Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2011.10–2015.04
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073982 AUTOMATIC TRANSAXLE UNIT A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 35104V 1.REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.
C134951

Using a screwdriver, remove the transmission breather hose sub-assembly from the transaxle case sub-assembly.


b.
C134952C05
2.938,2.385 2.938,2.667 false 2.021,2.479 2.458,2.479 false 1.667,1.719 2.021,1.719 false 0.646,0.865 0.802,0.594 0.802,0.594 0.938,0.594 false 1.417,1.646 1.698,1.906 0.281,0.26 10 false *2 0.99,0.521 1.229,0.75 0.24,0.229 10 false *1 1.823,2.396 1.979,2.552 0.156,0.156 10 false *3 2.865,2.75 3.156,3.052 0.292,0.302 10 false *4
*1 No. 1 Breather Plug
*2 Breather Plug Hose
*3 No. 2 Breather Plug
*4 O-ring


Using a screwdriver, remove the No. 1 breather plug from the breather plug hose.


c.

Using a screwdriver, remove the No. 2 breather plug from the breather plug hose.


d.

Using a screwdriver, remove the O-ring from the No. 2 breather plug.


Hide 35572A 2.REMOVE TRANSMISSION CONTROL SHAFT LEVER

a.
C136685

Remove the nut, washer, and transmission control shaft lever from the manual valve lever shaft sub-assembly.


Hide 84540 3.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C136686

Remove the 2 bolts and the park/neutral position switch assembly from the transaxle case sub-assembly.

NOTICE:

Before removing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to remove the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



Hide 32921C 4.REMOVE OIL COOLER TUBE UNION (OUTLET)

a.
C205117

Remove the oil cooler tube union (outlet) from the transaxle case sub-assembly.


b.

Remove the O-ring from the oil cooler tube union (outlet).


Hide 5.REMOVE OIL COOLER TUBE UNION (INLET)

a.
C205116

Remove the oil cooler tube union (inlet) from the transaxle case sub-assembly.


b.

Remove the O-ring from the oil cooler tube union (inlet).


Hide 35104Q 6.REMOVE NO. 1 TRANSAXLE CASE PLUG

a.
C162438

Remove the 3 No. 1 transaxle case plugs from the transaxle case sub-assembly.


b.

Using a screwdriver, remove the 3 O-rings from the 3 No. 1 transaxle case plugs.


Hide 35104R 7.REMOVE NO. 2 TRANSAXLE CASE PLUG

a.
C134959

Using a 6 mm hexagon socket wrench, remove the 3 No. 2 transaxle case plugs from the transaxle housing.


b.

Remove the 3 gaskets from the 3 No. 2 transaxle case plugs.


Hide 8.SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY

a.
C201308C03
0.552,1.625 0.948,1.865 false 2.677,1.646 2.438,1.875 false 2.729,1.521 3.094,1.771 0.365,0.25 10 false *1 0.354,1.49 0.594,1.708 0.24,0.219 10 false *1
*1 Wooden Block


Support the transaxle assembly on wooden blocks.


Hide 35106A 9.REMOVE OVERFLOW PLUG

a.
C201309

Using a 6 mm hexagon socket wrench, remove the overflow plug from the automatic transaxle oil pan sub-assembly.


b.

Remove the gasket from the overflow plug.


Hide 35125C 10.REMOVE NO. 1 TRANSMISSION OIL FILLER TUBE

a.
C201310

Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.


Hide 35106D 11.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C287291

Remove the 19 bolts and automatic transaxle oil pan sub-assembly from the transaxle case sub-assembly.

NOTICE:

Some fluid will remain in the automatic transaxle oil pan sub-assembly. Remove all the bolts, and carefully remove the automatic transaxle oil pan sub-assembly.



Hide 35168A 12.REMOVE AUTOMATIC TRANSAXLE OIL PAN GASKET

a.

Remove the automatic transaxle oil pan gasket.


