Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2011.10–2015.04
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073982 AUTOMATIC TRANSAXLE UNIT A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Check bearing position and installation direction.

C203284N07
0.521,3.224 0.653,3.401 0.132,0.177 10 A 2.237,3.898 2.369,4.075 0.132,0.177 10 B 3.346,5.066 3.478,5.243 0.132,0.177 10 C 4.634,5.727 4.766,5.904 0.132,0.177 10 D

C238855N07
2.26,5.884 2.433,6.057 0.173,0.173 10 E 4.61,6.585 4.783,6.758 0.173,0.173 10 H 1.085,8.489 1.258,8.662 0.173,0.173 10 F 2.29,8.79 2.463,8.963 0.173,0.173 10 G

Mark Front Race Diameter
Inside / Outside [mm (in.)]
Thrust Bearing Diameter
Inside / Outside [mm (in.)]
Rear Race Diameter
Inside / Outside [mm (in.)]
A - 57.7 (2.27) / 75.2 (2.96) -
B - 29.1 (1.15) / 48.6 (1.91) 30.7 (1.21) / 48.3 (1.90)
C - 62.6 (2.46) / 82.4 (3.24) 65.9 (2.59) / 82.3 (3.24)
D 59.4 (2.34) / 76 (2.99) 53.46 (2.10) / 79 (3.11) -
E - 56.1 (2.21) / 81.1 (3.19) -
F - 61.2 (2.41) / 79 (3.11) -
G - 28 (1.10) / 47.1 (1.85) 26.1 (1.03) / 44 (1.73)
H 52.2 (2.06) / 70.4 (2.77) 48.9 (1.93) / 72.0 (2.83) -


PROCEDURE

Hide 35782E 1.INSTALL COUNTER DRIVE GEAR BEARING

HINT:

Perform this procedure only when the counter drive gear bearing or transaxle case sub-assembly is replaced.


a.
C138721N08
2.413,0.816 2.755,0.978 0.341,0.163 10 SST 0.431,2.569 0.773,2.732 0.341,0.163 10 SST 1.589,1.012 2.376,0.902 2.376,0.902 1.76,1.183 false 1.621,2.114 0.832,2.653 0.832,2.653 1.645,2.47 false

Using SST and a press, install a new counter drive gear bearing and snap ring to the transaxle case sub-assembly.

SST
09950-60020  (09951-01030)
09950-70010  (09951-07100)


Hide 2.INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (OUTER RACE)

a.
C137443N04
1.417,1.094 0.333,1.479 0.333,1.479 1.313,1.344 false 0.031,1.406 0.354,1.573 0.323,0.167 10 SST

Using SST and a hammer, install a new differential drive pinion tapered roller bearing LH (outer race) to the transaxle case sub-assembly.

SST
09950-60010  (09951-00630)
09950-70010  (09951-07100)

NOTICE:

Make sure to install the differential drive pinion tapered roller bearing LH (outer race) so that there is no clearance between the differential drive pinion tapered roller bearing LH (outer race) and transaxle case sub-assembly. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



Hide 3.INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (OUTER RACE)

a.
C138261N06
1.75,0.854 2.927,1.698 2.927,1.698 1.865,1.344 false 2.979,1.635 3.344,1.885 0.365,0.25 10 false SST

Install the shim to the transaxle housing.


b.

Using SST, install a new differential drive pinion tapered roller bearing RH (outer race) to the transaxle housing.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07100)

NOTICE:

Make sure to install the differential drive pinion tapered roller bearing RH (outer race) so that there is no clearance between the differential drive pinion tapered roller bearing RH (outer race), shim and transaxle housing. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



Hide 41211J 4.INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (INNER RACE)

a.
C138250N06
2.528,0.672 2.897,0.852 0.369,0.179 10 SST 2.494,0.764 1.858,1.025 false

Using SST and a press, install a new differential drive pinion tapered roller bearing RH (inner race) to the counter driven gear.

SST
09950-60010  (09951-00490)

NOTICE:

Make sure to install the differential drive pinion tapered roller bearing RH (inner race) so that there is no clearance between the differential drive pinion tapered roller bearing RH (inner race) and counter driven gear. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



Hide 41211K 5.INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (INNER RACE)

a.
C138251N06
2.405,0.735 2.745,0.898 0.34,0.163 10 SST 1.874,1.143 2.379,0.83 false

Using SST and a press, install a new differential drive pinion tapered roller bearing LH (inner race) to the counter driven gear.

SST
09950-60010  (09951-00400)

NOTICE:

Make sure to install the differential drive pinion tapered roller bearing LH (inner race) so that there is no clearance between the differential drive pinion tapered roller bearing LH (inner race) and counter driven gear. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



Hide 6.ADJUST COUNTER DRIVEN GEAR PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.


b.
C317767

Install the counter driven gear to the transaxle case sub-assembly.


c.
C317768

Install the front differential case to the transaxle case sub-assembly.


d.
C274854N07
1.406,1.865 1.563,2.063 0.156,0.198 10 A 1.792,1.927 1.948,2.125 0.156,0.198 10 A 2.104,1.938 2.26,2.135 0.156,0.198 10 A

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
Bolt (A) : 23 N*m (231 kgf*cm, 17 ft.*lbf)
except Bolt (A) : 31 N*m (312 kgf*cm, 22 ft.*lbf)


e.
C317726N02
1.406,4.344 1.281,4.344 1.281,4.344 1.031,3.385 false 1.49,4.271 1.906,4.49 0.417,0.219 10 false SST

Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.

SST
09564-33010  

Turning Torque:

Differential side bearing preload + 2.9 to 6.1 N*m (30 to 62 kgf*cm, 26 to 53 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim for the differential drive pinion tapered roller bearing RH (outer race) so that the turning torque is within the specified range.

