Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM19V0EQ _55 Steering _014596 POWER ASSIST SYSTEMS _0074061 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the EPS warning light.

WIRING DIAGRAM

C250552E01
1.263,1.2 1.438,1.361 0.175,0.161 10 13 0.964,1.298 1.166,1.459 0.203,0.161 10 TC 2.986,1.2 3.159,1.361 0.173,0.161 10 23 4.115,0.606 4.328,0.767 0.213,0.161 10 26 3.633,0.704 4.023,0.865 0.39,0.161 10 CANL 4.123,1.998 4.321,2.159 0.198,0.161 10 13 3.61,2.096 4.023,2.257 0.413,0.161 10 CANH 5.971,0.704 6.361,0.865 0.39,0.161 10 CANL 5.78,0.606 5.875,0.767 0.095,0.161 10 8 5.78,1.998 5.875,2.159 0.095,0.161 10 4 5.971,2.096 6.383,2.257 0.413,0.161 10 CANH 1.263,1.934 1.438,2.095 0.175,0.161 10 4 0.938,2.032 1.166,2.193 0.228,0.161 10 CG 0.436,2.739 0.69,2.9 0.254,0.161 10 I39 0.758,2.739 1.134,2.9 0.376,0.161 10 DLC3 3.645,2.756 4.062,2.919 0.417,0.163 10 ECM 5.845,2.756 6.813,3.086 0.968,0.33 10 Power Steering ECU Assembly 5.669,2.763 5.841,2.945 0.172,0.182 10 j1 3.299,1.298 3.55,1.459 0.251,0.161 10 TC 3.309,2.756 3.603,2.917 0.295,0.161 10 A25

HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


INSPECTION PROCEDURE

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)

B

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13(TC) - A25-23(TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C207407C47
1.51,0.865 1.917,1.115 0.406,0.25 1.188,1.406 1.583,1.885 false 0.177,0.177 0.75,0.594 0.573,0.417 10 *a 1.063,1.219 1.406,1.458 0.344,0.24 10 CG 1.604,0.906 2.01,1.281 0.406,0.375 10 I39
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)
a.
C207407C51
1.51,0.865 1.917,1.115 0.406,0.25 2.531,1.448 1.854,2.365 false 0.177,0.177 0.75,0.594 0.573,0.417 10 *a 2.49,1.25 2.833,1.49 0.344,0.24 10 TC 1.604,0.906 2.01,1.281 0.406,0.375 10 I39
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE WIRE HARNESS OR EACH ECU