Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE FLUID
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073974 AUTOMATIC TRANSAXLE FLUID N

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE FLUID  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

Precautions and work description

·

The U760E automatic transaxle does not have an oil filler tube and oil dipstick. When adding fluid, add fluid through the refill hole on the transaxle case. The fluid level can be adjusted by draining excess fluid (allowing excess fluid to overflow) through the No. 1 transmission oil filler tube of the oil pan.

·

Before adjusting the fluid level, add the specified amount of fluid when the engine is cold and warm up the engine to circulate the fluid in the transaxle. Ensure that the fluid temperature is as specified and the engine is idling.

·

The U760E automatic transaxle requires Toyota Genuine ATF WS.

·

The adjustment should be performed according to the procedures and notes.



HINT:

"Overflow" indicates the condition under which fluid comes out of the overflow plug hole.


C170581
2.729,2.51 2.729,2.396 2.729,2.396 1.958,2.073 false 6.094,2.563 6.094,2.469 6.094,2.469 5.698,2.281 false 1.26,3.385 4.323,3.573 3.063,0.188 10 3. ADJUST FLUID TEMPERATURE 0.271,6.042 2.219,6.198 1.948,0.156 10 4. ADJUST FLUID LEVEL 0.031,0.021 1.51,0.219 1.479,0.198 10 Fluid Filling Procedure: 0.396,0.375 2.354,0.542 1.958,0.167 10 1. PERFORM INITIAL FILLING 4.052,0.375 6.646,0.563 2.594,0.188 10 2. ADD SPECIFIED AMOUNT OF FLUID 0.396,0.646 2.365,0.958 1.969,0.313 10 Add fluid to the specified level. 4.052,0.646 6.719,0.958 2.667,0.313 10 Add the correct amount of fluid specified for the operation that was performed. 5.656,2.573 6.583,2.896 0.927,0.323 10 Overflow Plug 3.792,7.885 5.604,8.24 1.813,0.354 10 Add fluid until fluid comes out of the overflow plug hole. 0.031,2.396 1.875,3.281 1.844,0.885 10 Add fluid until fluid comes out of the overflow plug hole. 0.063,7.896 2.073,8.375 2.01,0.479 10 Keep the overflow plug open until the fluid only drips out. 0.24,6.333 2.583,6.792 2.344,0.458 10 Drain excess fluid at the specified fluid temperature. 4.188,6.323 6.667,6.656 2.479,0.333 10 If no fluid comes out, add fluid until fluid comes out of the overflow plug hole. 1.135,3.667 6.927,4.094 5.792,0.427 10 Start the engine to circulate the fluid. Activate fluid temperature detection mode and engine idle speed control mode, and adjust the fluid temperature to the specified level. 2.115,2.51 3.333,2.833 1.219,0.323 10 No. 1 Transmission Oil Filler Tube 6.458,1.594 7.073,2.521 0.615,0.927 10 Specified Amount of Fluid

HINT:

The adjustment should be performed according to the procedures referenced in the work flow below.


C197806
0.073,0.052 1.469,0.365 1.396,0.313 10 Work Flow: 3.354,0.208 4.01,0.573 0.656,0.365 10 START 1.365,1.417 2.667,1.823 1.302,0.406 10 Perform initial filling 1.052,3.51 6.198,3.917 5.146,0.406 10 Activate fluid temperature detection mode and engine idle speed control mode 3.948,1.417 6.531,1.823 2.583,0.406 10 Not necessary to perform initial filling 2.688,2.365 5.083,2.771 2.396,0.406 10 Add specified amount of fluid 3.063,5.729 4.188,6.135 1.125,0.406 10 Drain excess fluid 3.021,7.625 4.26,8.031 1.24,0.406 10 Finish up operation 3.438,8.385 3.781,8.74 0.344,0.354 10 END 5.823,6.875 6.479,7.281 0.656,0.406 10 Add fluid 3.354,6.865 3.958,7.271 0.604,0.406 10 Overflow 2.49,5.052 4.75,5.458 2.26,0.406 10 Fluid level adjustment temperature 5.427,4.583 6.896,5.063 1.469,0.479 10 Above fluid level adjustment temperature 5.479,6.177 6.854,6.542 1.375,0.365 10 No fluid comes out 0.188,7.51 2.833,7.833 2.646,0.323 10 Step 5. REBUILD WORK 0.188,0.677 2.833,1 2.646,0.323 10 Step 1. PERFORM INITIAL FILLING 0.188,5.583 2.354,5.906 2.167,0.323 10 Step 4. ADJUST FLUID LEVEL 0.188,3.135 3.063,3.458 2.875,0.323 10 Step 3. ADJUST FLUID TEMPERATURE 0.188,2.25 2.344,2.583 2.156,0.333 10 Step 2. ADD SPECIFIED AMOUNT OF FLUID 2.854,4.25 4.469,4.458 1.615,0.208 10 Idling (Warm up the fluid)

PROCEDURE

Hide 1. PREPARATION WORK

NOTICE:

If the transaxle is hot (ATF temperature is high), wait until the fluid temperature becomes the same as the ambient temperature before starting the following procedure. [Recommended ATF temperature: around 20°C (68°F)]


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up.



b.