Shim Thickness
Thickness Thickness Thickness Thickness
2.000 (0.0787) 2.275 (0.0896) 2.550 (0.100) 2.825 (0.111)
2.025 (0.0797) 2.300 (0.0906) 2.575 (0.101) 2.850 (0.112)
2.050 (0.0807) 2.325 (0.0915) 2.600 (0.102) 2.875 (0.113)
2.075 (0.0817) 2.350 (0.0925) 2.625 (0.103) 2.900 (0.114)
2.100 (0.0827) 2.375 (0.0935) 2.650 (0.104) 2.925 (0.115)
2.125 (0.0837) 2.400 (0.0945) 2.675 (0.105) 2.950 (0.116)
2.150 (0.0846) 2.425 (0.0955) 2.700 (0.106) 2.975 (0.117)
2.175 (0.0856) 2.450 (0.0965) 2.725 (0.107) 3.000 (0.118)
2.200 (0.0866) 2.475 (0.0974) 2.750 (0.108) -
2.225 (0.0876) 2.500 (0.0984) 2.775 (0.109) -
2.250 (0.0886) 2.525 (0.0994) 2.800 (0.110) -


f.

Remove the 20 bolts and the transaxle housing.


g.

Remove the front differential case from the transaxle case sub-assembly.


h.

Remove the counter driven gear from the transaxle case sub-assembly.


Hide 35506F 7.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C188148N03
1.24,1.969 0.969,1.969 0.969,1.969 1.229,2.26 false 1.635,1.365 0.646,0.396 0.646,0.396 1.635,1.177 true 0.677,1.906 0.99,2.063 0.313,0.156 10 false SST 0.344,0.323 0.656,0.479 0.313,0.156 10 false SST

Coat the lip of a new manual valve lever shaft oil seal with a small amount of MP grease.


b.

Using SST and a hammer, tap in the manual valve lever shaft oil seal.

SST
09950-60010  (09951-00230)
09950-70010  (09951-07100)

Oil seal tap in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the oil seal is installed in the correct direction.



Hide 35506 8.INSTALL MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY

a.
C201357

Install the manual valve lever shaft sub-assembly to the transaxle case sub-assembly.

NOTICE:

Do not damage the manual valve lever shaft oil seal while installing the manual valve lever shaft sub-assembly to the transaxle case sub-assembly.



b.
C201356

Using needle-nose pliers, install the manual valve shaft retainer spring to the transaxle case sub-assembly.


Hide 35501 9.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.
C201355

Align the slot with the notches on the manual valve lever shaft sub-assembly and install the parking lock rod sub-assembly.


Hide 35409 10.INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C201354

Install the manual detent spring sub-assembly and manual detent spring cover to the transaxle case sub-assembly with the bolt.

Torque:
23 N*m (231 kgf*cm, 17 ft.*lbf)

NOTICE:

Make sure to install the manual detent spring sub-assembly first and then the manual detent spring cover.



Hide 35623 11.INSTALL NO. 3 BRAKE PISTON

a.
C201353

Coat 2 new O-rings with ATF and install them to the No. 3 brake piston.

NOTICE:

Ensure that the 2 O-rings are not twisted.



b.
C201352C08
1,0.198 1.177,0.198 1.177,0.198 1.417,0.708 false 0.781,0.125 1.042,0.344 0.26,0.219 10 false *1
*1 No. 3 Brake Piston


Temporarily install the No. 3 brake piston to the transaxle case sub-assembly.


c.
C201530C11
0.438,3.135 0.344,3.135 0.344,3.135 0.854,1.438 false 1.573,0.167 1.333,0.167 1.333,0.167 1.094,0.604 false 0.531,3.042 0.844,3.25 0.313,0.208 10 false *2 1.656,0.083 1.99,0.375 0.333,0.292 10 false *1
*1 No. 3 Brake Piston
*2 Pawl Stopper Plate


Temporarily install the pawl stopper plate to the transaxle case sub-assembly with the 2 bolts.

NOTICE:

After installing, make sure that the protrusions on the No. 3 brake piston and the grooves on the pawl stopper plate are aligned.



d.

Press the No. 3 brake piston into the transaxle case sub-assembly.

NOTICE:

Make sure that the lip of the No. 3 brake piston is not twisted and does not get caught in the transaxle case sub-assembly.


HINT:

Use the installation surface of the return spring to press the piston into the transaxle case sub-assembly.



e.

Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.


f.
C201531C04
2.302,1.208 2.198,1.208 2.198,1.208 0.771,0.385 false 2.354,0.229 0.688,0.323 false 2.406,0.146 2.594,0.458 0.188,0.313 10 *1 2.344,1.104 2.552,1.427 0.208,0.323 10 *2
*1 No. 3 Brake Piston
*2 Brake Piston Return Spring


Install the brake piston return spring to the transaxle case sub-assembly.

NOTICE:

Install the brake piston return spring as shown in the illustration.



g.

Place SST on the brake piston return spring and compress the brake piston return spring with a press.

C274848C07
1.448,1.469 0.792,0.531 0.792,0.531 0.656,0.531 true 4.49,0.417 4.74,0.417 4.74,0.417 5.01,1.198 true 0.375,0.448 0.667,0.625 0.292,0.177 10 false SST 4.281,0.323 4.594,0.521 0.313,0.198 10 false *1
*1 Snap Ring - -


SST
09387-00070  

NOTICE:

Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.



h.

Using a screwdriver, install the snap ring to the transaxle case sub-assembly as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.

·

Be sure to align the opening of the snap ring with one of the protrusions on the brake piston return spring as shown in the illustration.




Hide 35782C 12.INSTALL COUNTER DRIVE GEAR

a.
C137423N06
2.173,0.718 2.491,0.879 0.318,0.161 10 SST 2.133,0.787 1.876,0.896 false

Using SST and a press, install a new counter drive gear bearing inner race (front side) to the counter drive gear.

SST
09387-00020  


b.
C274849N04
1.667,3.76 2.104,3.938 2.104,3.938 1.698,3.938 true 1.156,2.656 1.469,2.656 1.469,2.656 1.302,3.052 true 1.5,2.594 1.958,2.792 0.458,0.198 10 SST 2.156,3.885 2.615,4.083 0.458,0.198 10 SST

Using SST, install a new counter drive gear bearing inner race (rear side) and counter drive gear to the transaxle case sub-assembly.

