assembly. Close the vent line hose using a hose plug or a similar part.


ii.

Connect a test hose to the charcoal canister assembly.


iii.

Connect a vacuum pump to the test hose.


iv.
A255918
0.625,0.51 0.729,0.51 0.729,0.51 1.344,0.802 true 1.417,2.323 1.417,2.917 false 0.458,0.448 0.625,0.635 0.167,0.188 10 true *1 1.333,2.979 1.615,3.24 0.281,0.26 10 false *2
*1 Vent Line Hose
*2 Test Hose


Using the vacuum pump, apply vacuum and check the indicator.

Standard:

The vacuum pump indicator does not move from its initial position.


HINT:
·

The indicator may move when applying vacuum. If the indicator quickly returns to its initial position, the charcoal canister is operating normally.

·

If the standard is not as specified, replace the charcoal canister assembly.





d.

Check for clogs in the air filter (when not using the intelligent tester).

i.

Disconnect the vent line hose from the charcoal canister assembly. Close the vent line hose using a hose plug or a similar part.


ii.

Connect a test hose to the charcoal canister assembly.


iii.

Connect a vacuum pump to the test hose.


iv.

Start the engine.


v.

Warm up the engine.


vi.

After warm-up, idle the engine for 15 minutes and check the vacuum pump indicator.

Standard:

The vacuum pump indicator does not move from its initial position.


HINT:

The indicator may move when the purge VSV opens to vacuum. If the indicator quickly returns to its initial position, the charcoal canister is operating normally.




e.

Check for clogs in the air filter (when using the intelligent tester).

HINT:

When performing an Active Test of the purge VSV using the intelligent tester, it is not necessary to warm-up and idle the engine for 15 minutes.


i.

Disconnect the vent line hose from the charcoal canister assembly. Close the vent line hose using a hose plug or a similar part.


ii.

Connect a test hose to the charcoal canister assembly.


iii.

Connect a vacuum pump to the test hose.


iv.

Connect the intelligent tester to the DLC3.


v.

Start the engine.


vi.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

vii.

Perform the Active Test with the engine idling.

Standard:

The vacuum pump indicator does not move from its initial position.


HINT:

The indicator may move when the purge VSV opens to vacuum. If the indicator quickly returns to its initial position, the charcoal canister is operating normally.