Remove the front wheel opening extension pad LH, engine under cover LH and front fender apron seal LH.


Hide 2. PERFORM INITIAL FILLING

NOTICE:

After performing either of the following operations, it is not necessary to perform the initial filling procedure. Proceed to the "Add Specified Amount of Fluid" procedure.


Operations that do not require initial filling
·

Oil cooler tube or oil cooler hose removal/installation


·

Repair of oil seeping or oozing



a.
C201682

Remove the refill plug and gasket from the automatic transaxle assembly.


b.
C201683
1.506,2.847 1.656,2.997 0.15,0.15 10 *1 1.506,3.683 1.667,3.835 0.161,0.152 10 *3 1.506,3.333 1.666,3.489 0.16,0.155 10 *2 1.468,2.927 0.981,2.927 false 1.468,3.42 1.009,3.42 false 1.468,3.763 0.956,3.763 false
*1 No. 1 Transmission Oil Filler Tube
*2 Overflow Plug
*3 Hexagon Socket Wrench


Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle assembly.

NOTICE:
·

If ATF comes out after removing the overflow plug, wait until the fluid flow slows and only drips come out.

·

If ATF comes out, it is not necessary to perform the initial filling procedure. After checking the tightening torque of the No. 1 transmission oil filler tube, temporarily tighten the overflow plug.




c.
C201684
1.208,2.677 0.833,2.677 false 0.583,3.969 0.396,3.969 0.396,3.969 0.688,3.167 false 1.208,3.219 0.833,3.219 false 1.219,2.594 1.375,2.76 0.156,0.167 10 false *1 1.219,3.135 1.385,3.302 0.167,0.167 10 false *2 0.646,3.885 0.979,4.177 0.333,0.292 10 false *a
*1 No. 1 Transmission Oil Filler Tube
*2 Hexagon Socket Wrench
*a Overflow Plug Hole


Using a 6 mm hexagon socket wrench, check that the No. 1 transmission oil filler tube is tightened to the specified torque.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)

NOTICE:

If the No. 1 transmission oil filler tube is not tightened to the specified torque, the amount of fluid cannot be precisely adjusted.


HINT:

To check the torque of the No. 1 transmission oil filler tube, insert the 6 mm hexagon socket wrench into the overflow plug hole.



d.

Perform initial filling.

i.
C201685

Fill the transaxle through the refill hole until fluid begins to trickle out of the overflow plug hole.

NOTICE:

Use Toyota Genuine ATF WS.




e.
C201686

Wait until the fluid flow slows and only drips come out.


f.
C201683
1.506,2.847 1.656,2.997 0.15,0.15 10 *1 1.506,3.683 1.667,3.835 0.161,0.152 10 *3 1.506,3.333 1.666,3.489 0.16,0.155 10 *2 1.468,2.927 0.981,2.927 false 1.468,3.42 1.009,3.42 false 1.468,3.763 0.956,3.763 false
*1 No. 1 Transmission Oil Filler Tube
*2 Overflow Plug
*3 Hexagon Socket Wrench


Using a 6 mm hexagon socket wrench, temporarily install the gasket and the overflow plug.

HINT:

Reuse the old gasket. The overflow plug will be removed again to adjust the fluid level.



Hide 3.ADD SPECIFIED AMOUNT OF FLUID

a.

Fill the transaxle with the correct amount of fluid as listed in the table below.

NOTICE:

Refill amount differs depending on the operation that was performed.


Reference Capacity:
Related Procedure Fill Volume
Transaxle replacement (with a new torque converter) 5.1 liters (5.4 US qts, 4.5 Imp. qts)
Transaxle replacement (when reusing the torque converter) 3.5 liters (3.7 US qts, 3.1 Imp. qts)
Torque converter removal/installation 3.4 liters (3.6 US qts, 3.0 Imp. qts)
Transmission valve body removal/installation 3.2 liters (3.4 US qts, 2.8 Imp. qts)
Oil pan removal/installation 2.7 liters (2.9 US qts, 2.4 Imp. qts)
Drive shaft removal/installation 2.7 liters (2.9 US qts, 2.4 Imp. qts)
Transaxle case oil seal removal/installation 2.7 liters (2.9 US qts, 2.4 Imp. qts)
Oil cooler tube or oil cooler hose removal/installation 0.5 liters (0.5 US qts, 0.4 Imp. qts)
Repair of oil seeping or oozing 0.5 liters (0.5 US qts, 0.4 Imp. qts)



b.
C201682

Temporarily install the refill plug to avoid fluid spillage.