SST
09223-15030  
09527-17011  
09950-60020  (09951-00810)
09950-70010  (09951-07100)

NOTICE:

There should not be any clearance between the counter drive gear bearing inner race (front side) and counter drive gear.



Hide 35720 13.INSTALL FRONT PLANETARY GEAR ASSEMBLY

a.
C274850N04
1.906,0.792 2.323,0.375 true 1.844,2.563 2.052,2.563 true 1.844,3.979 2.052,3.979 2.052,3.979 1.823,3.75 true 2.365,0.302 2.823,0.5 0.458,0.198 10 SST 2.094,2.5 2.552,2.698 0.458,0.198 10 SST 2.094,3.927 2.552,4.125 0.458,0.198 10 SST

Using SST and a press, press in a new front planetary gear assembly to the transaxle case sub-assembly.

SST
09223-15030  
09527-17011  
09951-01100  


Hide 35622G 14.INSTALL NO. 2 BRAKE PISTON

a.
C201346

Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.

NOTICE:

Ensure that the 2 O-rings are not twisted.



b.
C138726

Install the No. 2 brake piston to the transaxle case sub-assembly.

NOTICE:

Be careful not to damage the O-rings.



Hide 35068C 15.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.

Install the 1st and reverse brake return spring to the transaxle case sub-assembly.

C274851N04
0.875,1.646 1.052,1.646 1.052,1.646 1.729,1.052 false 2.667,2.25 2.802,2.25 false 0.573,1.573 1.031,1.771 0.458,0.198 10 SST 2.854,2.198 3.313,2.396 0.458,0.198 10 SST


b.

Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring with a press.

SST
09387-00060  

NOTICE:

Stop the press when the 1st and reverse brake return spring is flush with the snap ring groove. This prevents the 1st and reverse brake return spring from being deformed.



c.

Using a screwdriver, install the snap ring to the transaxle case sub-assembly as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case sub-assembly as shown in the illustration.




Hide 35682A 16.INSTALL NO. 2 BRAKE DISC

a.
C238853C06
1.333,0.969 1.177,0.969 1.177,0.969 1.177,1.75 false 1.177,1.75 1.333,1.75 false 1.323,1.229 1.177,1.229 false 1.323,1.479 1.177,1.479 false 1.177,1.344 1.063,1.344 false 2.177,0.563 2.323,0.563 false 2.208,0.802 2.375,0.802 2.375,0.802 2.375,1.573 false 2.375,1.573 2.208,1.573 false 2.208,1.063 2.375,1.063 false 2.208,1.323 2.375,1.323 false 2.375,1.156 2.458,1.156 false 2.51,1.063 2.677,1.24 0.167,0.177 10 false *3 0.854,1.26 1.01,1.438 0.156,0.177 10 false *2 2.385,0.458 2.552,0.635 0.167,0.177 10 false *1
*1 No. 2 Brake Flange
*2 No. 2 Brake Plate
*3 No. 2 Brake Disc


Install the 4 No. 2 brake discs, 4 No. 2 brake plates, and No. 2 brake flange to the transaxle case sub-assembly.

NOTICE:

Make sure that the discs, plates, and flange are installed in the correct order.



b.
C201490

Using a screwdriver, install the snap ring to the transaxle case sub-assembly.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case sub-assembly as shown in the illustration.




Hide 35762E 18.INSTALL PLANETARY RING GEAR FLANGE

a.
C136480C07
1.271,0.646 0.969,0.646 false 0.958,2.302 1.219,2.302 false 2.063,1.302 2.406,1.302 false 0.719,2.208 0.896,2.375 0.177,0.167 10 false *3 2.479,1.219 2.802,1.49 0.323,0.271 10 false *2 0.719,0.552 0.896,0.719 0.177,0.167 10 false *1
*1 Snap Ring
*2 Planetary Ring Gear Flange
*3 Planetary Ring Gear


Install the planetary ring gear flange to the planetary ring gear.


b.

Using a screwdriver, install the snap ring to the planetary ring gear.

NOTICE:

Confirm that the snap ring is correctly located in the groove of the planetary ring gear.



Hide 35790 19.INSTALL ONE-WAY CLUTCH ASSEMBLY

a.
C201345C04
1,0.156 1.177,0.156 1.177,0.156 1.313,0.385 false 1.125,1.417 1.385,1.417 false 2.521,0.979 2.802,1.052 2.802,1.052 2.802,1.135 false 0.813,0.073 1.083,0.313 0.271,0.24 10 false *1 0.938,1.333 1.104,1.51 0.167,0.177 10 false *3 2.729,1.208 3.01,1.49 0.281,0.281 10 false *2
*1 One-way Clutch Assembly
*2 Outer Race Retainer
*3 Planetary Ring Gear


Install the outer race retainer to the one-way clutch assembly.


b.

Install the one-way clutch assembly to the planetary ring gear.

NOTICE:

Make sure that the one-way clutch assembly is positioned in the correct direction as shown in the illustration.



c.

Coat the thrust needle roller bearing with ATF, and install it onto the front planetary gear assembly.

C274852C05
1.698,1.479 2.49,2.531 2.49,2.531 2.708,2.531 true 2.771,2.49 3.083,2.688 0.313,0.198 10 *1
*1 Thrust Needle Roller Bearing - -


Bearing Diameter
- Inside [mm (in.)] Outside [mm (in.)]
Bearing 56.1 (2.21) 81.1 (3.19)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



d.

Install the one-way clutch assembly with the planetary ring gear to the transaxle case sub-assembly.

NOTICE:

Make sure that there is no clearance between the retainer and the claw on the one-way clutch assembly. If there is any clearance, the spring of the retainer will be deformed.



e.
C136477

Using a screwdriver, install the snap ring to the transaxle case sub-assembly.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case sub-assembly as shown in the illustration.




