Home › Engine / Hybrid System › 2AR-FE STARTING › STARTER
RM19V0EQ _51 Engine / Hybrid System _014580 2AR-FE STARTING _0073966 STARTER G

2AR-FE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to avoid burning out the coil.


a.

Perform a pull-in test.

i.

Disconnect the lead wire from terminal C.


ii.
A197192
2.365,1.26 2.5,2.208 2.5,2.208 2.5,2.323 false 2.146,1.281 1.656,2 1.656,2 1.656,2.125 false 1.167,1.719 1.167,2.135 false 2.427,2.344 2.594,2.531 0.167,0.188 10 false *2 1.594,2.156 1.792,2.344 0.198,0.188 10 false *1 1.083,2.146 1.281,2.333 0.198,0.188 10 false *3
*1 Terminal 50
*2 Terminal C
*3 Body


Connect the battery to the magnet starter switch as shown in the illustration. Check that the clutch pinion gear extends.

If the clutch pinion gear does not move, replace the magnet starter switch assembly.



b.
A197193
2.385,1.271 2.552,2.042 2.552,2.042 2.552,2.146 false 1.167,1.719 1.167,2.229 false 2.146,1.302 2.01,2.073 2.01,2.073 2.01,2.156 false 2.5,2.219 2.688,2.385 0.188,0.167 10 false *2 1.938,2.208 2.125,2.375 0.188,0.167 10 false *1 1.104,2.271 1.26,2.438 0.156,0.167 10 false *3
*1 Disconnect
*2 Terminal C
*3 Body


Perform a hold-in test.

i.

Maintain the battery connections of the pull-in test above, but disconnect the negative (-) lead from terminal C. Check that the pinion gear remains extended.

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



c.
A197194
2.385,1.281 2.833,2.188 2.833,2.188 2.833,2.25 false 2.146,1.333 1.969,2.083 1.969,2.083 1.969,2.167 false 1.177,1.75 1.104,2.042 1.104,2.042 1.104,2.104 false 2.76,2.281 2.917,2.417 0.156,0.135 10 false *2 1.885,2.188 2.042,2.323 0.156,0.135 10 false *1 1.021,2.125 1.177,2.26 0.156,0.135 10 false *3
*1 Disconnect
*2 Terminal C
*3 Body


Check the clutch pinion gear return.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the repair service starter kit.



d.
A197195
2.385,1.604 2.167,0.969 2.167,0.969 2.083,0.969 false 2.125,1.906 1.51,2.688 1.51,2.688 1.51,2.781 false 1.896,0.865 2.052,1.031 0.156,0.167 10 false *1 1.438,2.813 1.625,2.979 0.188,0.167 10 false *2
*1 Terminal 30
*2 Terminal 50


Perform a no-load performance test.

i.

Connect the lead wire to terminal C with the nut. Make sure that the lead is not grounded.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Clamp the starter in a vise.


iii.

Connect the battery and an ammeter to the starter as shown in the illustration.


iv.

Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

Standard current:

90 A or less at 11.5 V


If the result is not as specified, repair or replace the starter assembly.



Hide 2.INSPECT STARTER CLUTCH

a.

Check the starter clutch.

i.
A197200
2.083,0.844 2.281,1.01 0.198,0.167 10 false *a 1.448,1.906 1.719,2.135 0.271,0.229 10 false *b
*a Lock
*b Free


Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.

If necessary, replace the repair service starter kit.



Hide 28150 3.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A197181

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If necessary, replace the magnet starter switch assembly.



b.
A197182
2.188,1.375 2.542,1.375 false 1.844,1.417 1.313,1.719 1.313,1.719 1.198,1.719 false 2.583,1.302 2.781,1.469 0.198,0.167 10 false *2 0.99,1.656 1.177,1.823 0.188,0.167 10 false *1
*1 Terminal 50
*2 Terminal C


Inspect the pull-in coil.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



c.
A197183
1.938,1.5 1.406,1.802 1.406,1.802 1.292,1.802 false 1.125,0.458 1.333,0.219 1.333,0.219 1.448,0.219 false 1.51,0.146 1.771,0.365 0.26,0.219 10 false *2 1.115,1.729 1.385,1.958 0.271,0.229 10 false *1
*1 Terminal 50
*2 Body


Check if the hold-in coil.

i.

Measure the resistance between terminal 50 and the switch body.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Switch bod Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.



Hide 28160 4.INSPECT STARTER ARMATURE ASSEMBLY

a.
A058372
1.448,1.146 2.552,1.781 2.552,1.781 1.354,1.271 true 2.594,1.729 2.771,2.052 0.177,0.323 10 false *1
*1 Segment


Inspect the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



b.
A058373
1.313,1.177 1.031,1.281 false 1.854,1.042 2.542,1.573 2.542,1.573 2.667,1.573 true 0.854,1.198 1.01,1.396 0.156,0.198 10 false *1 2.75,1.5 3,1.719 0.25,0.219 10 false *2
*1 Commutator
*2 Armature coil core


Inspect the commutator for a short circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Commutator - Armature coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



c.

Check the surface of the commutator for dirt and burns.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.


d.
A194765
2.771,0.846 2.966,1.028 0.196,0.182 10 *a
*a Length


Using a vernier caliper, measure the commutator length.

Standard length:

3.1 to 3.8 mm (0.122 to 0.149 in.)


If the length is more than the maximum, replace the starter armature assembly.


Hide 28130 5.INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A194766
0.24,0.885 0.438,1.063 0.198,0.177 10 false *a
*a Length


Using a vernier caliper, measure the brush length.

Standard length:

4.0 to 9.0 mm (0.158 to 0.354 in.)


If the length is less than the minimum, replace the starter commutator end frame assembly.


b.
A079766
1.438,0.885 1,1.292 1,1.292 1.656,1.25 true 1.792,0.688 2.406,0.292 2.406,0.292 2,0.979 true 2.427,0.198 2.635,0.531 0.208,0.333 10 (+) 0.781,1.198 0.948,1.531 0.167,0.333 10 (-)

Inspect the insulation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush - Negative (-) brush Always 10 kΩ or higher


If the result is not as specified, repair or replace the starter commutator end frame assembly.