Hide 35394 13.REMOVE TRANSMISSION OIL CLEANER MAGNET

a.
C201701C11
2.719,0.219 1.771,0.219 1.771,0.219 1.771,0.75 false 2.49,0.219 2.49,1.146 false 2.844,0.146 3.167,0.406 0.323,0.26 10 false *1
*1 Transmission Oil Cleaner Magnet


Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


Hide 35394 14.INSPECT TRANSMISSION OIL CLEANER MAGNET

Hide 35330 15.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.
C201702

Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.


b.
C201703

Remove the O-ring from the valve body oil strainer assembly.


Hide 35410 16.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C201704

Remove the 11 bolts and transmission valve body assembly from the transaxle case sub-assembly.

NOTICE:

When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and the transaxle case sub-assembly to interfere with each other.



Hide 35145C 17.REMOVE NO. 1 GOVERNOR APPLY GASKET

a.
C201316

Remove the 2 No. 1 governor apply gaskets from the transaxle case sub-assembly.


Hide 35015S 19.REMOVE REFILL PLUG

a.
C136430

Remove the refill plug from the rear transaxle cover sub-assembly.


b.

Remove the gasket from the refill plug.


Hide 35102B 20.REMOVE REAR TRANSAXLE COVER PLUG

a.
C201317

Remove the 3 rear transaxle cover plugs from the rear transaxle cover sub-assembly.


b.

Using a screwdriver, remove the 3 O-rings from the 3 rear transaxle cover plugs.


Hide 35102 21.REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY

a.
C274845

Remove the 14 bolts from the rear transaxle cover sub-assembly.


b.

Using a brass bar and a hammer, tap on the circumference of the rear transaxle cover sub-assembly to remove the rear transaxle cover sub-assembly from the transaxle case sub-assembly.


c.
C274807

Using a screwdriver, remove the 3 O-rings from the transaxle case sub-assembly.


d.
C202908C05
1.375,1.75 1.375,0.188 1.375,0.188 1.813,0.188 false 1.604,1.635 1.604,0.188 false 0.583,2.25 0.385,2.375 0.385,2.375 0.385,2.458 false 0.99,0.719 1.083,0.719 1.083,0.719 1.083,1.823 false 1.885,0.135 2.094,0.313 0.208,0.177 10 false *1 0.792,0.646 0.979,0.969 0.188,0.323 10 false *2 0.323,2.51 0.51,2.833 0.188,0.323 10 false *3
*1 Oil Seal Ring
*2 Thrust Needle Roller Bearing
*3 No. 4 Thrust Needle Roller Race


Using a screwdriver, remove the 2 oil seal rings from the rear transaxle cover sub-assembly.


e.

Remove the thrust needle roller bearing and No. 4 thrust needle roller race from the rear transaxle cover sub-assembly.


f.
C201318

Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws and rear transaxle cover plate from the rear transaxle cover sub-assembly.


g.
C194888C06
1.354,0.938 1.51,0.938 false 1.073,0.885 1.396,1.063 0.323,0.177 10 true SST 3,0.375 3.177,0.552 0.177,0.177 10 false *a 0.354,0.833 0.531,1.01 0.177,0.177 10 false *b
*a Turn
*b Hold


Using SST, remove the needle roller bearing from the rear transaxle cover sub-assembly.

SST
09319-60020  


Hide 35650 22.REMOVE REAR MULTIPLE DISC CLUTCH ASSEMBLY

a.
C202901C04
0.646,1.302 0.385,1.563 0.385,1.563 0.385,1.979 false 2.406,0.354 2.146,0.354 2.146,0.354 2.146,1.375 false 2.49,0.281 2.771,0.552 0.281,0.271 10 false *1 0.313,2.042 0.604,2.323 0.292,0.281 10 false *2
*1 Thrust Needle Roller Bearing
*2 Rear Multiple Disc Clutch Assembly


Remove the rear multiple disc clutch assembly from the transaxle case sub-assembly.


b.

Remove the thrust needle roller bearing from the transaxle case sub-assembly.


c.
C224456C04
1.76,0.229 1.938,0.229 false 1.635,1.906 1.469,1.906 false 2,0.156 2.323,0.427 0.323,0.271 10 false *1 1.25,1.833 1.51,2.063 0.26,0.229 10 false *2
*1 O-ring
*2 Oil Seal Ring


Using a screwdriver, remove the O-ring from the rear multiple disc clutch assembly.


d.

