Home › Brake › BRAKE (REAR) › REAR BRAKE › 2011.10–2015.04
RM19V0EQ _54 Brake _014594 BRAKE (REAR) _0074050 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.

·

Refer to the illustration to confirm the type of brake used.

C249686
0.173,0.054 0.367,0.255 0.194,0.200 10 *A 3.759,0.054 4.036,0.309 0.277,0.254 10 *B 6.338,2.322 6.511,2.494 0.173,0.172 10 *1 6.123,2.398 6.327,2.398 false 2.763,2.322 2.954,2.487 0.191,0.165 10 *1 2.536,2.398 2.74,2.398 false 5.767,1.352 5.954,1.556 0.187,0.204 10 *b 2.137,1.352 2.325,1.556 0.187,0.204 10 *a
*A for PBR Made *B for ADVICS Made
*1 Rear Disc - -
*a 190 to 191 mm (7.48 to 7.51 in.) *b 170 to 171 mm (6.69 to 6.73 in.)




PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47319F 3.SEPARATE REAR FLEXIBLE HOSE

a.

for PBR Made:

i.
C246335

Remove the union bolt and 2 gaskets, and separate the rear flexible hose from the rear disc brake cylinder assembly.



b.

for ADVICS Made:

i.
C243121

Remove the union bolt and gasket, and separate the rear flexible hose from the rear disc brake cylinder assembly.



Hide 47850 4.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.

for PBR Made:

i.
C248005C01
2.13,0.466 2.3,0.618 0.17,0.152 10 *a 3.072,0.739 3.242,0.887 0.17,0.148 10 *b
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pin, and remove the 2 bolts and rear disc brake cylinder assembly.



b.

for ADVICS Made:

i.
C239569
2.271,0.438 2.563,0.698 0.292,0.26 10 *b 2.75,1.917 3.135,2.229 0.385,0.313 10 *a
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pin, and remove the 2 bolts and rear disc brake cylinder assembly.



Hide 04466 5.REMOVE REAR DISC BRAKE PAD

a.

for PBR Made:

i.
C246337

Remove the 2 rear disc brake pads from the disc brake cylinder mounting.



b.

for ADVICS Made:

i.
C238499

Remove the 2 rear disc brake pads with rear disc brake anti-squeal shim kit from the disc brake cylinder mounting.



Hide 04946 6.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

a.

for ADVICS Made:

i.
C239558

Remove the rear disc brake anti-squeal shim from each rear disc brake pad.


ii.
C239557

Remove the rear disc brake pad wear indicator plate from each rear disc brake pad.



Hide 47716A 7.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

a.

for ADVICS Made:

i.
C238500

Remove the 2 rear disc brake pad support plates from the disc brake cylinder mounting.



Hide 47715C 8.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.

for PBR Made:

i.
C246338

Remove the 2 rear disc brake cylinder slide pins with rear disc brake bushing dust boot from the disc brake cylinder mounting.



Hide 47814 9.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN (for Upper Side)

a.

for ADVICS Made:

i.
C243122

Remove the rear disc brake cylinder slide pin from the disc brake cylinder mounting.



Hide 47814 10.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN (for Lower Side)

a.

for ADVICS Made:

i.
C243123

Remove the rear disc brake cylinder slide pin from the disc brake cylinder mounting.



Hide 11.REMOVE REAR DISC BRAKE CYLINDER SLIDE BUSHING

a.

for ADVICS Made:

i.
C210924
2.333,1.396 2.333,1 2.333,1 2.542,1 false 2.552,0.906 2.969,1.219 0.417,0.313 10 *1
*1 Vinyl Tape


Using a screwdriver with its tip wrapped with vinyl tape, remove the rear disc brake cylinder slide bushing from the rear disc brake cylinder slide pin.

NOTICE:

Do not damage the rear disc brake cylinder slide pin.




Hide 47775D 12.REMOVE REAR DISC BRAKE BUSHING DUST BOOT

a.

for PBR Made:

i.

Remove the rear disc brake bushing dust boot from each rear disc brake cylinder slide pin.



b.

for ADVICS Made:

i.
C243124

Remove the 2 rear disc brake bushing dust boots from the disc brake cylinder mounting.



Hide 47722A 13.REMOVE DISC BRAKE CYLINDER MOUNTING

a.

for PBR Made:

i.
C246339

Remove the 2 bolts and disc brake cylinder mounting.



b.

for ADVICS Made:

i.
C243125

Remove the 2 bolts and disc brake cylinder mounting.



Hide 42491 14.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Remove the parking brake shoe adjusting hole plug.


Hide 42431 15.REMOVE REAR DISC

a.
C143446C01
2.083,1.115 1.354,1.5 1.354,1.5 2.021,1.01 true 1.188,1.438 1.417,1.635 0.229,0.198 10 false *a
*a Matchmark


Put matchmarks on the rear disc and the rear axle hub.


b.
C201774

Release the parking brake and remove the rear disc.

HINT:

If the disc cannot be removed easily, use a screwdriver to turn the shoe adjuster as shown in the illustration in order to contract the parking brake shoes.