Home › Brake › BRAKE (REAR) › REAR BRAKE › 2011.10–2015.04
RM19V0EQ _54 Brake _014594 BRAKE (REAR) _0074050 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REASSEMBLY  


PROCEDURE

Hide 47547C 1.TEMPORARILY TIGHTEN REAR DISC BRAKE BLEEDER PLUG

HINT:

Fully tighten the rear disc brake bleeder plug after bleeding the system.


Hide 31478C 2.INSTALL REAR DISC BRAKE BLEEDER PLUG CAP

Hide 3.INSTALL PISTON SEAL

a.

Apply a light layer of lithium soap base glycol grease to the entire circumference of a new piston seal.


b.

Install the piston seal to the rear disc brake cylinder.

NOTICE:

Securely install the piston seal to the groove of the rear disc brake cylinder.



Hide 47731B 4.INSTALL REAR DISC BRAKE PISTON

a.

for ADVICS Made:

i.
C239554
1.184,1.021 1.34,1.173 0.156,0.152 10 *1 1.183,2.031 1.341,2.185 0.158,0.154 10 *2 0.98,1.114 1.148,1.114 false 0.929,2.126 1.148,2.126 false
*1 Cylinder Boot
*2 Rear Disc Brake Piston
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot.


ii.

Install the cylinder boot to the rear disc brake piston.


iii.

Apply a light layer of lithium soap base glycol grease to the contact surfaces of the rear disc brake piston, and install it to the rear disc brake cylinder.

NOTICE:

Do not install the rear disc brake piston forcibly in the rear disc brake cylinder.




Hide 5.INSTALL CYLINDER BOOT

a.

for PBR Made:

i.
C239545C03
2.511,0.401 2.667,0.557 0.156,0.156 10 *1 2.516,1.352 2.679,1.508 0.163,0.156 10 *2 2.191,0.477 2.48,0.477 false 2.077,1.44 2.48,1.44 false
*1 Cylinder Boot
*2 Rear Disc Brake Piston
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot and rear disc brake piston.


ii.
C248019

Install the cylinder boot to the rear disc brake piston.



b.

for ADVICS Made:

i.
C239555
0.75,1.218 0.905,1.368 0.155,0.15 10 *1 1.291,1.218 1.443,1.366 0.152,0.148 10 *2 0.835,0.949 0.835,1.23 false 1.366,1.063 1.366,1.212 false
*1 Set Ring
*2 Cylinder Boot


Install the cylinder boot to the rear disc brake cylinder.

NOTICE:

Securely install the cylinder boot to the groove of the rear disc brake cylinder and rear disc brake piston.



ii.

Using a screwdriver with its tip wrapped with vinyl tape, install a new rear disc brake piston set ring.

NOTICE:
·

Securely install the rear disc brake piston set ring to the outer groove of the cylinder boot.

·

Do not damage the cylinder boot.





Hide 47731B 6.INSTALL REAR DISC BRAKE PISTON

a.

for PBR Made:

i.
C145785C01
1.306,2.998 1.464,3.149 0.158,0.151 10 *1 0.969,2.657 1.134,2.812 0.165,0.155 10 *2 0.725,2.733 0.963,2.733 false 1.028,3.234 1.172,3.09 1.172,3.09 1.305,3.09 false
*1 Cylinder Boot
*2 Rear Disc Brake Piston


Install the cylinder boot securely to the grooves of the rear disc brake cylinder.

NOTICE:
·

Securely install the cylinder boot into the groove of the disc brake cylinder and rear disc brake piston.

·

Do not damage the cylinder boot.




ii.

Push in the piston by hand and install the boot onto the grooves of the piston.