Using a screwdriver, remove the oil seal ring from the rear multiple disc clutch assembly.


Hide 35730 23.REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

a.
C201320C03
2.594,0.146 2.479,0.146 2.479,0.146 2.104,0.552 false 2.677,0.083 3.01,0.333 0.333,0.25 10 false *1
*1 Snap Ring


Using 2 screwdrivers and a hammer, tap out the snap ring from the rear multiple disc clutch assembly.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



b.
C201321C05
0.463,0.472 0.639,0.657 0.176,0.186 10 *1 1.317,0.278 0.543,0.397 0.543,0.397 0.543,0.457 false
*1 Rear Planetary Sun Gear


Remove the rear planetary sun gear assembly from the rear multiple disc clutch assembly.


c.
C201526C04
2.115,0.896 2.229,1.01 2.229,1.01 2.229,1.333 false 1.51,0.281 1.865,0.281 false 1.26,0.198 1.563,0.5 0.302,0.302 10 false *1 2.146,1.375 2.469,1.677 0.323,0.302 10 false *2
*1 Thrust Needle Roller Bearing
*2 Thrust Bearing Race


Remove the thrust needle roller bearing and thrust bearing race from the rear multiple disc clutch assembly.


Hide 35111C 25.REMOVE TRANSAXLE HOUSING

a.
C205232

Remove the 20 bolts from the transaxle housing.


b.

Using a brass bar and a hammer, tap on the circumference of the transaxle housing to remove the transaxle housing from the transaxle case sub-assembly.


Hide 26.REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (OUTER RACE)

a.
C201323N06
2.479,0.479 2.104,0.479 false 2.542,0.406 3,0.656 0.458,0.25 10 false SST

Using SST, remove the differential drive pinion tapered roller bearing RH (outer race) and shim from the transaxle housing.

SST
09308-00010  


Hide 35882A 27.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C201326

Remove the bolt, clamp, and differential gear lube apply tube from the transaxle housing.


Hide 35174 28.REMOVE TRANSAXLE HOUSING OIL SEPARATOR

a.
C201327

Remove the 3 bolts and transaxle housing oil separator from the transaxle housing.


Hide 35035 29.REMOVE FRONT OIL PUMP ASSEMBLY

a.
C201328C05
0.792,0.198 0.583,0.198 false 0.365,0.125 0.677,0.365 0.313,0.24 10 false *1
*1 O-ring


Remove the O-ring from the front oil pump assembly.


b.

Remove the 7 bolts and front oil pump assembly from the transaxle case sub-assembly.


c.
C201329

Remove the O-ring from the front oil pump assembly.


d.
C201330C04
1.406,1.521 0.844,1.521 false 1.344,0.26 1.51,0.26 1.51,0.26 1.948,0.635 false 1.177,0.667 1.396,0.667 1.396,0.667 1.875,1.01 false 0.917,0.594 1.219,0.938 0.302,0.344 10 false *2 1.104,0.167 1.365,0.427 0.26,0.26 10 false *1 0.604,1.438 0.927,1.677 0.323,0.24 10 false *3
*1 Thrust Bearing Race
*2 Thrust Needle Roller Bearing
*3 O-ring


Remove the thrust needle roller bearing and thrust bearing race from the counter drive gear nut.


e.

Remove the O-ring from the transaxle case sub-assembly.


Hide 35683B 30.REMOVE NO. 3 BRAKE DISC

a.
C224457

Using a screwdriver, remove the snap ring from the front oil pump assembly.


b.
C136452C06
2.135,0.406 2.323,0.406 false 2.146,1.25 2.354,1.25 false 2.156,0.719 2.229,0.719 2.229,0.719 2.229,1.635 false 2.229,1.635 2.156,1.635 false 0.99,1.99 1.323,1.99 false 1.313,1 1.021,1 false 1.313,1.5 1.229,1.5 1.229,1.5 1.229,1 false 2.396,0.323 2.698,0.604 0.302,0.281 10 false *1 2.427,1.177 2.781,1.396 0.354,0.219 10 false *3 0.802,0.917 1.063,1.167 0.26,0.25 10 false *2 0.781,1.917 1.031,2.156 0.25,0.24 10 false *1
*1 Brake Flange
*2 Brake Plate
*3 Brake Disc


Remove the 2 brake flanges, 3 brake discs, and 2 brake plates from the front oil pump assembly.