HINT:

Reuse the old gasket. The refill plug will be removed again to adjust the fluid level.



c.

Lower the vehicle.


Hide 4.ADJUST FLUID TEMPERATURE (for Using the intelligent tester)

HINT:

The actual ATF temperature can be checked on the Data List using the intelligent tester.


a.

Connect the intelligent tester to the DLC3 with the ignition switch off.


b.

Turn the ignition switch to ON and turn the intelligent tester on.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.



c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

d.

Select the Data List menu: A/T Oil Temperature 1


e.

Select the Active Test menu: Connect the TC and TE1 / ON


f.

Check the ATF temperature.

NOTICE:
·

If the fluid temperature is below 45°C (113°F), proceed to the next step. [Recommended ATF temperature: 35°C (95°F) or less]

·

If the fluid temperature is 45°C (113°F) or more, turn the ignition switch off and wait until the fluid temperature drops below 45°C (113°F).




g.

Depress and hold the brake pedal.


h.

Start the engine.


i.

Slowly move the shift lever from P to D, then back to P (keep the shift lever in each position for approximately 3 seconds).

HINT:

Slowly move the shift lever to circulate the fluid through each part of the automatic transaxle assembly.



j.
C251106

While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter fluid temperature detection mode.



k.

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the first step and perform the procedure again.




l.

Move the shift lever from N to P.


m.

Release the brake pedal.


n.

Select the Active Test menu: Connect the TC and TE1 / OFF

NOTICE:

Be sure that terminals TC and TE1 are off. If the terminals are on, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting terminals TC and TE1 activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the fluid temperature becomes 35°C (95°F) or more and the engine speed is maintained at approximately 800 rpm.

·

Even after terminals TC and TE1 are disconnected, fluid temperature detection mode is active until the ignition switch is turned off.




o.
C247466
0.51,1.188 0.781,1.448 0.271,0.26 10 false *a 2.281,0.188 2.552,0.438 0.271,0.25 10 false *c 1.156,0.198 1.427,0.458 0.271,0.26 10 false *b
*a Turned Off
*b Turned On
*c Blinking


Warm up the engine with the engine idling until the fluid temperature reaches the fluid level adjustment temperature [35 to 45°C (95 to 113°F)].

Below Fluid Level Adjustment Temperature Fluid Level Adjustment Temperature Above Fluid Level Adjustment Temperature
35°C or less (95°F or less) 35 to 45°C (95 to 113°F) 45°C or more (113°F or more)
Shift Indicator (D)
Turned off
Shift Indicator (D)
Turned on
Shift Indicator (D)
Blinking

NOTICE:
·

If the fluid temperature is within the fluid level adjustment temperature range, immediately proceed to the "Adjust Fluid Level" procedure.

·

If the fluid temperature is 45°C (113°F) or more, stop the engine and wait until the fluid temperature drops to 35°C (95°F) or less. Then perform the "Adjust Fluid Temperature" procedure again from the beginning.



HINT:

In fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.



Hide 5.ADJUST FLUID TEMPERATURE (for not Using the intelligent tester)

a.
C101492
1.948,1.479 1.948,1.854 false 1.688,0.74 1.177,0.354 false 0.948,0.74 1.094,0.917 0.146,0.177 10 false 1 1.177,0.74 1.344,0.938 0.167,0.198 10 false 2 2.115,0.74 2.281,0.927 0.167,0.188 10 false 6 2.552,1.26 2.76,1.448 0.208,0.188 10 false 16 1.896,0.74 2.063,0.927 0.167,0.188 10 false 5 1.646,0.74 1.813,0.927 0.167,0.188 10 false 4 1.417,0.74 1.583,0.927 0.167,0.188 10 false 3 0.948,1.26 1.146,1.458 0.198,0.198 10 false 9 1.385,1.26 1.583,1.458 0.198,0.198 10 false 11 2.365,0.74 2.563,0.938 0.198,0.198 10 false 7 2.583,0.74 2.781,0.938 0.198,0.198 10 false 8 1.146,1.26 1.344,1.458 0.198,0.198 10 false 10 1.604,1.26 1.844,1.469 0.24,0.208 10 false 12 1.844,1.26 2.031,1.448 0.188,0.188 10 false 13 2.083,1.26 2.271,1.448 0.188,0.188 10 false 14 2.313,1.26 2.531,1.438 0.219,0.177 10 false 15 0.917,0.219 1.344,0.5 0.427,0.281 10 false CG 0.156,0.146 0.729,0.5 0.573,0.354 10 false *1 1.844,1.875 2.083,2.042 0.24,0.167 10 false TC
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.

