Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › OIL PUMP
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073984 OIL PUMP A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  REASSEMBLY  


PROCEDURE

Hide 35301A 1.INSTALL FRONT OIL PUMP OIL SEAL

a.
C138515
2.563,1.51 1.698,0.938 false 2.604,1.438 3.219,1.833 0.615,0.396 10 SST

Coat the lip of a new front oil pump oil seal with a small amount of MP grease.


b.

Using SST and a hammer, install the front oil pump oil seal to the front oil pump body sub-assembly.

SST
09350-32014  (09351-32140)

NOTICE:

The seal end should be level with the outer edge of the front oil pump body sub-assembly.



Hide 35301B 2.INSTALL FRONT OIL PUMP BODY O-RING

a.
C138278

Coat a new front oil pump body O-ring with ATF and install it to the front oil pump body sub-assembly.

NOTICE:

Ensure that the O-ring is not twisted.



Hide 35322 3.INSTALL FRONT OIL PUMP DRIVEN GEAR

a.
C138277

Coat the front oil pump driven gear with ATF and install it to the front oil pump body sub-assembly with the marked side up.


Hide 35321 4.INSTALL FRONT OIL PUMP DRIVE GEAR

a.
C138276

Coat the front oil pump drive gear with ATF, and install it to the front oil pump body sub-assembly with the marked side up.


Hide 35370 5.INSTALL STATOR SHAFT ASSEMBLY

a.
C138275
1.438,2.604 1.656,2.875 0.219,0.271 10 false B 0.708,1.198 1.073,1.531 0.365,0.333 10 false A 1,0.573 1.323,0.833 0.323,0.26 10 false A 1.604,0.354 1.844,0.604 0.24,0.25 10 false A 2.292,0.531 2.531,0.74 0.24,0.208 10 false A 2.583,0.979 2.802,1.271 0.219,0.292 10 false A 2.573,1.615 2.833,1.917 0.26,0.302 10 false A 2.198,2.135 2.427,2.406 0.229,0.271 10 false A 1.729,2.271 1.938,2.51 0.208,0.24 10 false A 0.969,1.906 1.25,2.177 0.281,0.271 10 false A 2.198,2.802 2.521,3.094 0.323,0.292 10 false B 2.448,3.354 2.76,3.667 0.313,0.313 10 false B 2.333,4.083 2.563,4.344 0.229,0.26 10 false B 0.844,3.771 1.063,4.031 0.219,0.26 10 false B 0.854,3.115 1.156,3.479 0.302,0.365 10 false B 1.313,4.271 1.615,4.542 0.302,0.271 10 false B

Align each knock pin of the stator shaft assembly with the holes in the front oil pump body sub-assembly and install the stator shaft assembly to the front oil pump body sub-assembly with the 16 "TORX" bolts.

Bolt Length
Bolt Length [mm (in.)]
A 14 (0.551)
B 26 (1.02)


b.

Using a T30 "TORX" socket wrench, tighten the 16 "TORX" bolts.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)