Home › Engine / Hybrid System › 2AR-FE INTAKE / EXHAUST › EXHAUST PIPE
RM19V0EQ _51 Engine / Hybrid System _014577 2AR-FE INTAKE / EXHAUST _0073951 EXHAUST PIPE A

2AR-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum 40.5 mm (1.60 in.)

HINT:

If the free length is less than minimum, replace the compression spring.



b.

Fully insert a new gasket to the exhaust manifold converter sub-assembly.


c.
A181728C35
1.667,0.146 1.823,0.146 1.823,0.146 1.833,1.125 false 2.042,2.302 1.188,2.615 1.188,2.615 0.99,2.615 false 2.521,1.385 2.833,1.563 2.833,1.563 2.833,1.802 false 1.448,0.083 1.635,0.271 0.188,0.188 10 false *1 0.76,2.531 0.927,2.719 0.167,0.188 10 false *2 2.792,1.865 3.031,2.073 0.24,0.208 10 false *3
*1 Exhaust Manifold Converter Sub-assembly
*2 Gasket
*3 Wooden Block


Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.

Connect the front exhaust pipe assembly to the exhaust pipe support.


Hide 17420 2.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the front exhaust pipe assembly.


b.

Connect the center exhaust pipe assembly to the exhaust pipe support.


c.

Install the center exhaust pipe assembly with the 2 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17430 3.INSTALL TAIL EXHAUST PIPE ASSEMBLY (for Single Type)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum 38.5 mm (1.52 in.)

HINT:

If the free length is less than minimum, replace the compression spring.



b.

Fully insert a new gasket to the center exhaust pipe assembly.


c.
A181728C35
1.667,0.146 1.823,0.146 1.823,0.146 1.833,1.125 false 2.042,2.302 1.188,2.615 1.188,2.615 0.99,2.615 false 2.521,1.385 2.833,1.563 2.833,1.563 2.833,1.802 false 1.448,0.083 1.635,0.271 0.188,0.188 10 false *1 0.76,2.531 0.927,2.719 0.167,0.188 10 false *2 2.792,1.865 3.031,2.073 0.24,0.208 10 false *3
*1 Center Exhaust Pipe Assembly
*2 Gasket
*3 Wooden Block


Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the center exhaust pipe assembly.

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the tail exhaust pipe assembly to the 3 exhaust pipe supports.


e.

Install the tail exhaust pipe assembly with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17430 4.REMOVE TAIL EXHAUST PIPE ASSEMBLY (for Dual Type)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum 38.5 mm (1.52 in.)

HINT:

If the free length is less than minimum, replace the compression spring.



b.

Fully insert 2 new gaskets to the center exhaust pipe assembly.


c.
A181728C35
1.667,0.146 1.823,0.146 1.823,0.146 1.833,1.125 false 2.042,2.302 1.188,2.615 1.188,2.615 0.99,2.615 false 2.521,1.385 2.833,1.563 2.833,1.563 2.833,1.802 false 1.448,0.083 1.635,0.271 0.188,0.188 10 false *1 0.76,2.531 0.927,2.719 0.167,0.188 10 false *2 2.792,1.865 3.031,2.073 0.24,0.208 10 false *3
*1 Center Exhaust Pipe Assembly
*2 Gasket
*3 Wooden Block


Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the center exhaust pipe assembly.

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the 2 tail exhaust pipe assemblies to the 5 exhaust pipe supports.


e.

Install the 2 tail exhaust pipe assemblies with the 2 bolts, 2 compression springs and 2 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 6.INSPECT FOR EXHAUST GAS LEAK