Hide 35557 20.INSTALL PARKING LOCK PAWL

a.
C201343C05
0.41,1.376 0.587,1.549 0.177,0.173 10 *3 0.899,0.053 1.096,0.21 0.197,0.157 10 *1 1.625,0.424 1.803,0.604 0.178,0.18 10 *2 2.58,1.362 2.739,1.531 0.159,0.169 10 *4 0.608,1.463 0.697,1.463 0.697,1.463 0.988,1.547 false 0.899,0.135 0.771,0.135 0.771,0.135 1.023,1.247 false 1.605,0.505 1.531,0.505 1.531,0.505 1.411,1.302 false 2.553,1.443 2.439,1.443 2.439,1.443 2.074,1.735 false
*1 Parking Lock Pawl Pin
*2 Parking Lock Pawl Shaft
*3 Spring
*4 Parking Lock Pawl


Install the parking lock pawl to the transaxle case sub-assembly with the parking lock pawl shaft.


b.

Install the parking lock pawl pin to the transaxle case sub-assembly.


c.
C137444

Install the torsion spring to the parking lock pawl.

NOTICE:

Make sure that one end of the spring is secured in the hole of the transaxle case sub-assembly and the other end is positioned on the parking lock pawl as shown in the illustration.



Hide 35598 21.INSTALL PARKING LOCK SLEEVE

a.
C201342

Install the parking lock sleeve to the transaxle case sub-assembly.


Hide 35596 22.INSTALL PAWL STOPPER PLATE

a.
C201341

Install the pawl stopper plate to the transaxle case sub-assembly with the 2 bolts.

Torque:
23 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 35165 23.INSTALL NO. 1 TRANSMISSION CASE PLATE

a.
C203287N04
2.073,0.667 2.188,0.833 0.115,0.167 10 A

Clean and degrease the bolt and the installation hole in the transaxle case sub-assembly.


b.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the No. 1 transmission case plate to the transaxle case sub-assembly with the bolt.

Torque:
23 N*m (231 kgf*cm, 17 ft.*lbf)

HINT:

Tighten the bolt while part A of the No. 1 transmission case plate contacts the transaxle case sub-assembly as shown in the illustration.



Hide 35558 24.INSTALL PAWL SHAFT CLAMP

a.
C201339

Install the pawl shaft clamp to the transaxle case sub-assembly with the bolt.

Torque:
23 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 35783R 25.INSTALL COUNTER DRIVEN GEAR

a.
C201336

Install the counter driven gear to the transaxle case sub-assembly.


Hide 35782H 26.INSTALL COUNTER DRIVE GEAR NUT

a.
C201334N10
1.151,3.98 1.291,4.135 0.14,0.154 10 P

Turn the manual valve lever shaft sub-assembly counterclockwise to set it to the P position as shown in the illustration.


b.
C202887N01
0.719,2.75 0.865,2.75 0.865,2.75 1.583,1.833 true 0.417,2.688 0.76,2.906 0.344,0.219 10 false SST

Using SST, install a new counter drive gear nut to the front planetary gear assembly.

SST
09387-00130  

Torque:
120 N*m (1224 kgf*cm, 88 ft.*lbf)


c.
C201335N09
1.487,4.004 1.625,4.186 0.137,0.182 10 N

Turn the manual valve lever shaft sub-assembly 2 notches clockwise to set it to the N position as shown in the illustration.


d.

Remove the counter driven gear from the transaxle case sub-assembly.


e.
C320106N01
1.208,0.5 1.354,0.5 1.354,0.5 1.698,1.333 false 0.906,0.427 1.271,0.635 0.365,0.208 10 false SST

Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm.

SST
09387-00130  

Turning Torque:

0.1 to 0.8 N*m (1 to 8 kgf*cm, 1 to 7 in.*lbf)


If the measured value is not within the specified range, gradually tighten the nut until the turning torque falls within the specified range.

Maximum Torque:

180 N*m (1835 kgf*cm, 132 ft.*lbf)



f.
C201333N11
1.177,0.156 1.333,0.156 1.333,0.156 1.906,0.875 false 0.823,0.083 1.25,0.302 0.427,0.219 10 false SST

Using SST and a hammer, stake the front planetary gear assembly.

SST
09930-00010  


g.

Install the counter driven gear to the transaxle case sub-assembly.


Hide 41311 27.INSTALL FRONT DIFFERENTIAL CASE

a.
C201332

Install the front differential case to the transaxle case sub-assembly.


Hide 35621F 28.INSTALL NO. 1 BRAKE PISTON

a.
C274846

Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.

NOTICE:

Ensure that the 2 O-rings are not twisted.



b.
C138253

Install the No. 1 brake piston to the front oil pump assembly.

NOTICE:

Be careful not to damage the O-rings.



Hide 35608L 29.INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C136464

Install the 3 2nd brake piston return springs to the front oil pump assembly.

NOTICE:

Make sure that the 3 2nd brake piston return springs are installed onto the protrusions on the front oil pump assembly.



Hide 35681 30.INSTALL NO. 1 BRAKE DISC

a.
C201529C05
1.531,0.208 1.677,0.208 1.677,0.208 1.979,0.583 false 2.76,1.479 3,1.479 false 2.76,1.021 2.875,1.021 2.875,1.021 2.875,1.969 false 2.875,1.969 2.74,1.969 false 1.938,1.292 1.51,1.292 false 1.927,2.177 1.74,2.177 1.74,2.177 1.74,1.292 false 1.927,1.719 1.74,1.719 false 1.292,0.125 1.552,0.354 0.26,0.229 10 false *1 1.302,1.208 1.656,1.49 0.354,0.281 10 false *2 3.063,1.417 3.323,1.635 0.26,0.219 10 false *3
*1 No. 1 Brake Flange
*2 No. 1 Brake Plate
*3 No. 1 Brake Disc


Install the 3 No. 1 brake discs, 3 No. 1 brake plates, and No. 1 brake flange to the front oil pump assembly.

NOTICE:
·

Make sure that the discs, plates, and flange are installed in the correct order.

·

Be sure to install the flange in the correct direction.




b.
C189783N06
1.917,0.635 2.521,0.208 2.521,0.208 2.188,1.021 false 0.99,3.156 0.615,3.156 false 2.583,0.115 3.021,0.365 0.438,0.25 10 false SST 0.292,3.083 0.729,3.354 0.438,0.271 10 false (#1)

Place SST on the flange and compress the flange with a press.

