Home › Brake › BRAKE (FRONT) › FRONT BRAKE › 2011.10–2015.04
RM19V0EQ _54 Brake _014593 BRAKE (FRONT) _0074048 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C238490C01
2.281,1.229 3.031,1.24 3.031,1.24 2.302,1.302 true 3.094,1.156 3.406,1.313 0.313,0.156 10 *a
*a Matchmark


Align the matchmarks of the front disc and front axle hub, and install the front disc.

NOTICE:

When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.



Hide 47775 2.INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

a.

for ADVICS Made:

i.

Secure the front disc brake cylinder mounting in a vise.


ii.
C239550C02
1.177,1.563 1.177,1.573 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bushing dust boot.



iii.
C238493

Using a socket wrench (19 mm) and a hammer, install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.



Hide 47722 3.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

a.

Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1090 kgf*cm, 79 ft.*lbf)


Hide 47775 4.INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

a.

for PBR Made:

i.
C248020C01
0.885,1.188 0.896,1.188 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the seal surface of 2 new front disc brake bushing dust boots.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bushing dust boot.



ii.

Apply a light layer of lithium soap base glycol grease to the sliding part and the seal surface of the front disc brake cylinder slide pin.


iii.

Install the 2 front disc brake bushing dust boots to each front disc brake cylinder slide pin.



Hide 47769 5.INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING

a.

for ADVICS Made:

i.
C211757C06
1.719,1.177 1.74,1.177 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the No. 2 front disc brake cylinder slide pin.


ii.

Install a new front disc brake cylinder slide bushing to the front No. 2 disc brake cylinder slide pin.



Hide 47715D 6.INSTALL FRONT NO. 2 DISC BRAKE CYLINDER SLIDE PIN

a.

for ADVICS Made:

i.
C211758C06
1.229,0.948 1.24,0.948 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front No. 2 disc brake cylinder slide pin.


ii.
C238487

Install the front No. 2 disc brake cylinder slide pin to the front disc brake cylinder mounting.


iii.

Push the front No. 2 disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.



Hide 47715A 7.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.

for PBR Made:

i.

Install the 2 front disc brake cylinder slide pins to the front disc brake cylinder mounting.


ii.

Install the front disc brake bushing dust boot to the groove of the front disc brake cylinder mounting.



b.

for ADVICS Made:

i.
C211759C05
1.333,0.875 1.333,0.865 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front disc brake cylinder slide pin.


ii.
C238486

Install the front disc brake cylinder slide pin to the front disc brake cylinder mounting.


iii.

Push the front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.



Hide 47716 8.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

a.

for PBR Made:

i.
C246331

Install the front disc brake pad support plate.



Hide 04947 9.INSTALL FRONT DISC BRAKE FITTING KIT

a.

for ADVICS Made:

i.
C238494C02
2.135,0.469 2.219,0.469 false 1.313,0.458 1.208,0.458 false 2.135,4.135 2.25,4.135 false 1.302,4.125 1.177,4.125 false 2.25,0.396 2.542,0.688 0.292,0.292 10 *1 1.021,0.375 1.292,0.604 0.271,0.229 10 *2 1,4.052 1.333,4.354 0.333,0.302 10 *1 2.292,4.063 2.604,4.323 0.313,0.26 10 *2
*1 Front No. 1 Disc Brake Pad Support Plate
*2 Front No. 2 Disc Brake Pad Support Plate


Install the 2 front No. 1 disc brake pad support plates and 2 front No. 2 disc brake pad support plates to the front disc brake cylinder mounting.

NOTICE:

Be sure to install each front disc brake pad support plate in the correct position and direction.




Hide 04465 10.INSTALL FRONT DISC BRAKE PAD

a.

for PBR Made:

i.
C246370C01
0.493,0.211 0.666,0.368 0.173,0.157 10 *A 0.501,1.99 0.681,2.151 0.181,0.161 10 *B 0.389,2.863 0.55,3.024 0.161,0.161 10 *1 0.837,2.834 0.725,2.946 0.725,2.946 0.583,2.946 false
*A Outer Side
*B Inner Side
*1 Pad Wear Indicator


Install the 2 front brake pads to the front disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the front disc brake pads or the front disc.




Hide 04945 11.INSTALL FRONT ANTI-SQUEAL SHIM KIT

a.

for ADVICS Made:

i.
C239560

Install the front disc brake pad wear indicator plate to each front disc brake pad.

NOTICE:

Install each front disc brake pad wear indicator plate in the correct position and direction.



ii.
C239549C02
0.708,1.365 0.719,1.354 false
V100155

Disc Brake Grease


Apply disc brake grease to the inside of each front disc brake anti-squeal shim as shown in the illustration.


iii.
C239559

Install the front disc brake anti-squeal shim to each front disc brake pad.

NOTICE:
·

Install the front disc brake anti-squeal shims in the correct positions and directions.

·

Disc brake grease can seep out slightly from the area where the front disc brake anti-squeal shim is installed.

·

Make sure that disc brake grease is not applied onto the lining surface.





Hide 04465 12.INSTALL FRONT DISC BRAKE PAD KIT

a.

for ADVICS Made:

i.

Install the 2 front disc brake pads with front anti-squeal shim kit to the front disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the disc brake pads or the front disc.



ii.
C238483

Install the 2 anti-squeal springs to the front disc brake pads.

NOTICE:
·

When replacing the front disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.

·

Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.





Hide 47750 13.INSTALL DISC BRAKE CYLINDER ASSEMBLY

a.

for PBR Made:

i.
C248004C01
1.305,0.961 1.469,1.106 0.164,0.145 10 *a 0.368,1.39 0.55,1.572 0.182,0.182 10 *b
*a Hold
*b Turn


Hold the front disc brake cylinder slide pin, and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with 2 new bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)



b.

for ADVICS Made:

i.
C239568C01
1.032,1.453 1.205,1.604 0.173,0.151 10 *a 0.874,0.409 1.044,0.573 0.17,0.164 10 *b
*a Hold
*b Turn


Hold the front disc brake cylinder slide pin, and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.

Torque:
34 N*m (350 kgf*cm, 25 ft.*lbf)



Hide 47313A 14.CONNECT FRONT FLEXIBLE HOSE

a.

for PBR Made:

i.
C246328C01
2.947,0.953 3.114,1.1 0.166,0.147 10 *a 1.561,1.033 2.91,1.033 false
*a Lock Hole


Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and 2 new gaskets.

Torque:
30 N*m (305 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the flexible hose lock securely into the lock hole in the front disc brake cylinder.




b.

for ADVICS Made:

i.
C238481C03
2.74,0.288 2.915,0.446 0.175,0.159 10 *a 2.033,0.755 2.408,0.38 2.408,0.38 2.736,0.38 false
*a Lock Hole


Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
30 N*m (305 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the flexible hose lock securely into the lock hole in the front disc brake cylinder.




Hide 16.INSTALL FRONT WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)