Home › Drivetrain › CLUTCH › CLUTCH PEDAL › 2011.10–2013.07
RM19V0EQ _52 Drivetrain _014583 CLUTCH _0073991 CLUTCH PEDAL N

CLUTCH  CLUTCH PEDAL  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST CLUTCH PEDAL HEIGHT

a.

Turn back the floor carpet.


b.
C248161
2.521,3.813 2.813,3.813 false 2.021,0.948 2.333,0.948 false 0.896,1.656 0.896,1.531 0.896,1.531 1.302,1.25 false 2.406,0.865 2.698,1.135 0.292,0.271 10 false *a 0.833,1.677 1.125,2.042 0.292,0.365 10 false *b 2.875,3.74 3.146,4 0.271,0.26 10 false *c
*a Pedal Height Adjust Point
*b Push Rod Play and Free Play Adjust Point
*c Pedal Height


Check the pedal height.

Pedal height from floor:

171.9 to 181.9 mm (6.768 to 7.161 in.)


If necessary, adjust the pedal height.


c.

Adjust the pedal height. (w/ Cruise control system)

i.

Loosen the lock nut and turn the clutch switch assembly until the height is correct. Tighten the lock nut.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)



d.

Adjust the pedal height. (w/o Cruise control system)

i.

Loosen the lock nut and turn the clutch pedal stopper bolt until the height is correct. Tighten the lock nut.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)



e.

Install the floor carpet.


Hide 2.INSPECT CLUTCH PEDAL FREE PLAY AND PUSH ROD PLAY

a.
C102627
1.656,1.76 2.01,1.76 2.01,1.76 2.396,1.927 false 2.323,1.688 2.323,0.896 2.323,0.896 2.51,0.896 false 2.604,0.813 2.958,1.042 0.354,0.229 10 false *a 1.427,1.677 1.719,1.906 0.292,0.229 10 false *b
*a Push Rod Play
*b Pedal Free Play


Check that the pedal free play and push rod play are correct.

i.

Depress the pedal until clutch resistance is felt.

Pedal free play:

5.0 to 15.0 mm (0.197 to 0.591 in.)



ii.

Gently depress the pedal until the resistance begins to increase a little.

Push rod play at pedal top:

1.0 to 5.0 mm (0.0394 to 0.197 in.)




b.

Adjust the pedal free play and push rod play.

i.

Loosen the lock nut and turn the push rod until the free play and push rod play are correct.


ii.

Tighten the lock nut.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


iii.

After adjusting the pedal free play, check the pedal height.



Hide 3.INSPECT CLUTCH RELEASE POINT

a.
C287071
1.542,1.615 2.115,1.073 2.115,1.073 2.323,1.073 false 0.833,1.938 0.99,1.938 0.99,1.938 1.26,1.552 false 1.323,0.99 1.688,1.271 0.365,0.281 10 false *c 2.396,1.01 2.75,1.313 0.354,0.302 10 false *b 0.635,1.844 0.948,2.083 0.313,0.24 10 false *a
*a Full Stroke End Position
*b Release Point
*c 25 mm or more


Check the clutch release point.

i.

Pull the parking brake lever and install wheel chocks.


ii.

Start the engine and run it at idle.


iii.

Depress the clutch pedal and move the shift lever to reverse.


iv.

Gradually release the clutch pedal and measure the stroke distance from the contact point (the point at which the engine speed begins to drop) up to the full stroke end position.

Standard distance:

25 mm (0.984 in.) or more (From pedal stroke end position to release point)


If the distance is not as specified, perform the following operations:

·

Check the pedal height.

·

Check push rod play and pedal free play.

·

Bleed the clutch line.

·

Check the clutch cover assembly and disc assembly.