SST
09843-18040  


b.

Depress and hold the brake pedal.


c.

Start the engine.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.


HINT:

The indicator lights on the combination meter blink to indicate the DTC output when terminals TC and CG are connected.



d.

Slowly move the shift lever from P to D, then back to P.

HINT:

Slowly move the shift lever to circulate the fluid through each part of the automatic transaxle assembly.



e.
C251106

While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter fluid temperature detection mode.



f.

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the first step and perform the procedure again.




g.

Move the shift lever from N to P.


h.

Release the brake pedal.


i.

Remove SST from terminals 13 (TC) and 4 (CG).

NOTICE:

Be sure that terminals TC and CG are not connected. If the terminals are connected, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting terminals TC and CG activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the fluid temperature becomes 35°C (95°F) or more and the engine speed is maintained at approximately 800 rpm.

·

Even after terminals TC and CG are disconnected, fluid temperature detection mode is active until the ignition switch is turned off.




j.
C247466
0.51,1.188 0.781,1.448 0.271,0.26 10 false *a 2.281,0.188 2.552,0.438 0.271,0.25 10 false *c 1.156,0.198 1.427,0.458 0.271,0.26 10 false *b
*a Turned Off
*b Turned On
*c Blinking


Allow the engine to idle until the D shift indicator comes on again.

Below Fluid Level Adjustment Temperature Fluid Level Adjustment Temperature Above Fluid Level Adjustment Temperature
35°C or less (95°F or less) 35 to 45°C (95 to 113°F) 45°C or more (113°F or more)
Shift Indicator (D)
Turned off
Shift Indicator (D)
Turned on
Shift Indicator (D)
Blinking

NOTICE:
·

If the D shift indicator is on, immediately proceed to the "Adjust Fluid Level" procedure.

·

If the D shift indicator blinks, stop the engine and wait until the fluid temperature drops to 35°C (95°F) or less (the indicator goes off). Then perform the "Adjust Fluid Temperature" procedure again from the beginning.



HINT:
·

In fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.

·

Fluid filling procedure should be performed when the D shift indicator is on (the fluid temperature is within the fluid level adjustment temperature range).




Hide 6.ADJUST FLUID LEVEL

CAUTION:

Use caution while the engine is idling and the radiator fan is operating.


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up.



b.
C201683
1.506,2.847 1.656,2.997 0.15,0.15 10 *1 1.506,3.683 1.667,3.835 0.161,0.152 10 *3 1.506,3.333 1.666,3.489 0.16,0.155 10 *2 1.468,2.927 0.981,2.927 false 1.468,3.42 1.009,3.42 false 1.468,3.763 0.956,3.763 false
*1 No. 1 Transmission Oil Filler Tube
*2 Overflow Plug
*3 Hexagon Socket Wrench


Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket.

CAUTION:

Be careful as the fluid coming out of the overflow plug hole is hot.



c.

Check the amount of fluid that comes out of the overflow plug hole.

NOTICE:

If only a small amount of fluid (approximately 1 cc) comes out of the overflow plug hole, then only fluid remaining in the No. 1 transmission oil filler tube has come out. This condition is not considered as overflow, so it is necessary to add fluid.



d.

If the fluid overflows

i.
C201682

Remove the refill plug and gasket.


ii.
C201690

Wait until the fluid flow slows and only drips come out.



e.

If the fluid does not overflow

i.
C201682

Remove the refill plug and gasket.


ii.
C201685

Add transaxle fluid through the refill hole until fluid comes out of the overflow plug hole.


iii.
C201686

Wait until the fluid flow slows and only drips come out.



f.
C201683
1.506,2.847 1.656,2.997 0.15,0.15 10 *1 1.506,3.683 1.667,3.835 0.161,0.152 10 *3 1.506,3.333 1.666,3.489 0.16,0.155 10 *2 1.468,2.927 0.981,2.927 false 1.468,3.42 1.009,3.42 false 1.468,3.763 0.956,3.763 false
*1 No. 1 Transmission Oil Filler Tube
*2 Overflow Plug
*3 Hexagon Socket Wrench


Install the overflow plug with a new gasket.

Torque:
40 N*m (408 kgf*cm, 29 ft.*lbf)


g.
C201682

Install the refill plug with a new gasket.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


h.

Lower the vehicle.


i.

Turn the ignition switch off.

HINT:

Turning the ignition switch off exits fluid temperature detection mode.



j.

Remove the intelligent tester from the DLC3 (when using the intelligent tester).


Hide 7. REBUILD WORK

a.

Lift the vehicle.


b.

Clean each part.


c.

Check for fluid leaks.


d.

Install the front wheel opening extension pad LH, engine under cover LH and front fender apron seal LH.


e.

Lower the vehicle.