Hide 34330 32.REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C136458

Remove the underdrive planetary gear assembly from the front oil pump assembly.


Hide 35663 33.REMOVE NO. 3 BRAKE HUB

a.
C136454

Remove the No. 3 brake hub from the underdrive planetary gear assembly.


b.
C202906C05
1.198,0.365 1.49,0.365 false 1.177,0.938 1.479,0.938 false 0.958,0.313 1.26,0.573 0.302,0.26 10 false *1 0.927,0.875 1.219,1.208 0.292,0.333 10 false *2
*1 Thrust Bearing Race
*2 Thrust Needle Roller Bearing


Remove the thrust needle roller bearing and thrust bearing race from the underdrive planetary gear assembly.


Hide 35706V 34.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C201331C04
1.292,0.271 1.406,0.271 1.406,0.271 1.667,0.833 false 1.563,3.021 1.271,3.021 false 2.448,1.375 2.344,1.375 2.344,1.375 1.99,2.146 false 1.083,0.188 1.25,0.354 0.167,0.167 10 *1 1.031,2.927 1.219,3.094 0.188,0.167 10 *3 2.49,1.281 2.688,1.458 0.198,0.177 10 *2
*1 Planetary Sun Gear Sub-assembly
*2 Underdrive Planetary Gear Assembly
*3 Snap Ring


While expanding the snap ring with snap ring pliers, remove the planetary sun gear from the underdrive planetary gear assembly.


b.

Remove the snap ring from the underdrive planetary gear assembly.


Hide 35.INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY

Hide 35701 37.REMOVE INPUT SHAFT SUB-ASSEMBLY

a.
C136459

Remove the input shaft sub-assembly from the front oil pump assembly.


b.
C202905C04
1.167,1.01 1.354,1.01 false 0.948,2.208 1.458,2.208 false 1.719,2.802 2.333,2.479 2.333,2.479 1.74,3.125 false 1.74,2.99 2.333,2.479 false 1.125,0.198 1.26,0.198 1.26,0.198 1.438,0.375 false 0.948,0.104 1.104,0.281 0.156,0.177 10 false *1 0.958,0.917 1.146,1.271 0.188,0.354 10 false *2 0.76,2.115 0.927,2.302 0.167,0.188 10 false *3 2.375,2.396 2.594,2.573 0.219,0.177 10 false *4
*1 Thrust Bearing Race
*2 Thrust Needle Roller Bearing
*3 Input Shaft sub-assembly
*4 Oil Seal Ring


Remove the thrust needle roller bearing and thrust bearing race from the input shaft sub-assembly.


c.

Using a screwdriver, remove the 3 oil seal rings from the input shaft sub-assembly.


Hide 34321 38.REMOVE UNDERDRIVE PLANETARY SUN GEAR

a.
C202904C05
2.313,1.49 2.229,1.49 2.229,1.49 2.01,1.406 false 1,0.448 1.438,0.448 false 0.781,0.365 0.958,0.542 0.177,0.177 10 false *1 2.375,1.417 3.281,1.76 0.906,0.344 10 false *2
*1 Underdrive Planetary Sun Gear
*2 Thrust Needle Roller Bearing


Remove the underdrive planetary sun gear from the front oil pump assembly.


b.

Remove the thrust needle roller bearing from the front oil pump assembly.


Hide 35681 39.REMOVE NO. 1 BRAKE DISC

a.
C153477C04
2.514,0.492 2.677,0.646 0.163,0.154 10 *1 2.198,0.578 2.489,0.578 false 2.2,1.164 2.331,1.164 2.331,1.164 2.331,0.578 false 0.862,0.802 1.029,0.956 0.167,0.154 10 *2 1.256,0.888 1.062,0.888 false
*1 Snap Ring
*2 Brake Snap Ring Stopper


Using a screwdriver, remove the 2 snap rings and brake snap ring stopper from the front oil pump assembly.