SST
09387-00070  
09495-65040  

NOTICE:

Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.



c.

Using a screwdriver, install the snap ring to the front oil pump assembly as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the oil pump.

·

Make sure to align the protruding part of the snap ring with the indented part (#1) of the front oil pump and gear body assembly shown in the illustration to install the snap ring.




d.
C176220

Install the brake snap ring stopper to the front oil pump assembly.

NOTICE:

Be sure to install the brake snap ring stopper in the correct direction.



e.
C201519N05
2.458,0.99 2.854,0.99 false 2.938,0.917 3.323,1.167 0.385,0.25 10 false (#2)

Using a screwdriver, install the snap ring to the front oil pump assembly as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the oil pump.

·

Make sure to align the protruding part of the snap ring with the indented part (#2) of the front oil pump assembly shown in the illustration to install the snap ring.




f.
C153481C04
1.667,2.135 1.302,2.792 false 1.5,1.76 1.99,0.76 1.99,0.76 1.75,1.76 false 1.156,2.823 1.427,3.073 0.271,0.25 10 false *1 1.979,0.552 2.313,0.854 0.333,0.302 10 false *2 0.156,0.219 0.604,0.677 0.448,0.458 10 false *a
*1 Brake Snap Ring Stopper
*2 Snap Ring
*a Correctly Installed


Check that the brake snap ring stopper can be turned by hand.

NOTICE:

If the brake snap ring stopper cannot be turned by hand, the brake snap ring stopper may have been installed upside down, or the snap ring may not have been completely located in the groove on the oil pump. Remove and reinstall the snap ring and the brake snap ring stopper.



Hide 34321 32.INSTALL UNDERDRIVE PLANETARY SUN GEAR

a.
C202904C06
2.365,1.688 2.198,1.688 2.198,1.688 1.99,1.406 false 0.948,0.729 1.375,0.729 false 0.708,0.646 0.969,0.948 0.26,0.302 10 false *1 2.448,1.604 2.771,1.885 0.323,0.281 10 false *2
*1 Underdrive Planetary Sun Gear
*2 Thrust Needle Roller Bearing


Coat the thrust needle roller bearing with ATF, and install it to the front oil pump assembly.

Bearing Diameter
- Inside [mm (in.)] Outside [mm (in.)]
Bearing 57.7 (2.27) 75.2 (2.96)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.

Install the underdrive planetary sun gear to the front oil pump assembly.


Hide 35701 33.INSTALL INPUT SHAFT SUB-ASSEMBLY

a.
C202905C05
1.167,1.01 1.354,1.01 false 0.938,2.208 1.479,2.208 false 1.719,2.802 2.323,2.469 2.323,2.469 1.74,3.135 false 1.74,2.979 2.323,2.469 false 1.125,0.198 1.26,0.198 1.26,0.198 1.438,0.375 false 0.948,0.104 1.104,0.281 0.156,0.177 10 false *1 0.958,0.917 1.146,1.271 0.188,0.354 10 false *2 0.698,2.146 1,2.448 0.302,0.302 10 false *3 2.365,2.354 2.729,2.656 0.365,0.302 10 false *4
*1 Thrust Bearing Race
*2 Thrust Needle Roller Bearing
*3 Input Shaft
*4 Oil Seal Ring


Coat 3 new oil seal rings with ATF and install them to the input shaft sub-assembly.

NOTICE:

Do not expand the gap of the oil seal ring too much.



b.

Coat the thrust needle roller bearing and thrust bearing race with ATF, and install them on the input shaft sub-assembly.

Bearing and Race Diameter
- Inside [mm (in.)] Outside [mm (in.)]
Bearing 29.1 (1.15) 48.6 (1.91)
Race 30.7 (1.21) 48.3 (1.90)

NOTICE:

Be sure to install the thrust needle roller bearing in the correct direction.



c.
C136459

Install the input shaft to the front oil pump assembly.


Hide 35706V 34.INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C201331C05
1.302,0.292 1.417,0.292 1.417,0.292 1.698,0.844 false 1.563,3.021 1.271,3.021 false 2.448,1.375 2.344,1.375 2.344,1.375 1.969,2.135 false 1.083,0.188 1.25,0.354 0.167,0.167 10 false *1 1.083,2.948 1.271,3.115 0.188,0.167 10 false *3 2.49,1.281 2.688,1.458 0.198,0.177 10 false *2
*1 Planetary Sun Gear Sub-assembly
*2 Underdrive Planetary Gear Assembly
*3 Snap Ring


Using a snap ring expander, install the snap ring to the underdrive planetary gear assembly.


b.

Using a snap ring expander, install the planetary sun gear sub-assembly to the underdrive planetary gear assembly with the snap ring expanded.


Hide 35663 35.INSTALL NO. 3 BRAKE HUB

a.
C202906C06
1.156,0.188 1.281,0.188 1.281,0.188 1.479,0.323 false 1.208,1.167 1.323,1.167 1.323,1.167 1.49,1 false 0.938,0.104 1.219,0.365 0.281,0.26 10 false *1 0.99,1.083 1.167,1.458 0.177,0.375 10 false *2
*1 Thrust Bearing Race
*2 Thrust Needle Roller Bearing


Coat the thrust needle roller bearing with ATF and install it on the underdrive planetary gear assembly.

Bearing and Race Diameter
- Inside [mm (in.)] Outside [mm (in.)]
Bearing 62.6 (2.47) 82.4 (3.24)
Race 65.9 (2.59) 82.3 (3.24)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.

Coat the thrust bearing race with MP grease and install it to the No. 3 brake hub.


c.
C136454

Install the No. 3 brake hub to the underdrive planetary gear assembly.


Hide 34330 36.INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C136458

Install the underdrive planetary gear assembly to the front oil pump assembly.


