Home › Brake › PARKING BRAKE › PARKING BRAKE SYSTEM › 2011.10–2013.07
RM19V0EQ _54 Brake _014595 PARKING BRAKE _0074052 PARKING BRAKE SYSTEM N

PARKING BRAKE  PARKING BRAKE SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT PARKING BRAKE PEDAL TRAVEL (for Automatic Transaxle)

a.

Fully depress the parking brake pedal to engage the parking brake.


b.

Depress the pedal again to disengage the parking brake.


c.

for PBR Made:

i.
C233618

Slowly depress the parking brake pedal using the specified force, and count the number of clicks.

Parking brake pedal travel (for LHD):

7 to 10 notches at 300 N (31 kgf, 67.5 lbf)


Parking brake pedal travel (for RHD):

9 to 12 notches at 300 N (31 kgf, 67.5 lbf)


If the parking brake pedal travel is not as specified, adjust the parking brake shoe clearance and parking brake pedal travel.



d.

for ADVICS Made:

i.

Slowly depress the parking brake pedal using the specified force, and count the number of clicks.

Parking brake pedal travel:

7 to 10 notches at 300 N (31 kgf, 67.5 lbf)


If the parking brake pedal travel is not as specified, adjust the parking brake shoe clearance and parking brake pedal travel.



Hide 2.INSPECT PARKING BRAKE LEVER TRAVEL (for Manual Transaxle)

a.

Firmly pull the parking brake lever.


b.

Release the parking brake lever lock and return it to its off position.


c.
C240907

Slowly pull the parking brake lever using the specified force, and count the number of clicks.

Parking brake lever travel:

7 to 10 notches at 200 N (20 kgf, 45.0 lbf)


If the parking brake lever travel is not as specified, adjust the parking brake shoe clearance and parking brake lever travel.


Hide 3.ADJUST PARKING BRAKE PEDAL TRAVEL (for Automatic Transaxle LHD)

a.

for PBR Made:

i.

Completely release the parking brake pedal.


ii.
C237831C01
0.854,1.531 2.396,1.531 true 0.802,1.625 1.979,1.979 1.979,1.979 2.385,1.979 true 2.427,1.896 2.583,2.063 0.156,0.167 10 *1 2.438,1.448 2.594,1.615 0.156,0.167 10 *2
*1 Lock Nut
*2 Adjusting Nut


Loosen the lock nut and the adjusting nut to completely release the parking brake cable.


iii.

Remove the rear wheels.


iv.

Separate the rear disc brake caliper assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


v.

Remove the parking brake shoe adjusting hole plug.


vi.

vii.
C240909

Measure the brake shoe diameter as shown in the illustration.

Standard diameter:

189.6 to 189.7 mm (7.46 to 7.47 in.)



viii.
C171323C01
1.146,1.167 1.146,1.865 false 1.073,1.885 1.458,2.104 0.385,0.219 10 false *1
*1 Nut


If the shoe diameter is not as specified, adjust it by turning the nut.


ix.
C171324N01
0.885,0.083 1.229,0.365 0.344,0.281 10 false (A)

The gap between the adjusting nut and screw must not exceed 5 mm (0.197 in.). If the gap is set to this specification and the shoe diameter is less than specified, replace the parking brake shoe. If the lining thickness is less than 1.5 mm (0.0591 in.) or exhibits uneven wear, replace the parking brake shoe.

Dimension (A):

5 mm (0.197 in.) max




xi.

Check for drag. Spin the rotor and ensure there is no drag from the parking brake shoe.

HINT:

If there is drag, apply and release the parking brake pedal and retest. If drag is still present, remove the disc, remeasure and readjust the shoe diameter and centralize the shoe. Reassemble the disc and recheck for drag.



xii.

Install the parking brake shoe adjusting hole plug.


xiii.

Install the rear disc brake caliper assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>INSTALLATION


xiv.

Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

Parking brake pedal travel:

7 to 10 notches at 300 N (31 kgf, 67.5 lbf)



xv.

Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


xvi.

Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.


xvii.

Check that the parking brake does not drag.


xviii.

Install the rear wheels.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)



b.

for ADVICS Made:

i.

Completely release the parking brake pedal.


ii.
C237831C01
0.854,1.531 2.396,1.531 true 0.802,1.625 1.979,1.979 1.979,1.979 2.385,1.979 true 2.427,1.896 2.583,2.063 0.156,0.167 10 *1 2.438,1.448 2.594,1.615 0.156,0.167 10 *2
*1 Lock Nut
*2 Adjusting Nut


Loosen the lock nut and the adjusting nut to completely release the parking brake cable.


iii.