b.
C201529C04
1.448,0.219 1.677,0.219 1.677,0.219 1.979,0.594 false 2.75,1.479 2.99,1.479 false 2.75,1.021 2.875,1.021 2.875,1.021 2.875,1.969 false 2.875,1.969 2.76,1.969 false 1.938,1.292 1.51,1.292 false 1.938,2.177 1.74,2.177 1.74,2.177 1.74,1.292 false 1.927,1.719 1.74,1.719 false 1.219,0.156 1.51,0.427 0.292,0.271 10 false *1 1.271,1.219 1.563,1.479 0.292,0.26 10 false *2 3.073,1.406 3.323,1.667 0.25,0.26 10 false *3
*1 No. 1 Brake Flange
*2 No. 1 Brake Plate
*3 No. 1 Brake Disc


Remove the No. 1 brake flange, 3 No. 1 brake discs, and 3 No. 1 brake plates from the front oil pump assembly.


Hide 35608L 41.REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C136464

Remove the 3 2nd brake piston return springs from the front oil pump assembly.


Hide 42.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35621F 43.REMOVE NO. 1 BRAKE PISTON

a.
C136465

Holding the front oil pump assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the front oil pump assembly to remove the No. 1 brake piston.


b.
C274846

Using a screwdriver, remove the 2 O-rings from the No. 1 brake piston.


Hide 41311 44.REMOVE FRONT DIFFERENTIAL CASE

a.
C201332

Remove the front differential case from the transaxle case sub-assembly.


Hide 35782H 45.REMOVE COUNTER DRIVE GEAR NUT

a.
C201333N10
1.146,0.156 1.344,0.156 1.344,0.156 1.896,0.875 false 0.854,0.083 1.281,0.365 0.427,0.281 10 false SST

Using SST and a hammer, unstake the counter drive gear nut.

SST
09930-00010  


b.
C201334N09
1.151,3.98 1.291,4.135 0.14,0.154 10 P

Turn the manual valve lever shaft counterclockwise to set it to the P position as shown in the illustration.


c.
C201527N10
0.938,0.302 1.042,0.302 1.042,0.302 1.823,0.99 false 0.542,0.229 0.875,0.406 0.333,0.177 10 false SST

Using SST, remove the counter drive gear nut from the front planetary gear assembly.

SST
09387-00130  


d.
C201335N08
1.458,4.052 1.76,4.375 0.302,0.323 10 false N

Turn the manual valve lever shaft 2 notches clockwise to set it to the N position as shown in the illustration.


Hide 35783R 46.REMOVE COUNTER DRIVEN GEAR

a.
C201336

Remove the counter driven gear from the transaxle case sub-assembly.


Hide 41211J 47.REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (INNER RACE)

a.
C136470C03
2.219,0.833 2.615,0.99 2.615,0.99 2.26,1.26 false 1.844,1.229 2.615,0.99 false 1.698,1.271 0.927,1.208 false 2.646,0.896 3.01,1.063 0.365,0.167 10 false SST 0.615,1.125 1.031,1.354 0.417,0.229 10 false SST 0.302,0.552 0.615,0.708 0.313,0.156 10 false *b 2.646,0.073 2.958,0.25 0.313,0.177 10 false *a
*a Turn
*b Hold


Using SST, remove the differential drive pinion tapered roller bearing RH (inner race) from the counter driven gear.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00320)


Hide 41211K 48.REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (INNER RACE)

HINT:

If removing the differential drive pinion tapered roller bearing LH (inner race), replace the counter driven gear with a new one.


Hide 35558 49.REMOVE PAWL SHAFT CLAMP

a.
C201339

Remove the bolt and pawl shaft clamp from the transaxle case sub-assembly.


Hide 35165 50.REMOVE NO. 1 TRANSMISSION CASE PLATE

a.
C201340

Remove the bolt and No. 1 transmission case plate from the transaxle case sub-assembly.


Hide 35596 51.REMOVE PAWL STOPPER PLATE

a.
C201341

Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.


Hide 35598 52.REMOVE PARKING LOCK SLEEVE

a.
C201342

Remove the parking lock sleeve from the transaxle case sub-assembly.