Hide 35683B 37.INSTALL NO. 3 BRAKE DISC

a.
C136452C07
2.135,0.406 2.323,0.406 false 2.146,1.25 2.365,1.25 false 2.156,0.719 2.229,0.719 2.229,0.719 2.229,1.635 false 2.229,1.635 2.156,1.635 false 1.01,2.031 1.344,2.031 false 1.313,1.01 1.125,1.01 false 1.323,1.51 1.24,1.51 1.24,1.51 1.24,1.01 false 2.396,0.323 2.615,0.583 0.219,0.26 10 false *1 2.469,1.188 2.708,1.417 0.24,0.229 10 false *3 0.906,0.938 1.198,1.219 0.292,0.281 10 false *2 0.792,1.969 1.031,2.229 0.24,0.26 10 false *1
*1 No. 3 Brake Flange
*2 No. 3 Brake Plate
*3 No. 3 Brake Disc


Install the 2 No. 3 brake flanges, 3 No. 3 brake discs, and 2 No. 3 brake plates to the front oil pump assembly.

NOTICE:

Make sure that the discs, plates, and flanges are installed in the correct order.



b.
C274824N04
2.25,0.854 2.688,0.521 2.688,0.521 1.406,0.521 true 2.771,0.427 3.229,0.771 0.458,0.344 10 false (A)

Using a screwdriver, install the snap ring to the front oil pump assembly.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the oil pump.

·

Make sure that the snap ring ends are positioned as shown in the illustration (A).




Hide 35035 39.INSTALL FRONT OIL PUMP ASSEMBLY

a.
C201330C05
1.417,1.5 0.677,1.5 false 1.385,0.219 1.552,0.219 1.552,0.219 2,0.625 false 1.177,0.667 1.396,0.667 1.396,0.667 1.875,1.01 false 0.969,0.583 1.146,0.927 0.177,0.344 10 *2 1.177,0.125 1.365,0.281 0.188,0.156 10 *1 0.458,1.396 0.635,1.563 0.177,0.167 10 *3
*1 Thrust Bearing Race
*2 Thrust Needle Roller Bearing
*3 O-ring


Coat a new O-ring with ATF and install it to the transaxle case sub-assembly.


b.

Coat the thrust needle roller bearing and thrust bearing race with ATF and install them on the counter drive gear nut.

Bearing and Race Diameter
- Inside [mm (in.)] Outside [mm (in.)]
Bearing 53.46 (2.10) 79 (3.11)
Race 59.4 (2.34) 76 (2.99)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



c.
C201329

Coat a new O-ring with ATF and install it to the front oil pump assembly.


d.
C201328C06
0.792,0.188 0.604,0.135 false 0.427,0.052 0.583,0.24 0.156,0.188 10 *1
*1 O-ring


Install the front oil pump assembly to the transaxle case sub-assembly with the 7 bolts.

Torque:
23 N*m (231 kgf*cm, 17 ft.*lbf)


e.

Coat a new O-ring with ATF and install it to the front oil pump assembly.


Hide 35174 40.INSTALL TRANSAXLE HOUSING OIL SEPARATOR

a.
C201327

Clean and degrease the 3 bolts and the installation holes in the transaxle housing.


b.

Apply adhesive to 2 or 3 threads on the ends of the 3 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the transaxle housing oil separator to the transaxle housing with the 3 bolts.

Torque:
23 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 35882A 41.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C201326

Install the differential gear lube apply tube to the transaxle housing.

NOTICE:

Insert the differential gear lube apply tube into the transaxle housing until it makes contact with the stopper.



b.

Clean and degrease the bolt and the installation hole in the transaxle housing.


c.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the apply tube clamp to the differential gear lube apply tube with the bolt.

Torque:
23 N*m (231 kgf*cm, 17 ft.*lbf)

NOTICE:

There should be clearance between the differential lube apply tube and apply tube clamp.



Hide 35111C 42.INSTALL TRANSAXLE HOUSING

a.
C201495

Clean and degrease the contact surfaces between the transaxle housing and transaxle case sub-assembly.

NOTICE:

Make sure that there is no ATF on the contact surfaces.



b.

Apply FIPG to the transaxle case sub-assembly.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Apply FIPG in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.

·

After applying FIPG, install the transaxle housing to the transaxle case sub-assembly within 3 minutes and tighten the bolts within 20 minutes.




c.
C205494

Install the transaxle housing to the transaxle case sub-assembly with the 17 bolts.

Torque:
31 N*m (312 kgf*cm, 22 ft.*lbf)


d.
C205495

Clean and degrease the 3 bolts and the installation holes in the automatic transaxle assembly.


e.

Apply adhesive to 2 or 3 threads on the ends of the 3 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.

Install the 3 bolts.

Torque:
23 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 35730 44.INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

a.
C201526C05
2.125,0.885 2.24,1 2.24,1 2.24,1.323 false 1.5,0.104 1.719,0.104 1.719,0.104 1.875,0.219 false 1.281,0.042 1.542,0.292 0.26,0.25 10 false *1 2.156,1.365 2.427,1.646 0.271,0.281 10 false *2
*1 Thrust Needle Roller Bearing
*2 Thrust Bearing Race


Coat the thrust needle roller bearing and thrust bearing race with ATF, and install them to the direct multiple disc clutch assembly.

Bearing and Race Diameter
- Inside [mm (in.)] Outside [mm (in.)]
Bearing 28 (1.10) 47.1 (1.85)
Race 26.1 (1.03) 44 (1.73)

NOTICE:

Install the rear planetary sun gear thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.
C201321C06
1.313,0.333 0.646,0.333 0.646,0.333 0.646,0.677 false 0.552,0.74 0.844,1 0.292,0.26 10 false *1
*1 Rear Planetary Sun Gear


Install the rear planetary sun gear assembly to the direct multiple disc clutch assembly.


c.
C202900

Using a snap ring expander, install the snap ring to the direct multiple disc clutch assembly.


d.
C224456C05
1.984,0.109 2.17,0.279 0.186,0.17 10 *1 1.273,1.785 1.46,1.955 0.186,0.17 10 *2 1.781,0.195 1.961,0.195 false 1.644,1.881 1.483,1.881 false
*1 O-ring
*2 Oil Seal Ring


Coat a new O-ring with ATF and install it to the direct multiple disc clutch assembly.

NOTICE:

Ensure that the O-ring is not twisted.



e.