Remove the rear wheels.


iv.

Temporarily install the hub nuts to the hub bolts.

HINT:

Securely install the hub nuts to the rear disc.



v.

Remove the parking brake shoe adjusting hole plug.


vi.
C239414C02
1.833,0.406 1.833,0.385 false
V100135

Expand
V100136

Contract


Turn the shoe adjuster and expand the shoes until the disc locks.


vii.

Turn and contract the shoe adjuster until the disc can rotate smoothly.

Standard:

Returns 8 notches.



viii.

Check that there is no brake drag against the shoes.


ix.

Install the parking brake shoe adjusting hole plug.


x.

Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

Parking brake pedal travel:

7 to 10 notches at 300 N (31 kgf, 67.5 lbf)



xi.

Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


xii.

Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.


xiii.

Check that the parking brake does not drag.


xiv.

Remove the hub nuts from the hub bolts.


xv.

Install the rear wheels.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)



Hide 4.ADJUST PARKING BRAKE PEDAL TRAVEL (for Automatic Transaxle RHD)

a.

for PBR Made:

i.

Completely release the parking brake pedal.


ii.
C247507C01
0.854,1.448 1.438,1.448 true 0.396,1.417 0.729,1.417 true 1.469,1.354 1.781,1.552 0.313,0.198 10 false *1 0.24,1.333 0.552,1.531 0.313,0.198 10 false *2
*1 Lock Nut
*2 Adjusting Nut


Loosen the lock nut and the adjusting nut to completely release the parking brake cable.


iii.

Remove the rear wheels.


iv.

Separate the rear disc brake caliper assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT


v.

Remove the parking brake shoe adjusting hole plug.



vii.
C240909

Measure the brake shoe diameter as shown in the illustration.

Standard diameter:

189.6 to 189.7 mm (7.46 to 7.47 in.)



viii.
C171323C01
1.146,1.167 1.146,1.865 false 1.073,1.885 1.458,2.104 0.385,0.219 10 false *1
*1 Nut


If the shoe diameter is not as specified, adjust it by turning the nut.


ix.
C171324N01
0.885,0.083 1.229,0.365 0.344,0.281 10 false (A)

The gap between the adjusting nut and screw must not exceed 5 mm (0.197 in.). If the gap is set to this specification and the shoe diameter is less than specified, replace the parking brake shoe. If the lining thickness is less than 1.5 mm (0.0591 in.) or exhibits uneven wear, replace the parking brake shoe.

Dimension (A):

5 mm (0.197 in.) max




xi.

Check for drag. Spin the rotor and ensure there is no drag from the parking brake shoe.

HINT:

If there is drag, apply and release the parking brake pedal and retest. If drag is still present, remove the disc, remeasure and readjust the shoe diameter and centralize the shoe. Reassemble the disc and recheck for drag.



xii.

Install the parking brake shoe adjusting hole plug.


xiii.

Install the rear disc brake caliper assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT


xiv.

Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

Parking brake pedal travel:

9 to 12 notches at 300 N (31 kgf, 67.5 lbf)



xv.

Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


xvi.

Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.


xvii.

Check that the parking brake does not drag.


xviii.

Install the rear wheels.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)



b.

for ADVICS Made:

i.

Completely release the parking brake pedal.


ii.
C247507C01
0.854,1.448 1.438,1.448 true 0.396,1.417 0.729,1.417 true 1.469,1.354 1.781,1.552 0.313,0.198 10 false *1 0.24,1.333 0.552,1.531 0.313,0.198 10 false *2
*1 Lock Nut
*2 Adjusting Nut


Loosen the lock nut and the adjusting nut to completely release the parking brake cable.


iii.

Remove the rear wheels.


iv.

Temporarily install the hub nuts to the hub bolts.

HINT:

Securely install the hub nuts to the rear disc.



v.

Remove the parking brake shoe adjusting hole plug.


vi.
C239414C02
1.833,0.406 1.833,0.385 false
V100135

Expand
V100136

Contract


Turn the shoe adjuster and expand the shoes until the disc locks.


vii.

Turn and contract the shoe adjuster until the disc can rotate smoothly.

Standard:

Returns 8 notches.



viii.

Check that there is no brake drag against the shoes.


ix.

Install the parking brake shoe adjusting hole plug.


x.

Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

Parking brake pedal travel:

7 to 10 notches at 300 N (31 kgf, 67.5 lbf)



xi.

Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


xii.

Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.


xiii.

Check that the parking brake does not drag.


xiv.

Remove the hub nuts from the hub bolts.


xv.

Install the rear wheels.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)



Hide 5.ADJUST PARKING BRAKE LEVER TRAVEL (for Manual Transaxle)

a.

for PBR Made:

i.

Remove the rear console upper panel sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


ii.

Completely release the parking brake lever.


iii.
C240908C01
2.531,1.354 2.281,1.354 false 2.76,1.458 2.99,1.458 false 2.135,1.271 2.292,1.448 0.156,0.177 10 true *1 3,1.375 3.26,1.583 0.26,0.208 10 true *2
*1 Lock Nut
*2 Adjusting Nut


Loosen the lock nut and the adjusting nut to completely release the parking brake cable.


iv.

Remove the rear wheels.


v.

Separate the rear disc brake caliper assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT


vi.

Remove the parking brake shoe adjusting hole plug.



viii.
C240909

Measure the brake shoe diameter as shown in the illustration.

Standard diameter:

189.6 to 189.7 mm (7.46 to 7.47 in.)



ix.
C171323C01
1.146,1.167 1.146,1.865 false 1.073,1.885 1.458,2.104 0.385,0.219 10 false *1
*1 Nut


If the shoe diameter is not as specified, adjust it by turning the nut.


x.
C171324N01
0.885,0.083 1.229,0.365 0.344,0.281 10 false (A)

The gap between the adjusting nut and screw must not exceed 5 mm (0.197 in.). If the gap is set to this specification and the shoe diameter is less than specified, replace the parking brake shoe. If the lining thickness is less than 1.5 mm (0.0591 in.) or exhibits uneven wear, replace the parking brake shoe.

Dimension (A):

5 mm (0.197 in.) max




xii.

Check for drag. Spin the rotor and ensure there is no drag from the parking brake shoe.

HINT:

If there is drag, apply and release the parking brake lever and retest. If drag is still present, remove the disc, remeasure and readjust the shoe diameter and centralize the shoe. Reassemble the disc and recheck for drag.



xiii.

Install the parking brake shoe adjusting hole plug.


xiv.

Install the rear disc brake caliper assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT


xv.

Turn the adjusting nut until the parking brake lever travel is corrected to be within the specified range.

Parking brake lever travel:

7 to 10 notches at 200 N (20 kgf, 45.0 lbf)



xvi.

Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


xvii.

Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.


xviii.

Check that the parking brake does not drag.


xix.

Install the rear wheels.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)


xx.

Install the rear console upper panel sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>INSTALLATION



b.

for ADVICS Made:

i.

Remove the rear console upper panel sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


ii.

Completely release the parking brake lever.


iii.
C240908C01
2.531,1.354 2.281,1.354 false 2.76,1.458 2.99,1.458 false 2.135,1.271 2.292,1.448 0.156,0.177 10 true *1 3,1.375 3.26,1.583 0.26,0.208 10 true *2
*1 Lock Nut
*2 Adjusting Nut


Loosen the lock nut and the adjusting nut to completely release the parking brake cable.


iv.

Remove the rear wheels.


v.

Temporarily install the hub nuts to the hub bolts.

HINT:

Securely install the hub nuts to the rear disc.



vi.

Remove the parking brake shoe adjusting hole plug.


vii.
C239414C02
1.833,0.406 1.833,0.385 false
V100135

Expand
V100136

Contract


Turn the shoe adjuster and expand the shoes until the disc locks.


viii.

Turn and contract the shoe adjuster until the disc can rotate smoothly.

Standard:

Returns 8 notches.



ix.

Check that there is no brake drag against the shoes.


x.

Install the parking brake shoe adjusting hole plug.


xi.

Turn the adjusting nut until the parking brake lever travel is corrected to be within the specified range.

Parking brake lever travel:

7 to 10 notches at 200 N (20 kgf, 45.0 lbf)



xii.

Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


xiii.

Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.


xiv.

Check that the parking brake does not drag.


xv.

Install the rear wheels.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)


xvi.

Install the rear console upper panel sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>INSTALLATION



Hide 6.INSPECT BRAKE WARNING LIGHT

a.

When operating the parking brake pedal or parking brake lever, check that the brake warning light illuminates.

Standard:

The brake warning light always illuminates at the first click.