Hide 35557 53.REMOVE PARKING LOCK PAWL

a.
C201343C04
0.41,1.376 0.587,1.549 0.177,0.173 10 *3 0.899,0.053 1.096,0.21 0.197,0.157 10 *1 1.625,0.424 1.803,0.604 0.178,0.18 10 *2 2.58,1.362 2.739,1.531 0.159,0.169 10 *4 0.608,1.463 0.697,1.463 0.697,1.463 0.988,1.547 false 0.899,0.135 0.771,0.135 0.771,0.135 1.023,1.247 false 1.605,0.505 1.531,0.505 1.531,0.505 1.411,1.302 false 2.553,1.443 2.439,1.443 2.439,1.443 2.074,1.735 false
*1 Parking Lock Pawl Pin
*2 Parking Lock Pawl Shaft
*3 Spring
*4 Parking Lock Pawl


Remove the spring, parking lock pawl pin, parking lock pawl shaft, and parking lock pawl from the transaxle case sub-assembly.


Hide 54.REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (OUTER RACE)

a.
C201344N06
1.385,0.531 1.792,0.531 false 1.031,0.448 1.365,0.594 0.333,0.146 10 false SST

Using SST, remove the differential drive pinion tapered roller bearing LH (outer race) from the transaxle case sub-assembly.

SST
09308-00010  


Hide 35790 55.REMOVE ONE-WAY CLUTCH ASSEMBLY

a.
C141525

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


b.
C141526C05
1.771,1.01 2.313,1.01 false 0.833,0.313 1.281,0.313 false 2.354,0.948 2.521,1.104 0.167,0.156 10 *2 0.615,0.229 0.771,0.375 0.156,0.146 10 *1
*1 One-way Clutch Assembly
*2 Thrust Needle Roller Bearing


Remove the one-way clutch assembly with the planetary ring gear from the transaxle case sub-assembly.


c.

Remove the thrust needle roller bearing from the front planetary gear assembly.


d.
C201345C04
1,0.156 1.177,0.156 1.177,0.156 1.313,0.385 false 1.125,1.417 1.385,1.417 false 2.521,0.979 2.802,1.052 2.802,1.052 2.802,1.135 false 0.813,0.073 1.083,0.313 0.271,0.24 10 false *1 0.938,1.333 1.104,1.51 0.167,0.177 10 false *3 2.729,1.208 3.01,1.49 0.281,0.281 10 false *2
*1 One-way Clutch Assembly
*2 Outer Race Retainer
*3 Planetary Ring Gear


Remove the one-way clutch assembly from the planetary ring gear.


e.

Remove the outer race retainer from the one-way clutch assembly.


Hide 35762E 57.REMOVE PLANETARY RING GEAR FLANGE

a.
C136480C07
1.271,0.646 0.969,0.646 false 0.958,2.302 1.219,2.302 false 2.063,1.302 2.406,1.302 false 0.719,2.208 0.896,2.375 0.177,0.167 10 false *3 2.479,1.219 2.802,1.49 0.323,0.271 10 false *2 0.719,0.552 0.896,0.719 0.177,0.167 10 false *1
*1 Snap Ring
*2 Planetary Ring Gear Flange
*3 Planetary Ring Gear


Using a screwdriver, remove the snap ring from the planetary ring gear.


b.

Remove the planetary ring gear flange from the planetary ring gear.


Hide 35682A 58.REMOVE NO. 2 BRAKE DISC

a.
C141524

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


b.
C238853C06
1.333,0.969 1.177,0.969 1.177,0.969 1.177,1.75 false 1.177,1.75 1.333,1.75 false 1.323,1.229 1.177,1.229 false 1.323,1.479 1.177,1.479 false 1.177,1.344 1.063,1.344 false 2.177,0.563 2.323,0.563 false 2.208,0.802 2.375,0.802 2.375,0.802 2.375,1.573 false 2.375,1.573 2.208,1.573 false 2.208,1.063 2.375,1.063 false 2.208,1.323 2.375,1.323 false 2.375,1.156 2.458,1.156 false 2.51,1.063 2.677,1.24 0.167,0.177 10 false *3 0.854,1.26 1.01,1.438 0.156,0.177 10 false *2 2.385,0.458 2.552,0.635 0.167,0.177 10 false *1
*1 No. 2 Brake Flange
*2 No. 2 Brake Plate
*3 No. 2 Brake Disc


Remove the No. 2 brake flange, 4 No. 2 brake discs, and 4 No. 2 brake plates from the transaxle case sub-assembly.