Coat a new oil seal ring with ATF and install it to the intermediate shaft.


Hide 35650 46.INSTALL REAR MULTIPLE DISC CLUTCH ASSEMBLY

a.
C202901C05
0.646,1.302 0.406,1.573 0.406,1.573 0.406,1.833 false 2.458,0.417 2.135,0.417 2.135,0.417 2.135,1.375 false 2.542,0.344 2.833,0.583 0.292,0.24 10 false *1 0.323,1.885 0.604,2.135 0.281,0.25 10 false *2
*1 Thrust Needle Roller Bearing
*2 Rear Multiple Disc Clutch Assembly


Coat the rear thrust needle roller bearing with ATF and install it on the transaxle case sub-assembly.

Bearing Diameter
- Inside [mm (in.)] Outside [mm (in.)]
Bearing 61.2 (2.41) 79 (3.11)


b.

Install the direct multiple disc clutch assembly to the transaxle case sub-assembly.


Hide 35102 48.INSTALL REAR TRANSAXLE COVER SUB-ASSEMBLY

a.
C205308N06
1.688,1.104 0.896,1.104 0.896,1.104 1.615,1.323 false 0.583,1.021 1.031,1.292 0.448,0.271 10 false SST

Using SST and a hammer, install a new needle roller bearing into the rear transaxle cover sub-assembly.

SST
09950-60010  (09951-00220)
09950-70010  (09951-07100)

Installation depth:

21.5 to 21.9 mm (0.846 to 0.862 in.)



b.
C201318

Clean and degrease the 2 "TORX" screws and the installation holes in the rear transaxle cover sub-assembly.


c.

Apply adhesive to 2 or 3 threads on the ends of the 2 "TORX" screws.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Using a T30 "TORX" socket wrench, install the rear transaxle cover plate to the rear transaxle cover sub-assembly with the 2 "TORX" screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.
C202908C06
1.385,1.75 1.385,0.125 1.385,0.125 1.885,0.125 false 1.604,1.635 1.604,0.125 false 0.698,2.438 0.5,2.563 0.5,2.563 0.5,2.646 false 1.021,0.719 1.115,0.719 1.115,0.719 1.115,1.823 false 1.938,0.042 2.146,0.229 0.208,0.188 10 false *1 0.802,0.625 1.063,0.948 0.26,0.323 10 false *2 0.427,2.698 0.698,3 0.271,0.302 10 false *3
*1 Oil Seal Ring
*2 Thrust Needle Roller Bearing
*3 Thrust Bearing Race


Coat the thrust needle roller bearing and thrust bearing race with ATF and install them on the rear transaxle cover sub-assembly.

Bearing and Race Diameter
- Inside [mm (in.)] Outside [mm (in.)]
Bearing 48.9 (1.93) 72.0 (2.83)
Race 52.2 (2.06) 70.4 (2.77)


f.

Coat 2 new oil seal rings with ATF and install them to the rear transaxle cover sub-assembly.


g.
C274807

Coat 3 new O-rings with ATF and install them to the transaxle case sub-assembly.


h.
C138271

Remove packing material from the contact surfaces between the rear transaxle cover sub-assembly and transaxle case sub-assembly.

NOTICE:

Make sure that there is no ATF on the contact surfaces.



i.

Apply FIPG to the transaxle case sub-assembly.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent.


NOTICE:
·

Apply FIPG in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.

·

After applying FIPG, install the rear transaxle cover sub-assembly to the transaxle case sub-assembly within 3 minutes and tighten the bolts within 20 minutes.




j.
C274855

Install the rear transaxle cover sub-assembly to the transaxle case sub-assembly with the 12 bolts.

Torque:
23 N*m (231 kgf*cm, 17 ft.*lbf)


k.
C274856

Clean and degrease the 2 bolts and the installation holes in the transaxle case sub-assembly.


l.

Apply adhesive to 2 or 3 threads on the ends of the 2 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



m.

Install the 2 bolts.

Torque:
17 N*m (172 kgf*cm, 12 ft.*lbf)


Hide 35102B 49.INSTALL REAR TRANSAXLE COVER PLUG

a.
C201317

Coat 3 new O-rings with ATF and install them to the 3 rear transaxle cover plugs.

NOTICE:

Ensure that the 3 O-rings are not twisted.



b.

Install the 3 rear transaxle cover plugs to the rear transaxle cover sub-assembly.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 35015S 50.INSTALL REFILL PLUG

a.
C162439

Install a new gasket to the refill plug.


b.

Install the refill plug to the rear transaxle cover sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 35148 52.INSTALL NO. 1 GOVERNOR APPLY GASKET

a.
C201316

Coat 2 new No. 1 governor apply gaskets with ATF.


b.

Install the 2 No. 1 governor apply gaskets onto the transaxle case sub-assembly.


Hide 35410 53.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C274836C05
1.031,2.469 1.188,2.667 0.156,0.198 10 false A 1.417,2.438 1.573,2.635 0.156,0.198 10 false A 1.76,2.438 1.917,2.635 0.156,0.198 10 false A 2.146,2.438 2.302,2.635 0.156,0.198 10 false A 1.719,0.5 1.875,0.698 0.156,0.198 10 false A 1.115,0.458 1.271,0.656 0.156,0.198 10 false B 0.771,0.479 0.927,0.677 0.156,0.198 10 false D 0.073,1.219 0.229,1.417 0.156,0.198 10 false C 0.052,2.208 0.281,2.448 0.229,0.24 10 false *a 0.083,2.01 0.24,2.208 0.156,0.198 10 false B 2.99,1.427 3.24,1.667 0.25,0.24 10 false *a 2.833,1.438 2.99,1.635 0.156,0.198 10 false B 0.698,2.594 0.854,2.792 0.156,0.198 10 false B
*a Positioning Bolt


Coat the O-ring of the transmission wire with ATF.


b.

Insert the pin of the manual valve lever into the groove on the end of the manual valve and install the transmission valve body assembly onto the automatic transaxle assembly with the 11 bolts.

