Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT LEVER
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073979 SHIFT LEVER G

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 33560C 1.INSPECT LOWER SHIFT LEVER ASSEMBLY (w/o Smart Entry and Start System)

a.
C239820
2.052,1.479 2.313,0.5 2.313,0.5 2.49,0.5 false 1.792,1.49 1.688,0.427 1.688,0.427 1.51,0.427 false 1.781,1.698 1.781,2.573 1.781,2.573 1.635,2.573 false 2.052,1.698 2.667,2.802 2.667,2.802 2.813,2.802 false 0.073,0.063 0.333,0.323 0.26,0.26 10 true *a 1.281,0.333 1.563,0.563 0.281,0.229 10 false IG 1.323,2.5 1.792,2.781 0.469,0.281 10 false STP 2.563,0.427 3.094,0.74 0.531,0.313 10 false ACC 2.885,2.729 3.313,3.052 0.427,0.323 10 true KLS+
*a Component with harness connected
(Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (ACC) - Body ground Ignition switch ON 11 to 14 V
Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever except in P (Within approx. 1 second) 7.5 to 11 V
Ignition switch ACC and shift lever in P (After approx. 1 second) 6.0 to 9.5 V
4 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


HINT:

Do not disconnect the lower shift lever assembly connector.



b.
C239820
1.875,1.698 1.667,3.021 1.667,3.021 1.448,3.021 false 0.125,0.083 0.448,0.385 0.323,0.302 10 true *a 1.281,2.938 1.615,3.188 0.333,0.25 10 false E
*a Component with harness connected
(Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
7 (E) - Body ground Always Below 1 Ω


HINT:

Do not disconnect the lower shift lever assembly connector.



c.

Inspect shift lock solenoid

i.
C248595

Disconnect the shift lock solenoid connector.


ii.
C197452
1.313,1.198 0.635,1.542 false 1.604,1.219 1.396,1.563 false 1.854,1.219 2.146,1.542 false 2.094,1.167 2.781,1.542 false 0.146,0.156 0.458,0.458 0.313,0.302 10 false *a 0.5,1.583 0.917,1.833 0.417,0.25 10 false SLS+ 1.229,1.583 1.688,1.823 0.458,0.24 10 false SLS- 2.135,1.594 2.479,1.844 0.344,0.25 10 false E2 2.813,1.552 3.063,1.823 0.25,0.271 10 false P
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Shift Lever Position Specified Condition
4 (P) - 3 (E2) P 10 kΩ or higher
Other than P Below 1 Ω


·

If the result is not as specified, replace the lower shift lever assembly.

·

If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω


·

If the result is not as specified, replace the lower shift lever assembly.

·

If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.




Hide 33560C 2.INSPECT LOWER SHIFT LEVER ASSEMBLY (w/ Smart Entry and Start System)

a.
C239819
1.865,1.51 2.135,0.427 2.135,0.427 2.271,0.427 false 1.781,1.51 1.51,0.427 1.51,0.427 1.354,0.427 false 0.146,0.135 0.594,0.51 0.448,0.375 10 true *a 1.125,0.354 1.417,0.583 0.292,0.229 10 false IG 2.323,0.344 2.729,0.552 0.406,0.208 10 false STP
*a Component with harness connected
(Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
4 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V


HINT:

Do not disconnect the lower shift lever assembly connector.



b.
C239819
2.063,1.51 2.333,0.427 2.333,0.427 2.469,0.427 false 0.083,0.063 0.49,0.438 0.406,0.375 10 true *a 2.542,0.344 2.802,0.563 0.26,0.219 10 true E
*a Component with harness connected
(Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (E) - Body ground Always Below 1 Ω


HINT:

Do not disconnect the lower shift lever assembly connector.



c.

Inspect shift lock solenoid

i.
C248595

Disconnect the shift lock solenoid connector.


ii.
C197452
1.313,1.198 0.635,1.542 false 1.604,1.219 1.396,1.563 false 1.854,1.219 2.146,1.542 false 2.094,1.167 2.781,1.542 false 0.146,0.156 0.458,0.458 0.313,0.302 10 false *a 0.5,1.583 0.917,1.833 0.417,0.25 10 false SLS+ 1.229,1.583 1.688,1.823 0.458,0.24 10 false SLS- 2.135,1.594 2.479,1.844 0.344,0.25 10 false E2 2.813,1.552 3.063,1.823 0.25,0.271 10 false P
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Shift Lever Position Specified Condition
4 (P) - 3 (E2) P 10 kΩ or higher
Other than P Below 1 Ω


·

If the result is not as specified, replace the lower shift lever assembly.

·

If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω


·

If the result is not as specified, replace the lower shift lever assembly.

·

If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.




Hide 3.INSPECT TRANSMISSION CONTROL SWITCH (for LHD)

a.
C239095
2.323,1.25 2.74,1.427 false 2.052,1.333 2.448,1.698 false 1.74,1.323 1.969,1.823 false 1.427,1.323 1.24,1.802 false 1.115,1.313 0.865,1.646 false 0.25,0.135 0.729,0.344 0.479,0.208 10 *a 2,1.813 2.417,1.99 0.417,0.177 10 SFTU 2.802,1.375 3.219,1.552 0.417,0.177 10 SFTD 0.75,1.656 0.906,1.833 0.156,0.177 10 S 2.51,1.646 2.677,1.813 0.167,0.167 10 E 1.104,1.854 1.292,2.063 0.188,0.208 10 IG
*a Component without harness connected
(Transmission Control Switch)


Measure the resistance between each terminal of the shift lock control unit assembly when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
Shift lever not in S, "+" or "-" 10 kΩ or higher
3 (SFTU) - 2 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+" 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-" 10 kΩ or higher


If the resistance value is not as specified, replace the lower shift lever assembly.


Hide 4.INSPECT TRANSMISSION CONTROL SWITCH (for RHD)

a.
C239095
2.333,1.271 2.729,1.458 false 2.073,1.281 2.469,1.646 false 1.802,1.313 2.042,1.844 false 1.417,1.323 1.198,1.833 false 1.115,1.313 0.896,1.656 false 0.25,0.135 0.469,0.344 0.219,0.208 10 false *a 2.792,1.458 3.292,1.698 0.5,0.24 10 false SFTU 1.99,1.885 2.49,2.094 0.5,0.208 10 false SFTD 0.823,1.708 1.052,1.927 0.229,0.219 10 false S 2.531,1.656 2.813,1.906 0.281,0.25 10 false E 1.125,1.875 1.427,2.115 0.302,0.24 10 false IG
*a Component without harness connected
(Transmission Control Switch)


Measure the resistance between each terminal of the shift lock control unit assembly when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
Shift lever not in S, "+" or "-" 10 kΩ or higher
1 (SFTU) - 2 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+" 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-" 10 kΩ or higher


If the resistance value is not as specified, replace the lower shift lever assembly.