Hide 35068C 60.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C136482

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


b.
C136484

Remove the 1st and reverse brake return spring sub-assembly from the transaxle case sub-assembly.


Hide 61.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Hide 35622G 62.REMOVE NO. 2 BRAKE PISTON

a.
C136485

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the ATF hole to remove the No. 2 brake piston assembly from the transaxle case sub-assembly.


b.
C201346

Using a screwdriver, remove the 2 O-rings from the No. 2 brake piston.


Hide 35720 63.REMOVE FRONT PLANETARY GEAR ASSEMBLY

a.
C136674N07
2.62,1.242 2.966,1.407 0.346,0.166 10 SST 1.76,1.752 2.585,1.334 2.585,1.334 1.884,2.015 false

Using SST and a press, remove the planetary gear assembly from the transaxle case sub-assembly.

SST
09950-60010  (09951-00580)
09950-70010  (09951-07100)


Hide 35782C 64.REMOVE COUNTER DRIVE GEAR

a.
C201347N06
1.74,0.979 2.74,0.563 2.74,0.563 1.854,1.198 false 0.99,2.479 1.698,2.677 1.698,2.677 1.219,3.094 false 2.802,0.448 3.198,0.625 0.396,0.177 10 false SST 1.729,2.563 2.125,2.74 0.396,0.177 10 false SST

Using SST and a press, remove the counter drive gear and bearing inner race (rear side) from the transaxle case sub-assembly.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07100)


b.
C201348

As shown in the illustration, tighten the 2 bolts evenly and leave a clearance of approximately 5.0 mm (0.197 in.) between the counter drive gear and inner race.


c.
C201349C03
0.833,1.531 0.615,1.781 0.615,1.781 1.281,1.365 false 1.281,1.563 0.625,1.781 false 0.875,1.219 0.615,1.781 false 0.271,1.177 0.615,1.333 0.344,0.156 10 false *b 2.406,0.063 2.708,0.219 0.302,0.156 10 false *a 0.25,1.729 0.563,1.885 0.313,0.156 10 false SST
*a Turn
*b Hold


Using SST, remove the bearing inner race (front side) from the counter drive gear.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60020  (09951-00710)


Hide 35623 65.REMOVE NO. 3 BRAKE PISTON

a.
C201350N06
1.491,0.214 1.79,0.362 0.299,0.148 10 SST 1.839,0.302 1.931,0.302 1.931,0.302 2.078,0.603 false

Place SST on the brake piston return spring and compress the brake piston return spring with a press.

SST
09387-00070  


b.

Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.


c.
C201351C03
1.104,0.071 1.293,0.236 0.189,0.165 10 *1 1.325,0.157 1.497,0.157 1.497,0.157 1.602,0.851 false
*1 Brake Piston Return Spring


Remove the brake piston return spring from the transaxle case sub-assembly.


d.
C201352C07
0.91,0.138 1.114,0.304 0.203,0.166 10 *1 1.109,0.242 1.2,0.242 1.2,0.242 1.416,0.724 false
*1 No. 3 Brake Piston


Remove the No. 3 brake piston from the transaxle case sub-assembly.


e.
C201353

Using a screwdriver, remove the 2 O-rings from the No. 3 brake piston.


Hide 66.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35409 67.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C201354

Remove the bolt, manual detent spring cover, and manual detent spring sub-assembly from the transaxle case sub-assembly.


Hide 35501 68.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

a.
C201355

Remove the parking lock rod sub-assembly from the manual valve lever shaft.

HINT:

Align the slot with the notches on the manual valve lever shaft to remove the parking lock rod sub-assembly.



Hide 35506 69.REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY

a.
C201356

Using needle-nose pliers, remove the manual valve lever shaft retainer spring from the transaxle case sub-assembly.


b.
C201357

Remove the manual valve lever shaft sub-assembly from the transaxle case sub-assembly.


Hide 35506F 70.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C200899

Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case sub-assembly.