Bolt Length
Bolt Length [mm (in.)]
A 25 (0.984)
B 30 (1.18)
C and D 35 (1.38)

Torque:
Bolt A, B, C : 11 N*m (110 kgf*cm, 8 ft.*lbf)
Bolt D : 9.6 N*m (98 kgf*cm, 85 in.*lbf)

NOTICE:
·

When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and automatic transaxle assembly to interfere with each other.

·

First, temporarily tighten the bolts marked (*a) in the illustration because they are positioning bolts.




Hide 35330 54.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.
C201703

Coat a new O-ring with ATF.


b.

Install the O-ring onto the valve body oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted.



c.
C201702

Install the valve body oil strainer assembly onto the transmission valve body assembly with the 2 bolts.

Torque:
9.6 N*m (98 kgf*cm, 85 in.*lbf)


Hide 35394 55.INSTALL TRANSMISSION OIL CLEANER MAGNET

a.
C201701C12
2.719,0.219 1.771,0.219 1.771,0.219 1.771,0.75 false 2.49,0.219 2.49,1.156 false 2.781,0.135 3.094,0.375 0.313,0.24 10 false *1
*1 Transmission Oil Cleaner Magnet


Install the 2 transmission oil cleaner magnets onto the automatic transaxle oil pan sub-assembly as shown in the illustration.


Hide 35168A 56.INSTALL AUTOMATIC TRANSAXLE OIL PAN GASKET

a.

Install a new automatic transaxle oil pan gasket onto the automatic transaxle oil pan sub-assembly.


Hide 35106D 57.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C202902

Install the automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket onto the automatic transaxle assembly with the 17 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

Completely remove any oil or grease from the contact surfaces of the transaxle case sub-assembly and oil pan sub-assembly with the gasket before installation.



b.
C202903

Clean and degrease the 2 bolts and the installation holes in the transaxle case sub-assembly.


c.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 35125C 58.INSTALL NO. 1 TRANSMISSION OIL FILLER TUBE

a.
C201310

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)


Hide 35106A 59.INSTALL OVERFLOW PLUG

a.
C201309

Using a 6 mm hexagon socket wrench, install the overflow plug and a new gasket to the automatic transaxle oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 29 ft.*lbf)


Hide 35104R 60.INSTALL NO. 2 TRANSAXLE CASE PLUG

a.
C134959

Clean and degrease the 3 No. 2 transaxle case plugs and the installation holes in the transaxle housing.


b.

Apply adhesive to 2 or 3 threads on the ends of the 3 No. 2 transaxle case plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the 3 new gaskets to the 3 No. 2 transaxle case plugs.


d.

Using a 6 mm hexagon socket wrench, install the 3 No. 2 transaxle case plugs to the transaxle housing with the gaskets.

Torque:
17 N*m (173 kgf*cm, 12 ft.*lbf)


Hide 35104Q 61.INSTALL NO. 1 TRANSAXLE CASE PLUG

a.
C162438

Coat 3 new O-rings with ATF and install them to the 3 No. 1 transaxle case plugs.

NOTICE:

Ensure that the 2 O-rings are not twisted.



b.

Install the 3 No. 1 transaxle case plugs to the transaxle case sub-assembly.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 62.INSTALL OIL COOLER TUBE UNION (INLET)

a.
C205116

Coat a new O-ring with ATF and install it to the oil cooler tube union (inlet).

NOTICE:

Ensure that the O-ring is not twisted.



b.

Install the oil cooler tube union (inlet) to the transaxle case sub-assembly as shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 32921C 63.INSTALL OIL COOLER TUBE UNION (OUTLET)

a.
C205117

Coat a new O-ring with ATF and install it to the oil cooler tube union (outlet).

NOTICE:

Ensure that the O-ring is not twisted.



b.

Install the oil cooler tube union (outlet) to the transaxle case sub-assembly.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 84540 64.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C136686

Temporarily install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.

NOTICE:

Before installing the park/neutral position switch assembly, remove any dirt or rust on the manual valve lever shaft sub-assembly. Be sure to install the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



b.
C135733C16
2.532,0.661 2.717,0.821 0.185,0.16 10 *1 1.701,1.332 2.499,0.754 2.499,0.754 1.699,1.456 false
*1 Protrusion


Align the protrusions of the park/neutral position switch assembly as shown in the illustration.


c.

Tighten the 2 bolts

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

After installing the park/neutral position switch assembly, confirm that the 2 protrusions on the switch are aligned.



Hide 35572A 65.INSTALL TRANSMISSION CONTROL SHAFT LEVER

a.
C136685

Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the washer and nut.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 35104V 66.INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.
C134952C06
2.938,2.396 2.938,2.677 false 2.021,2.479 2.458,2.479 false 1.656,1.719 2.01,1.719 false 0.646,0.875 0.802,0.604 0.802,0.604 0.938,0.604 false 1.427,1.646 1.635,1.875 0.208,0.229 10 false *2 1.01,0.521 1.26,0.781 0.25,0.26 10 false *1 1.823,2.396 2.135,2.677 0.313,0.281 10 false *3 2.854,2.76 3.125,3.073 0.271,0.313 10 false *4
*1 No. 1 Breather Plug
*2 Breather Plug Hose
*3 No. 2 Breather Plug
*4 O-ring


Coat a new O-ring with ATF and install it to the No. 2 breather plug.

NOTICE:

Ensure that the O-ring is not twisted.



b.

Install the No. 2 breather plug to the breather plug hose.


c.

Install the No. 1 breather plug to the breather plug hose.


d.
C238851C06
2.333,1.281 2.417,1.521 2.417,1.521 2.521,1.521 false 2.552,1.094 2.708,0.677 2.708,0.677 2.844,0.677 false 2.594,1.427 2.906,1.667 0.313,0.24 10 false *a 2.917,0.594 3.208,0.906 0.292,0.313 10 false *1
*1 No. 2 Breather Plug
*a Boss


Install the transmission breather plug hose sub-assembly to the transaxle case sub-assembly.

NOTICE:

Ensure that the stopper on the No. 2 breather plug is in contact with the side of the boss on the transaxle case sub-assembly.